Whispbar K945W Manuale utente
K945W
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 6 x 6 x 6 x 6
Revision No: 1A 1
Fitting Kit K945W
MAX kgs (lbs)
W/P WHD
Iveco
Daily Low Roof, 4dr Van 15-+ NZ 100 kgs (220 lbs) 100 kgs (220 lbs)
Daily Low Roof, 4dr Van 15-+ ZA 100 kgs (220 lbs) 100 kgs (220 lbs)
Daily Low Roof, 4dr Van May 15-+ AU 100 kgs (220 lbs) 100 kgs (220 lbs)
Daily Mid Roof, 4dr Van 15-+ AU 100 kgs (220 lbs) 100 kgs (220 lbs)
Daily Mid Roof, 4dr Van 15-+ NZ 100 kgs (220 lbs) 100 kgs (220 lbs)
Daily Mid Roof, 4dr Van 15-+ ZA 100 kgs (220 lbs) 100 kgs (220 lbs)
2
Fitting Kit K945W
X
A B C 1 2 3
Daily Low Roof, 4dr Van 15-+ (NZ) 1060mm 1860mm 2660mm 1050mm 1050mm 1050mm
41 3/4ths" 73 1/4ths" 104 3/4ths" 41 5/16ths" 41 5/16ths" 41 5/16ths"
Daily Low Roof, 4dr Van 15-+ (ZA) 1060mm 1860mm 2660mm 1050mm 1050mm 1050mm
41 3/4ths" 73 1/4ths" 104 3/4ths" 41 5/16ths" 41 5/16ths" 41 5/16ths"
Daily Low Roof, 4dr Van May 15-+ (AU) 1060mm 1860mm 2660mm 1050mm 1050mm 1050mm
41 3/4ths" 73 1/4ths" 104 3/4ths" 41 5/16ths" 41 5/16ths" 41 5/16ths"
Daily Mid Roof, 4dr Van 15-+ (AU) 1400mm 2300mm 3200mm 735mm 735mm 735mm
55 1/8ths" 90 9/16ths" 126" 28 15/16ths" 28 15/16ths" 28 15/16ths"
Daily Mid Roof, 4dr Van 15-+ (NZ) 1400mm 2300mm 3200mm 735mm 735mm 735mm
55 1/8ths" 90 9/16ths" 126" 28 15/16ths" 28 15/16ths" 28 15/16ths"
Daily Mid Roof, 4dr Van 15-+ (ZA) 1400mm 2300mm 3200mm 735mm 735mm 735mm
55 1/8ths" 90 9/16ths" 126" 28 15/16ths" 28 15/16ths" 28 15/16ths"
3
Fitting Kit EN
K945W
Items you will require:
●Tape measure
Pen
Flat-head screwdriver
Craft knife
Side cutters or tin snips
Hammer
8mm (3/8") punch
Cordless drill
Depth stop
Vacuum cleaner
Rust inhibitor
Small paint brush
Neutral cure silicon sealant
Rivet gun
Attention:
●Attaches with permanent tracks riveted to
roof. Bar can be removed
●Professional installation recommended.
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
4
Fitting Kit EN
K945W
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Assemble front and rear plugs to tracks.
Note: Rear plug shown in picture.
●Carefully select position on vehicle roof
making sure that your crossbar lengths will
match selected positions for the tracks.
●Apply long lengths of masking tape to
vehicle roof in both positions.
●Make sure there is no interference between
what you intend to carry with aerials,
sunroof or tailgate.
5
Fitting Kit EN
K945W
●Tracks can be fitted either parallel or
tapered to match vehicle roof shape.
●Parallel Tracks:
A1 & A2 are equal
B1 & B2 are equal
C1 & C2 are equal
D1 & D2 are equal
●Tapered Tracks:
A1 & A2 are different
B1 & B2 are equal
C1 & С2 are equal
D1 & D2 are equal
●With help from another person, carefully lay
tracks over the masking tape and mark
rivet hole positions with a pencil or pen.
●Take care not to move the tracks until the
holes are marked out.
●Use drill bit supplied, to drill rivet holes in
marked positions.
●Take care not to drill too deep.
●Vacuum and clean swarf from channel.
●Treat holes to prevent corrosion.
6
Fitting Kit EN
K945W
●Remove masking tape and apply silicon
sealant around drilled holes.
●Sit tracks on roof and line up tracks with
drilled holes.
●Insert rivets through the tracks and into
drilled holes.
●Fit pop rivet nozzle supplied with tracks to
your rivet gun.
Note: It is a standard thread to fit most rivet
guns. Use low pressure on air rivet guns.
●Ensure that the front plugs are at the front
of the track and rear plugs at the rear.
●Rivet tracks to roof.
●Slide metal T-bolt into the track channel via
the entrance on the rear end plug.
7
Fitting Kit EN
K945W
Fitment
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
8
Fitting Kit EN
K945W
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Select plastic internal block (from fitting kit)
and insert into foot.
●Repeat for all legs.
●Fit rubber pads (supplied with fitting kit) to
foot. Pad may vary in shape to that shown.
●Make sure the pad fits into the holes
underneath the foot.
9
Fitting Kit EN
K945W
●Adjust crossbar in or out to suit vehicle.
Refer to the crossbar instructions for
crossbar adjustment.
●Ensure that the crossbar is adjusted evenly
at both ends.
●Mount crossbar over metal T-bolt.
●Tighten adjusting screw to 2 Nm (1.5 ft lb)
hand tight.
●Tighten the plastic knob.
●Ensure the plastic knob is in the position
shown when fully tightened.
10
Indice
Altri manuali Whispbar Accessori per automobili
Whispbar
Whispbar K366W Manuale utente
Whispbar
Whispbar K765W Manuale utente
Whispbar
Whispbar K033W Manuale utente
Whispbar
Whispbar K193W Manuale utente
Whispbar
Whispbar K719W Manuale utente
Whispbar
Whispbar K753W Fitting Kit Manuale utente
Whispbar
Whispbar K346W Manuale utente
Whispbar
Whispbar K375W Manuale utente
Whispbar
Whispbar K333W Manuale utente
Whispbar
Whispbar K345W Manuale utente
Whispbar
Whispbar K383W Manuale utente
Whispbar
Whispbar K1003W Manuale operativo e di installazione
Whispbar
Whispbar K537W Manuale utente
Whispbar
Whispbar K350W Manuale utente
Whispbar
Whispbar K175W Manuale operativo e di installazione
Whispbar
Whispbar K059W Manuale utente
Whispbar
Whispbar K467W Manuale utente
Whispbar
Whispbar K413W Manuale utente
Whispbar
Whispbar K850W Manuale operativo e di installazione
Whispbar
Whispbar K477W Manuale utente
