Whirlpool XHPC155YC Manuale utente
15.5" PEDESTAL INSTALLATION INSTRUCTIONS
For use only with front load washers and dryers
INSTRUCTIONS D’INSTALLATION DU PIÉDESTAL DE 15,5"
Pour utilisation avec les produits suivants seulement
laveuses et sécheuses à chargement par l’avant
W10347252B
W10348602B - SP
Table of Contents Table des matières
PEDESTAL SAFETY ......................................................1
INSTALLATION REQUIREMENTS................................2
Location Requirements .........................................2
Tools and Parts.......................................................2
UNPACKING THE PEDESTAL ......................................3
BEFORE INSTALLING THE PEDESTAL.......................3
INSTALLING THE PEDESTAL.......................................4
COMPLETE THE INSTALLATION.................................7
SÉCURITÉ DU PIÉDESTAL ..........................................9
EXIGENCES D’INSTALLATION ....................................9
Exigences d’emplacement....................................9
Outillage et pièces .................................................9
INSTRUCTIONS D’INSTALLATION ............................10
AVANT L’INSTALLATION DU PIÉDESTAL .................11
INSTALLATION DU PIÉDESTAL.................................12
ACHEVER L’INSTALLATION.......................................15
INSTALLATION NOTES
Date of purchase:_________________________________
Date of installation: _______________________________
Installer: ________________________________________
Model number: ___________________________________
Serial number: ___________________________________
NOTES CONCERNANT L’INSTALLATION
Date d’achat :_____________________________________
Date d’installation : ________________________________
Installateur : ______________________________________
Numéro de modèle :________________________________
Numéro de série :__________________________________
PEDESTAL SAFETY
Para una versión de estas instrucciones en español, visite www.whirlpool.com
2
TOOLS AND PARTS
Gather the required tools and parts before starting installation.
Tools Needed:
Utility knife 1/4" hex-head ratchet
or open-end wrench
Level 9/16" open-end wrench
Pliers or slip-joint pliers Bucket
INSTALLATION REQUIREMENTS
LOCATION REQUIREMENTS
NOTE: If the washer/dryer and pedestal assembly are located in
a garage, 3"(76 mm) must be added under the pedestal so that
the washer/dryer is 18" (458 mm) above the garage oor.
Towel Sponge
Parts Supplied:
Four #12 x 3/4" hex-head Drawer divider
sheet metal screws
Additional Items Needed:
1/4" nut driver 5/16"hex-head ratchet
or nut driver
3
NOTE: If the washer is to be transported, call your local service
center. To avoid suspension and structural damage, your
washer must be properly set up for relocation by a certied
technician.
1. Turn off the hot and cold water faucets.
2. Unplug the power supply cord.
3. Slowly loosen the ll hoses at the faucets to relieve the water
pressure. Use a sponge or towel to absorb the released water.
4. Remove the “HOT” and “COLD” ll hoses from the back of
the washer. Drain the water from the hoses into a bucket.
5. Remove the drain hose from the standpipe or laundry tub and
drain any water remaining in the hose into a bucket.
6. Pull the washer away from the wall so that you will have
enough space for the installation.
1. Empty pedestal drawer
UNPACKING THE PEDESTAL
Preparing the pedestal for installation
Open the pedestal drawer as far as possible and remove the
contents. The package contains four #12 x 3/4" hex-head
sheet metal screws and a drawer divider.
IMPORTANT: Set the pedestal box aside for use during
installation.
Hex-head screw
Drawer slide
3. Remove pedestal drawer
Using a 1/4" nut driver, remove the hex-head screws from both
drawer slides and save screws. Remove the drawer from the
slides and set aside. Push the slides back into the pedestal.
BEFORE INSTALLING PEDESTAL
IMPORTANT: If your washer and dryer are already installed,
they must be uninstalled.
Uninstalling your washer
To avoid possible damage to the washer, the transport bolts on
the back of the washer must be in place before installing the
pedestal. For more information on transport bolts see, “Remove
Transport System” in washer Use and Care Guide.
The four spacer pads are installed on the top of the pedestal.
These pads reduce vibration between the pedestal and the
washer/dryer.
NOTE: If your washer/dryer has feet installed, remove them.
Spacer pads
2. Locate spacer pads
4
Installation of new washer/dryer
1. Unpack the washer/dryer and move close to the intended
installation location.
1. Unplug the power supply cord or disconnect wiring if dryer is
direct wired.
2. Pull the dryer away from the wall enough to loosen the vent
clamp. Loosen the clamp and gently remove the exhaust vent
from the dryer exhaust outlet.
3. Pull the dryer away from the wall so that you will have enough
space for the installation.
Uninstalling your electric dryer
Uninstalling your gas dryer
1. Unplug the power supply cord.
2. Turn off the gas supply.
3. Pull the dryer away from the wall enough to loosen the vent
clamp. Loosen the clamp and gently remove the exhaust vent
from the dryer exhaust outlet.
4.
Disconnect the exible gas supply line from the dryer. Put a
piece of tape over the open ends of the gas line connection
ttings.
5. Pull the dryer away from the wall so that you will have enough
space for the installation.
INSTALLING THE PEDESTAL
Installing the pedestal on the washer
Conrm transport bolts are in place
Locate the transport bolts on rear of washer. Transport bolts
must remain in washer before pedestal can be installed. For
more information on transport bolts see, “Remove Transport
System” in washer Use and Care Guide.
5
2. Prepare the washer
Washer
bottom
Partially install two of the #12 x 3/4"
hex-head sheet metal screws in the
indicated holes. Leave a space of
about 3/8"(10 mm) between the
screw head and the bottom of
the washer.
NOTE: If your washer has leveling feet installed, remove them.
1. Place washer on its side
Pedestal box
Drawer divider
To avoid oor damage and ease installation and handling,
unfold the empty pedestal box at and place it next to the
washer. Position the drawer divider so that it will be near the
top of the washer, as shown. Gently tip the washer on its side
so the washer is resting on the drawer divider.
3. Attach pedestal to washer
Move the pedestal against the washer bottom. The front of
the pedestal cabinet should align with the washer cabinet
as shown below.
Slide the pedestal’s keyhole slots over the lower two partially
installed screws.
Pedestal Washer
Front
View from above
6
4. Secure pedestal to dryer
Position the pedestal toward the front of the dryer and install
the two remaining hex-head sheet metal screws. Do not tighten
completely. Now proceed to “Complete the pedestal installation”.
4. Secure pedestal to washer
Position the pedestal toward the front of the washer and
install the two remaining hex-head sheet metal screws.
Do not tighten completely. Now proceed to “Complete
the pedestal installation”.
2. Prepare the dryer
Dryer bottom
Partially install two of the #12 x 3/4" hex-head sheet metal
screws in the indicated holes. Leave a space of about 3/8"
(10 mm) between the screw head and the bottom of the dryer.
NOTE: If your dryer has leveling feet installed, remove them.
Do not install the feet that came with the new dryer.
Installing the pedestal on the dryer
3. Attach pedestal to dryer
Move the pedestal against the dryer bottom. The front of
the pedestal cabinet should align with the dryer cabinet
as shown below.
Slide the pedestal’s keyhole slots over the lower two partially
installed screws.
1. Place dryer on its side
Pedestal box
Drawer divider
To avoid oor damage and ease installation and handling,
unfold the empty pedestal box at and place it next to the dryer.
Position the drawer divider so that it will be near the top of the
dryer, as shown. Gently tip the dryer on its side so the dryer is
resting on the drawer divider.
Pedestal Dryer
Front
View from above
7
1"
(25 mm)
2. Prepare pedestal feet
Using a 1/4" hex head ratchet or open-end wrench, lower the
feet approximately 1" (25 mm) away from the bottom of the
pedestal.
1. Align sides of pedestal
Align the sides of the pedestal so that they are even with the
sides of the washer/dryer. Reach inside the pedestal opening
and securely tighten all four pedestal screws.
3. Stand the washer/dryer upright
1. Move close to nal location
Tip the washer/dryer back to its upright position. Remove
any remaining packaging material. Set the pedestal box aside
for use if installing another pedestal. Once both the washer
and dryer have been installed, dispose of/recycle all packaging
material.
Level the washer/dryer
Follow the installation instructions that came with your model
to nish installing or reinstalling your washer/dryer (i.e., hoses,
vents, etc.).
NOTE: Be sure to remove the transport bolts from the back
of the washer.
COMPLETE THE INSTALLATION
8
3. Adjust pedestal feet
4. Securely tighten jam nuts
2. Place drawer divider in drawer
Hex-head screw
Drawer slide
1. Reassemble pedestal drawer
2. Check levelness of washer/dryer
Place level here
Place a level on top edges of
washer/dryer, checking each side
and front. Rock washer/dryer back and forth to make sure all
four feet make solid contact with oor.
If not level, adjust pedestal feet up or down, repeating as
necessary.
Locate the 1/4"hex-head screws on the top of each pedestal
foot. Reach inside the pedestal and use a 1/4"hex-head
ratchet or open-end wrench to adjust the feet up or down
as needed, to level the washer/dryer.
NOTE: Make sure all four pedestal feet are in solid contact
with the oor.
When the washer/dryer is level, use a 9/16" open-end wrench
to securely tighten all four jam nuts against the pedestal.
IMPORTANT: The jam nuts must be tightened to avoid
vibration.
Reinstall pedestal drawer
Pull both drawer slides out and reassemble the drawer to
the drawer slides with the two hex-head screws.
Remove the shipping lm from the drawer.
Place the divider in the drawer at the desired
location. Close the drawer.
NOTE: Use of the divider is optional.
Not Level LEVEL Not Level
9
SÉCURITÉ DU PIÉDESTAL
Niveau Clé plate 9/16"
Pince ou pince articulée Seau
EXIGENCES D’INSTALLATION
EXIGENCES D’EMPLACEMENT
REMARQUE : Si l’ensemble de laveuse/sécheuse et du
piédestal se trouve dans un garage, il faut ajouter 3" (76 mm)
en dessous du piédestal pour que l’ensemble de laveuse/
sécheuse soit à 18" (458 mm) au-dessus du plancher du garage.
OUTILLAGE ET PIÈCES
Rassembler les outlis et pièces nécessaires avant de
commencer l’installation.
Outillage nécessaire :
Couteau utilitaire Clé à cliquet à tête
hexagonale de 1/4"
ou clé plate
Tourne-écrou de 1/4" Cliquet ou tourne-écrou à
tête hexagonale de 5/16"
Autres articles nécessaires :
Serviette Éponge
10
Pièces fournies :
Quatre vis de tôlerie n° Cloison du tiroir
12 x 3/4" à tête hexagonale
1. Vider le tiroir du piédestal
DESEMBALLAGE DU PIÉDESTAL
Préparation du piédestal pour l’installation
Ouvrir le tiroir du piédestal aussi loin que possible et vider son
contenu. L’emballage contient quatre vis de tôlerie à tête
hexagonale n° 12 x 3/4" et une cloison du tiroir.
IMPORTANT: Mettre la boîte du piédestal de côté pour pouvoir
l’utiliser pendant l’installation.
Hex-head screw
Drawer slide
3. Retirer le tiroir du piédestal
À l’aide d’un tourne-écrou de 1/4", retirer les vis à tête
hexagonale des deux glissières de tiroir et conserver les vis.
Retirer le tiroir des glissières et le mettre de côté. Réinsérer
les glissières dans le piédestal.
Les quatre cales d’espacement sont installées sur le dessus
du piédestal. Les cales réduisent les vibrations entre le
piédestal et la laveuse/sécheuse.
REMARQUE : Si des pieds sont installés sur la laveuse/
sécheuse, les retirer.
Spacer pads
2. Identier les cales d’espacement
Cales d’espacement
Glissiére du tiroir
vis à tête
hexagonale
Questo manuale è adatto per i seguenti modelli
2
Indice
Lingue:
Altri manuali Whirlpool Accessori per il bucato
Whirlpool
Whirlpool W10323246 Manuale utente
Whirlpool
Whirlpool WVP5000SQ Manuale utente
Whirlpool
Whirlpool WFP2715HW0 Manuale utente
Whirlpool
Whirlpool For use only with front load washer and... Manuale utente
Whirlpool
Whirlpool LRF4001RY Manuale utente
Whirlpool
Whirlpool 279827 Istruzioni per il montaggio
Whirlpool
Whirlpool WHP1500SCB Manuale utente
Whirlpool
Whirlpool 279787 Istruzioni per il montaggio
Whirlpool
Whirlpool W10198562A Manuale utente
Whirlpool
Whirlpool W10110902 Manuale utente
