Page 5
5.0 Switch Operation:
5.1 Custom Dip Switch Configuration (BANK1):
Push-button 9 (momentary switch) can function in 4 different modes,
defined by the 4-position dip switch 1 (BANK1) (Fig. 2).
Mode 1 - (default) - In this configuration, the output is activated for as long
as push-button 9 is depressed.
Mode 2 - In this configuration, when push-button 9 is pressed, the output
is activated for a period of 8 seconds.
Mode 3 - In this configuration, when push-button 9 is pressed, the output
is activated. When pressed again, the output is deactivated.
Mode 4 - In this configuration, when push-button 9 is pressed, the output
is activated for a period of 400 ms. After 400 ms, the output is deactivated
for 400 ms. This cycle will continue until push-button 9 is pressed again.
Bank 1 Position 1
Enabling siren tones through slide switch position #3:
Slide switch position 3 can be configured to automatically activate siren
tones (See Section 4.0 - Rotary Switch Operations). If this is not desired,
make sure that Dip Switch Bank 1 position 1 is in the off position (the
factory default position). Please note that siren activation through slide
switch position 3 is only available when the power switch is in the ON
position.
5.2 Configuring the Slide Switch Functions:
In the default dip switch setting, the P1 outputs are:
Slide Switch Positions: Push-Buttons:
0 = ALL OFF 4 = WHT/YEL
1 = WHT/BRN 5 = WHT/GRN
2 = WHT/RED, WHT/BRN 6 = WHT/BLU
3 = WHT/BRN, WHT/RED, WHT/ORG 7 = WHT/VIO
8 = WHT/GRY
9 = WHT
Changing Default Slide Switch Control:
The slide switch has four positions: 0 (off), 1, 2 & 3. When in position 0
(furthest to the left) the slide switch will not activate any outputs. In
position 1, 2 or 3 the slide switch can activate any combination of outputs
1 through 8. Each active slide switch position uses a bank of dip switches
to determine which outputs are to be active while the slide switch is in that
position; position 1 uses BANK4, position 2 uses BANK3, and position 3
uses BANK2 (Fig. 2).
Each dip switch bank is comprised of 8
switches, each representing a
corresponding output (DIPSW-1 for
WHT/BRN, DIPSW-2 for WHT/RED,
etc.). If, for example, switches 1, 3, 4 & 6
on BANK4 are in the ON position, outputs
WHT/BRN, WHT/ORG, WHT/YEL, WHT/
BLU will be active when the slide switch
is moved to position 1.
Slide switch configuration can be
accomplished by deciding which outputs
are to be active in a given position and then moving the corresponding dip
switch on the appropriate dip switch bank to the ON position.
6.0 Siren Tone Programing Procedures
With Scan-Lock the tonal operation of the siren can be customized to
fit your needs. Scan-Lock is used to change the default siren tones.
To change the primary tone for rotary switch positions T1, T2, & T3:
Put the rotary switch in the
position that you wish to
change. Each time the
Scan-Lock switch is
pressed and released, the
next available tone will be
broadcast. When the
desired tone is generated, it
is automatically saved for that rotary switch position.
To change the override tone for rotary switch positions T1, T2. & T3:
Put the rotary switch in the
position that you wish to
change. Press and hold the
MAN button on the front
panel of the siren. Each
time Scan-Lock is pressed
and released, the next
available tone will be
broadcast. When the desired tone is present, release the MAN button and
it will automatically be saved as the override tone for that rotary switch
position.
To change one of the tones in the hands free cycle (see Section 4.4):
Put the rotary switch in the HF
position. Using the MAN button on
the front panel of the siren, advance
to the tone that you wish to change.
Now, each time Scan-Lock is
pressed and released, the next tone
will be broadcast. When the desired
tone is generated, it will
automatically be saved for that
hands-free cycle position.
To change the tone for rotary switch positions MAN1 or MAN2:
Put the rotary switch in the
position that you wish to change.
Press and hold the MAN button
on the front panel of the siren.
Each time Scan-Lock is pressed
and released, the next tone will
be broadcast. When the desired
tone is generated, release the
MAN button and it will
automatically be saved for that rotary switch position.
To change the override tone for rotary switch position RAD:
Put the rotary switch in the RAD
position. Press and hold the MAN
button on the front panel of the
siren. Each time Scan-Lock is
pressed and released, the next
tone will be broadcast. When the
desired tone is generated, release the MAN button and it will automatically
be saved for that rotary switch position.
To change the tone for the HORN button: Put the rotary switch in the
MAN2 position. Press and hold the HORN button on the front panel of the
siren. Each time Scan-Lock is pressed and released, the next tone will be
broadcast. When the desired tone is generated, it is automatically saved
for HORN button activation (Table 7).
TONE OFF
WAIL
YELP
PIERCER™
Y-249
HI/LOW
SIMULATED MECHANICAL
PULSED AIRHORN
AIRHORN HI/LOW
ALTERNATE WAIL
=Title 13 Compliant Tones
*
*
TABLE 3
yTone List For Rotar Switch Positions T1, T2 & T3
ALTERNATE YELP
WOOP
WARBLE
.
.
.
.
.
.
.
.
.
.
.
.
.
=Title 13 Compliant Tones
*
*
TABLE 4
Override Tone List For Rotar Switch Positions T1, T2 & T3y
TONE OFF
WAIL
YELP
PIERCER™
Y-249
.
.
.
.
.
ALTERNATE YELP
WOOP
WARBLE
AIRHORN
LOW FREQ. HORN
.
.
.
.
.
HI/LOW
SIMULATED MECHANICAL
PULSED AIRHORN
AIRHORN HI/LOW
ALTERNATE WAIL
.
.
.
.
.
WAIL
YELP
PIERCER™
Y-249
HI/LOW
SIMULATED MECHANICAL
TABLE 5
Tone List For Hands Free Operation:
PULSED AIRHORN
AIRHORN HI/LOW
ALTERNATE WAIL
ALT. YELP
WOOP
WARBLE
.
.
.
.
.
.
.
.
.
.
.
.
=Title 13 Compliant Tones
*
TONE OFF
MANUAL SIMULATED MECHANICAL COAST-TO-STOP
MANUAL SIMULATED MECHANICAL STOP
MANUAL WAIL COAST-TO-STOP
MANUAL WAIL STOP
AIRHORN
LOW FREQ. AIRHORN
TABLE 6
Tone List For MAN1 & MAN2 Operation:
.
.
.
.
.
.
.
TONE OFF
AIRHORN
LOW FREQUENCY
AIRHORN
TABLE 7
Override Tone List For Rotary Switch Position RAD
and the HORN button:
.
.
.
4321 4321 4321 4321
= OFF
= ON
Switch 9 can operate in four different modes, defined
by the 4-Position Dip Switch.
PANEL SWITCH 9
OPERATING MODE:
MOMENTARY
MODE 1 (DEFAULT)
PANEL SWITCH 9
OPERATING MODE:
8 SECOND ON TIMER
MODE 2
PANEL SWITCH 9
OPERATING MODE:
LATCH ON
LATCH OFF
MODE 3
PANEL SWITCH 9
OPERATING MODE:
FLASHER
(400MS ON & OFF)
MODE 4
