Westell Kentrox RMM-700 Manuale utente
© Westell Technologies
Part # 030-300653
WESTELL.COM
INSTALLATION GUIDE
Remote RMM-700
Intelligent Site Management Device
Installation Guide
WESTELL.COM
Page 2
Remote RMM-700 Installation Guide
1-800-377-8766
Copyright © 2015 by Westell, Inc. All Rights Reserved. Westell, Kentrox, and Optima Management
System are registered trademarks of Westell. All other names are trademarks of their respective
owners.
Information is correct at time of publication and is subject to change without notice. Contact
Westell in Aurora, Illinois, to verify current product information. Westell, Inc. is an Equal
Opportunity/Affirmative Action employer.
Westell, Inc.
750 North Commons Drive
Aurora, Illinois 60504 USA
Toll Free: (800) 247-9482
International: +1 (614) 798-2000
Fax: +1 (614) 798-1770
WESTELL.COM
Remote RMM-700 Installation Guide
Product Components
1-800-377-8766
Page 3
Product Components
Front Panel Components - Remote RMM-700
LED Status LED Description
ALM Summary alarm LED: Illuminates when any point is
in alarm state
DC DC input power LED: Illuminated when valid DC
input power is applied to the unit
FLT Hardware Failure LED:
-- Illuminates when processor is not functioning, or
when RMM-700 has been powered up and
bootloader is loading
-- Blinks when bootloader has loaded and kernel is
loading
-- Goes out when RMM-700 bootup is completed
Pinouts-see
page 4
Analog Input
2 Ethernet Ports
2 Serial Ports
SiteBus Connection
Tx/Rx SMA
Female Cellular/
PCS Antenna Diversity SMA Female
Cellular/PCS Antenna
DC Power Inputs
A & B
12 Discrete Ports
Relay
Serial port 1 operates only
in RS232 mode. Serial port
2 operates in RS485 mode
or RS422 mode.
Unit Status LEDs
Chassis
Ground
WESTELL.COM
Page 4
Remote RMM-700 Installation Guide
Pinouts
1-800-377-8766
Pinouts SiteBus Port
Pin Signal
1 No connection
2+5
3 No connection
4 data
6 ground
6 No connection
7 No connection
8 No connection
8 1
Asynchronous Serial Ports
RS232 Mode
Pin Signal Direction
1 RTS Output
2 DTR Output
3 TXD Output
4 Ground
5 Ground
6 RXD Input
7 DSR Input
8 CTS Input
RS422 Mode Full Duplex
Pin Signal Direction
1 Reserved*
2 TXb Output
3 TXa Output
4 Ground
5 Ground
6 RXa Input
7 RXb Input
8 Reserved*
8 1
RS485 ModeHalf Duplex
Pin Signal Direction
1 Reserved*
2 TXRXb Bidirectional
3 TXRXa Bidirectional
4 Ground
5 Ground
6 Hi-Z
7 Hi-Z
8 Reserved*
* On serial port 2, these pins
are reserved for diagnostic
access. Contact Westell
Customer Assistance for
more information.
Ethernet Switch Ports
Pin Signal Direction
1 RX+ Input
2 RX- Input
3 TX+ Output
4 Termination
5 Termination
6 TX- Output
7 Termination Input
8 Termination Input
Illuminates when a
link is established.
Blinks when data
transfer is active.
81
WESTELL.COM
Remote RMM-700 Installation Guide
Cautions and Warnings
1-800-377-8766
Page 5
Cautions and Warnings
Grounding and Electrical Safety
CAUTION: Westell’s Kentrox equipment and peripherals contain electrostatic
sensitive components. Proper handling, shipping, and storage precautions
must be exercised.
CAUTION: During installation, read and observe all additional Cautions and Warnings
shown in Step 1: Install SIM Chip and Wireless Phone Module Hardware in
Remote RMM-700, Step 4: Attach Chassis Ground, and Step 5: Connect
DC Power Input.
Installation
CAUTION: For Westell’s Kentrox equipment to operate safely and correctly, there
must be a safety ground strap between the equipment ground bolts and
the office ground.
Environment
CAUTION: In the event that Remote RMM-700 has been subjected to adverse
environmental conditions, a service inspection of Remote RMM-700
should be made to ensure safe operation.
Restricted Access Locations
CAUTION: The Remote RMM-700 is for use in restricted access locations only.
FCC
The Federal Communications Commission has set limits for emitted radio interference,
and Remote RMM-700 is constructed with this electromagnetic interference (EMI)
limitation in mind. Remote RMM-700 is classified under FCC regulations as a Class A
device, that is, a device for use in commercial environments and not in residential areas.
This device has been tested and shown to comply with the following FCC rule: Part 15
Subpart J. Operation of this equipment in a residential area may cause interference to
radio and TV reception, requiring the user to take whatever steps are necessary to
correct the interference.
WESTELL.COM
Page 6
Remote RMM-700 Installation Guide
Cautions and Warnings
1-800-377-8766
Information is available from the FCC describing possible corrective actions. To
maintain low EMI levels, we suggest that you use only metal connectors and shielded
cable grounded to the frame.
Specifications are subject to change without notice.
Clock Battery
CAUTION: The Real Time Clock battery is intended to last for the life of the product,
and should not require replacement under normal operation. If for any
reason the battery does require replacement, the unit should be returned
for service at Kentrox. Contact Customer Assistance if this need arises.
WESTELL.COM
Remote RMM-700 Installation Guide
Customer Assistance
1-800-377-8766
Page 7
Customer Assistance
All customers, partners, and resellers who have a valid Westell Support and Services
Agreement have complete access to the technical support resources.
Westell offers technical support from 8 a.m. to 5 p.m. Eastern time, Monday - Friday.
Before you contact Westell for assistance, please have the following information
available:
The version of hardware and software you are currently running
The error number and exact wording of any messages that appeared on your screen
What happened and what you were doing when the problem occurred
How you tried to solve the problem
Email Support
Email support is available. You may send email at any time during the day; however,
responses will be provided only during normal business hours, in accordance with your
Service and Support Agreement.
To contact Technical Support, send email to:
Telephone Support
Pre-sales support
Available, at no charge, to anyone who needs technical assistance in determining how
Westell products or solutions can help solve your technical needs. Representatives are
standing by to assist with customer account information and product ordering and
answer questions regarding Westell products and solutions.
Phone number: 800-377-8766, option 1
Hours of Operation: 9 a.m. – 5 p.m. Eastern Time
Post-sales technical support
Available to qualified Westell customers or partners who have not been able to resolve
their technical issue by using our online services. To qualify for support, you must have a
valid Support and Services Agreement.
Phone number: 800-377-8766, option 2
Normal Business Hours: 8 a.m. to 6 p.m. Eastern time
After-Hours Support: Available to qualified customers who are experiencing service-
affecting outages that cannot wait until the next business day. To qualify for after-hours
WESTELL.COM
Page 8
Remote RMM-700 Installation Guide
Customer Assistance
1-800-377-8766
support, you must have a valid 24x7 Support and Services Agreement. Call the number
above, option 2, and follow the prompts for after-hours service.
Product Documentation
You can also access and view the most current versions of Kentrox product
documentation on our Web site at:
http://www.westell.com
WESTELL.COM
Remote RMM-700 Installation Guide
Required Tools and Materials
1-800-377-8766
Page 9
Required Tools and Materials
Tools
#2 Phillips screwdriver
Small flathead screwdriver (Phoenix 3 mm, recommended)
Crimping tool
Wire cutter
Wire stripper
ESD wrist strap
PC or laptop with Kentrox Redirect software installed
Materials
Screws and lock washers sized to fit your equipment rack
Wire for input power connections (16 AWG solid or stranded insulated)
Wire for ground connection (14 AWG, copper conductor)
Ground lugs for rack or other earth ground
Antioxidant
Various required rack cables and cable assemblies. For assistance in acquiring
cables, contact Westell Customer Assistance.
WESTELL.COM
Page 10
Remote RMM-700 Installation Guide
Installation
1-800-377-8766
Installation
Step 1: Install SIM Chip and Wireless Phone Module Hardware in
Remote RMM-700
CAUTION: Kentrox equipment and peripherals contain electrostatic sensitive
components. Proper handling precautions must be exercised.
If your Remote RMM-700 includes the wireless phone module, follow these steps to
install the necessary hardware:
Note: Installation of a SIM Chip and/or wireless phone module is not necessary in all
applications. If your Remote RMM-700 comes with the phone module and SIM
chip installed, proceed to Step 2: Install Mounting Flanges.
1. Affix the FCC sticker (included with the phone module) to the product label on
Remote RMM-700.
2. Using a screwdriver, remove the top/back cover from Remote RMM-700 by
removing the screws from both sides of the top and the center of the back of the
unit. (See Figure 1-1 on page 10). Slide the top cover back and remove it from the
unit.
Figure 1-1 The installer removes the screw from the back side of Remote RMM-700.
Screws
Indice
Altri manuali Westell Controllori
