WESTERSTRAND Lumex 5 Manuale utente

Dokument: 1824en06doc

Förf.: TAn

Datum: 2014-01-07

Sida: 1 av 17

WESTERSTRAND URFABRIK AB

Box 133 Tel. 0506 48 000 Internet:: www.westerstrand.se

545 23 TÖREBODA Fax. 0506 48 051 E-mail: info@westerstrand.se

Instructions

Digital clock

LUMEX 5, LUMEX 7, LUMEX 12

With chronometer function

Dokument: 1824en06doc

Förf.: TAn

Datum: 2014-01-07

Sida: 2 av 17

WESTERSTRAND URFABRIK AB

Box 133 Tel. 0506 48 000 Internet:: www.westerstrand.se

545 23 TÖREBODA Fax. 0506 48 051 E-mail: info@westerstrand.se

General

This device is for use alternatively as digital clock or as chronometer.

Digital clock for indoor application has 4 digits and colon displaying time.

The digits consists 7 segments. Each segment has 4 LED:s.

Example

Digital clock for indoor application with second has 6 digits and colon displaying time.

The digits for the second consists 7 segments. Each segment has 3 LED:s.

Example

The Digital clock can be programmed for alternating time/date/temperature display in 0-25 sec

intervals.

Temperature sensor is not included. It is an option.

The programming of time, Synchronisation and light intensity are made by push buttons, situated at

one side of the cover.

The digital clock can operate stand alone with a built in quartz crystal as time reference, as a slave

clock to a master clock transmitting 24 V polarised 1/1 minute impulses or synchronised by TC, DCF.

If the DLS-function is set , the clock is changing, summer and winter time, the last Sunday in March

and the last Sunday in October automatically.

The clock has adjustable light intensity.

If power failure occurs the display is turned off. The internal clock continues to keep the correct time

for 48 hours. After power failure the display is turned on and correct time is shown.

Installation

·Unscrew 4 screws, 2 above and 2 under, remove the back plate from the casing and mount it on the

wall.

·If operated by synchronisation, check the strapping according to the drawing page 5. Connect the

cables according the schema.

·Connect the power 230VAC, 50Hz. according the schema. When the clock is permanently installed

a readily accessible disconnect device shall be incorporated in the fixed wires.

·Setting the digital clock. See Programming.

23:59

:59:

Dokument: 1824en06doc

Förf.: TAn

Datum: 2014-01-07

Sida: 3 av 17

WESTERSTRAND URFABRIK AB

Box 133 Tel. 0506 48 000 Internet:: www.westerstrand.se

545 23 TÖREBODA Fax. 0506 48 051 E-mail: info@westerstrand.se

Connection

The connections are made at the back plate (see below.)

LUMEX 5

LUMEX 5/S, LUMEX 7, LUMEX 7/S, LUMEX 12, LUMEX 12/S

Dokument: 1824en06doc

Förf.: TAn

Datum: 2014-01-07

Sida: 4 av 17

WESTERSTRAND URFABRIK AB

Box 133 Tel. 0506 48 000 Internet:: www.westerstrand.se

545 23 TÖREBODA Fax. 0506 48 051 E-mail: info@westerstrand.se

Connection Wired remote control chronometer

Connection from standard remote control to connection terminal.

1- Blue---------Down

2- White-------Yes

3- Green-------No

4- Yellow------Up

5- Brown------Mode

6- Red---------S/S

7- Grey--------Preset

8- Pink--------Common

Connection from flush mounted remote control to connection terminal.

YESNO

PRESET MODES/S

Dokument: 1824en06doc

Förf.: TAn

Datum: 2014-01-07

Sida: 5 av 17

WESTERSTRAND URFABRIK AB

Box 133 Tel. 0506 48 000 Internet:: www.westerstrand.se

545 23 TÖREBODA Fax. 0506 48 051 E-mail: info@westerstrand.se

Connection Synchronisation wire

TC/MIN-imp 3,4

DCF 2-line 3 –V+, 5 –GND

DCF 3-line 3 –V+,4- DCF, 5 –GND

Sync. input

12345

Dokument: 1824en06doc

Förf.: TAn

Datum: 2014-01-07

Sida: 6 av 17

WESTERSTRAND URFABRIK AB

Box 133 Tel. 0506 48 000 Internet:: www.westerstrand.se

545 23 TÖREBODA Fax. 0506 48 051 E-mail: info@westerstrand.se

Strapping/DIP switch setting for TC / MIN-impulse (default)

Strapping/DIP switch setting for DCF-radio (2 –wire) computer board

Dokument: 1824en06doc

Förf.: TAn

Datum: 2014-01-07

Sida: 7 av 17

WESTERSTRAND URFABRIK AB

Box 133 Tel. 0506 48 000 Internet:: www.westerstrand.se

545 23 TÖREBODA Fax. 0506 48 051 E-mail: info@westerstrand.se

Strapping/DIP switch setting for DCF-radio (3 –wire) computer board

The DIP-switch on the computer board should be set as follows:

Dip 1: OFF Display format is HH:MM.

ON Display format is HH:MM:SS.

Dip 2: OFF always OFF

Dip 3: OFF TC/Min impulse synchronisation. (default)

ON DCF synchronisation.

Dip 4: OFF TC/Min impulse or 3-wire DCF synchronisation. (default)

ON 2-wire DCF synchronisation.

Dip 5: OFF DCF synchronisation.

ON TC/Min impulse synchronisation.(default)

Dip 6: OFF ½ Min impulse synchronisation.

ON TC/Min impulse synchronisation or DCF synchronisation. (default)

Dip 7: OFF always OFF

Dip 8: OFF always OFF

Dokument: 1824en06doc

Förf.: TAn

Datum: 2014-01-07

Sida: 8 av 17

WESTERSTRAND URFABRIK AB

Box 133 Tel. 0506 48 000 Internet:: www.westerstrand.se

545 23 TÖREBODA Fax. 0506 48 051 E-mail: info@westerstrand.se

Synchronisation

Stand alone

If the clock does not have an external synchronisation, it operates Stand alone.

Minute impulse

Make the strapping according to the drawing for strapping page 5.

Connect the minute impulse wire according to the schema page 4.

The clock can be set in synchronisation or slave mode.

Synchronisation mode:

Set the clock for synchronisation, mode InSy See programming page 10.

Set time and wait for next minute impulse. The clock will be synchronised

Slave mode:

Set the clock for slave, mode InSL See programming page 10.

Set time and wait for next minute impulse. The clock operates as a slave clock.

Check the strapping according to the drawing for strapping page 5.

Connect the TC wire according to the schema page 4.

Set the clock for synchronisation, function DCF See programming page 10.

When a correct time message appears the clock sets the time.

The clock will blink colon when it is in sync and accepts transmitted code.

DCF

Check the strapping according to the drawing for strapping page 5.

Connect the DCF wire according to the schema page 4.

Set the clock for synchronisation, function DCF See programming page 10.

When a correct time message appears, the clock sets the time.

The clock will blink colon when it is in sync and accepts transmitted code.

Dokument: 1824en06doc

Förf.: TAn

Datum: 2014-01-07

Sida: 9 av 17

WESTERSTRAND URFABRIK AB

Box 133 Tel. 0506 48 000 Internet:: www.westerstrand.se

545 23 TÖREBODA Fax. 0506 48 051 E-mail: info@westerstrand.se

Connection temperature sensor (this is an option).

Temperature sensor connection

1 red.

2 black

5 Screen

12345

Dokument: 1824en06doc

Förf.: TAn

Datum: 2014-01-07

Sida: 10 av 17

WESTERSTRAND URFABRIK AB

Box 133 Tel. 0506 48 000 Internet:: www.westerstrand.se

545 23 TÖREBODA Fax. 0506 48 051 E-mail: info@westerstrand.se

Programming

The programming is made by push buttons (see below).

R (Return) Enter the base mode (display time)

F (Function)Next function / Accept displayed value

P (Program)Enter the displayed function / Increase displayed value.

programming time

Push [F] until display shows

Push [P] display shows year.

Push [P] until desired year (00-99)

Accept with [F].

Display shows month.

Push [P] until desired month (1-12).

Accept with [F].

ti ne

yy 95

nn 1

Altri manuali per Lumex 5

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali WESTERSTRAND Orologio

WESTERSTRAND

WESTERSTRAND mini WDP-Y Manuale utente

WESTERSTRAND

WESTERSTRAND Analogue NTP Clock Manuale utente

WESTERSTRAND

WESTERSTRAND Quartz Movement Manuale utente

WESTERSTRAND

WESTERSTRAND AUREA II Manuale utente

WESTERSTRAND

WESTERSTRAND QUARTZ MOVEMENT Manuale utente

WESTERSTRAND

WESTERSTRAND CIRCLE LINE Manuale utente

WESTERSTRAND

WESTERSTRAND AUREA ALPHA Manuale utente

WESTERSTRAND

WESTERSTRAND CIRCLE LINE Manuale utente

WESTERSTRAND

WESTERSTRAND QWTIME III WDP-WL Manuale utente

WESTERSTRAND

WESTERSTRAND QUARTZ CLOCK Manuale utente

WESTERSTRAND

WESTERSTRAND Analogue clock Manuale utente

WESTERSTRAND

WESTERSTRAND Wireless Clock Manuale utente

WESTERSTRAND

WESTERSTRAND Lumex 5 Manuale utente

WESTERSTRAND

WESTERSTRAND CIRCLE LINE NTP PoE Manuale utente

WESTERSTRAND

WESTERSTRAND QWTIME III WDP M+S Manuale utente

WESTERSTRAND

WESTERSTRAND Analog indoor clock with WiFi Manuale utente

WESTERSTRAND

WESTERSTRAND LUMEX 7 Manuale utente

WESTERSTRAND

WESTERSTRAND Analogue NTP Clock Manuale utente

WESTERSTRAND

WESTERSTRAND CIRCLE LINE NTP Manuale utente

WESTERSTRAND

WESTERSTRAND Lumex 5 Manuale utente

WESTERSTRAND

WESTERSTRAND Analogue NTP Clock Manuale utente

WESTERSTRAND

WESTERSTRAND KNX Manuale utente

Manuali Orologio popolari di altre marche

Silicon Laboratories

Silicon Laboratories SI5324 Manuale utente

Heathkit

Heathkit GC-1005 Manuale utente

Oregon Scientific

Oregon Scientific PRYSMA RMR221P Manuale utente

Andrew O'Malley

Andrew O'Malley DOTKLOK Manuale utente

ALGE-Timing

ALGE-Timing ASC3 Manuale utente

Bodet

Bodet Profil 960 Manuale utente

Nixie Clock

Nixie Clock Divergence Meter Manuale utente

La Crosse Technology

La Crosse Technology WS-8256-AL Manuale utente

Mini Gadgets

Mini Gadgets MCPro Manuale utente

Casio

Casio TMR-200 Manuale utente

Progetti

Progetti ILTEMPOSTRINGE Manuale

BVItech

BVItech BV-101 Manuale utente

Progetti

Progetti KALIMERO Manuale

La Crosse Technology

La Crosse Technology WT-3141b Manuale

La Crosse Technology

La Crosse Technology W86531 Manuale utente

Sharp

Sharp SPC900 Manuale utente

La Crosse Technology

La Crosse Technology 404-50447 Manuale utente

Datexx

Datexx DF0063 Manuale utente