Westover CleanBlast Manuale utente
Patent Pending
User Guide
© 2004 Westover Scientific, Inc.
For Bench-Top and Portable
System Configurations
© 2004 Westover Scientific, Inc.
All rights reserved. No part of this publication may be reproduced, stored in a retrieval
system, or transmitted in any form, be it electronically, mechanically, or by any other
means such as photocopying, recording, or otherwise, without the prior written
permission of Westover Scientific Inc. (WSI).
3
Information
Important Information
Information provided by WSI is believed to be accurate and reliable. However, no responsibility is assumed
by WSI for its use.
WSI’s Commerce And Government Entities (CAGE) code under the North Atlantic Treaty Organization
(NATO) is 0L8C3.
The information contained in this publication is subject to change without notice.
Words that WSI considers trademarks have been identified as such. However, neither the presence nor
absence of such identification affects the legal status of any trademark.
Units of measurement in this document conform to SI standards and practices.
F.C.C. Information
Electronic test equipment is exempt from Part 15 compliance (FCC) in the United States.
Electronic test equipment is subject to the EMC Directive in the European Union. The
EN61326 standard prescribes both emission and immunity requirements for laboratory,
measurement, and control equipment.
Independent Laboratory Testing
This unit has undergone extensive testing according to the European Union Directive and Standards. All
pre-qualification tests were performed internally, at WSI, while all final tests were performed externally, at
an independent, accredited laboratory. This guarantees the unerring objectivity and authoritative
compliance of all test results.
This equipment has been tested and found to comply with the EN 61000-6-3:2001 specifications for
electronic and electronic apparatus intended for use in residential, commercial, and light industrial
environment. In addition, this equipment has been tested and found to comply with the EN 61000-6-
1:2001 specifications for immunity of residential, commercial and light industrial equipment. The
requirements of these rules and the measurement methods used for assessing equipment compliance to
these rules are available upon request from Westover Scientific.
Certification
4
You should understand the following conventions before using the product
described in this manual:
WARNING
Refers to a potential personal hazard. It requires a procedure which, if not
correctly followed, may result in bodily harm or injury. Do not proceed unless
you understand and meet the required conditions.
CAUTION
Refers to a potential product hazard. It requires a procedure which, if not
correctly followed, may result in component damage. Do not proceed unless
you understand and meet the required conditions.
IMPORTANT
Refers to any information regarding the operation of the product which you
should not overlook.
Safety Conventions
5
Safety Information
Cleaning Solvent
HFE-Based Cleaning Fluid
IMPORTANT
User is responsible for determining whether this product is fit for a
particular purpose and suitable for user’s method of use or application.
Given the variety of factors that can affect the use and application of this
product, some of which are uniquely within the user’s knowledge and
control, it is essential that the user evaluate this product to determine
whether it is fit for a particular purpose and suitable for user’s method of
use or application.
Intended Use: FOR INDUSTRIAL USE ONLY. NOT INTENDED FOR USE AS A
MEDICAL DEVICE OR DRUG.
Specific Use: Cleaning Solvent for use in the CleanBlast™ System
CAUTION
DO NOT SUBSTITUTE ANY OTHER CLEANING SOLUTION.
Product Information Source: Material Safety Data Sheet or
Westover Scientific, Inc.
Mill Creek, WA 98012
1-800-304-3202 or (425) 398-1298
(7 a.m. to 5 p.m. PST)
6
Safety Information
Cleaning Solvent
WARNING
STORAGE
Store away from heat. Store out of direct sunlight. Store away from
oxidizing agents. Keep container tightly closed. Keep container in well-
ventilated area. Store away from strong bases. Contents may be under
pressure if stored/shipped under elevated temperature. Open closure slowly
to vent pressure.
INGREDIENTS C.A.S. No. % by Wt
1,2-TRANS-DICHLOROETHYLENE 156-60-5 66 - 70
ETHYL NONAFLUOROISOBUTYL ETHER 163702-06-5 4 - 16
ETHYL NONAFLUOROBUTYL ETHER 163702-05-4 4 - 16
METHYL NONAFLUOROISOBUTYL ETHER 163702-08-7 2 - 8
METHYL NONAFLUOROBUTYL ETHER 163702-07-6 2 - 8
ISOPROPYL ALCOHOL 67-63-0 1 - 3
7
FIRST AID INSTRUCTIONS:
The following first aid recommendations are based on an assumption that
appropriate personal and industrial hygiene practices are followed.
Eye Contact: Flush eyes with large amounts of water. If signs/symptoms
persist, get medical attention.
Skin Contact: Remove contaminated clothing and shoes. Immediately
flush skin with large amounts of water. Get medical attention. Wash
contaminated clothing and clean shoes before reuse.
Inhalation: Remove person to fresh air. If signs/symptoms develop, get
medical attention.
If Swallowed: Do not induce vomiting unless instructed to do so by
medical personnel. Give victim two glasses of water. Never give anything
by mouth to an unconscious person. Get medical attention.
Safety Information
Cleaning Solvent
8
Warranty Information
General Information
Westover Scientific, Inc. (WSI) warrants this equipment against defects in material and workmanship for a
period of one year from the date of original shipment. WSI also warrants that this equipment will meet
applicable specifications under normal use.
During the warranty period, WSI will, at its sole discretion, repair, replace, or issue
credit for any defective product free of charge should the equipment need to be repaired.
IMPORTANT
The warranty will become null and void if
• the equipment has been tampered with, repaired, or worked
upon by unauthorized individuals or non-WSI personnel.
• the warranty label has been removed.
• product enclosure screws, other than those specified in this
manual, have been removed.
• the product enclosure has been opened, other than as explained
in this manual.
• the equipment serial number has been altered, erased, or
removed.
• the equipment has been misused, neglected, or damaged by
accident.
9
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED, IMPLIED,
OR STATUTORY, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT
SHALL WESTOVER BE LIABLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES.
Liability
WSI shall not be liable for damages resulting from the use of the purchased product, nor
shall be responsible for any failure in the performance of other items to which the purchased
product is connected or the operation of any system of which the purchased product may be
a part. WSI shall not be liable for damages resulting from improper usage or unauthorized
modification of the product, its accompanying accessories and software.
Warranty Information
General Information
10
Table of Contents
IMPORTANT INFORMATION ...................................................................... 3
Certification .................................................................................................. 3
SAFETY CONVENTIONS ............................................................................. 4
SAFETY INFORMATION ............................................................................. 5
Cleaning Solvent ........................................................................................... 5
WARRANTY INFORMATION ....................................................................... 8
TABLE OF CONTENTS .............................................................................. 10
INTRODUCTION ...................................................................................... 12
Contact Information .................................................................................... 12
BENCH-TOP SYSTEM OVERVIEW ............................................................. 13
Identifying the system components ............................................................... 13
System Status Indicators ............................................................................. 14
Controls & Functions.................................................................................... 15
Filter System .............................................................................................. 16
BENCH-TOP SYSTEM ASSEMBLY .............................................................. 17
Attaching necessary elements ....................................................................... 17
Attaching the Optional Exhaust Filter ............................................................. 18
BENCH-TOP SYSTEM QUICK START ......................................................... 21
Start-up Instructions ................................................................................... 21
BENCH-TOP SYSTEM OPERATION ............................................................ 22
Using a Video Inspection Probe ..................................................................... 22
BENCH-TOP SYSTEM MAINTENANCE ....................................................... 23
Scheduled and Preventative Maintenance ....................................................... 23
Refilling the Solvent Reservoir ...................................................................... 24
Replacing the disposable air filters................................................................. 26
BENCH-TOP SYSTEM SPECIFICATIONS .................................................... 27
Indice
