Whistler WHD-100 Manuale utente
WHD-100
User Guide
HEADS UP DISPLAY
(HUD)
2
INTRODUCTION
Welcome
Thank you for choosing a Whistler product. We are
dedicated to providing products that represent both
quality and value. Please read the User Guide carefully
before using this product. If you have additional
questions, please visit the FAQ page on our website at
www.whistlergroup.com.
Customer Service
1-800-531-0004
Monday - Friday • 8:00 am - 5:00 pm CT
or visit our website
www.whistlergroup.com
3
PRODUCT INTRODUCTION
Power Switch
Setting Switch
OBDII Connection
Cable Port
Items Included:
• WHD-100 (Heads Up Display)
• Reflective Film
• OBDII Connection Cable
• Non-Slip Dash Pad
• User Guide
4
PREPARATION BEFORE INSTALLATION AND USE
Know the type of your vehicle.
The WHD-100 is intended for operation in 1996 or newer
vehicles that are OBDII compliant. To verify if your
vehicle is OBDII compliant, confirm that it has the 16-pin
OBDII plug beneath the dash. On some vehicles you
can also open the hood and look for a decal similar to
the image below.
NOTE: The vehicle OBDII port is generally located
beneath the steering wheel under the dash. Some
vehicles may have the port located behind a trim panel
in this area. Consult the vehicle Owner's Manual to
identify the OBDII location.
5
3
4
1 2
Light Sensor does
not illuminate.
• Screen Function
1. Vehicle Speed: Digital speed when vehicle is in
motion.
2. MPH: Speed is measured in Miles Per Hour.
3. RPM: Revolutions Per Minute of engine
NOTE: RPM Red area is shown for reference only
and may vary with different vehicles. Consult vehicle
Owner's Manual for specific information.
4. Light Sensor: Automatically adjusts brightness for
day or night display.
INTRODUCTION OF FUNCTIONS
6
• Initial Use
1. Connect the OBDII Connection Cable (included)
to the HUD and plug the male OBDII connector
into the vehicle OBDII port.
2. With the vehicle in PARK (or stationary for manual
transmissions), start the vehicle and power on the
HUD (slide switch on HUD near cable connection).
The HUD screen will illuminate and HUD will be
displayed as the device begins the boot-up
process.
SET UP
7
3. The HUD device will scan the vehicle OBD protocol,
and when successful will display the engine RPM
and speed (0 MPH while vehicle is stationary).
NOTE: If nothing is displayed after a few seconds,
switch OFF the HUD device and check the cable
connections to the HUD and to the vehicle OBD2 port.
Switch HUD device ON and repeat set up steps.
SET UP
The screen should look
like this once Set Up is
complete.
8
4. With the HUD power switch left ON, the device will
automatically power ON when the vehicle is started
and power OFF within a few seconds of when the
vehicle is turned OFF.
NOTE: The HUD may also be turned OFF manually
and will resume normal operation when manually
turned ON.
SET UP
9
INSTALLATION
Placing HUD On Dash
1. Once the HUD has been successfully paired with
vehicle, it needs to be properly placed on the
vehicle dash to provide easily viewed reflected
display and not to interfere with safe operation of
the vehicle.
2. Locate the preferred placement on the vehicle dash
using Non-Slip Dash Pad included.
3. Position the OBDII Connection Cable so as to not
interfere with safe operation of the vehicle.
4. Install the Reflective Film above the HUD to allow
the reflected information to be displayed and easily
seen by the vehicle driver.
5. Once the film installation position is determined,
the film may be permanently installed to the vehicle
windshield.
NOTES:
1) Vehicles vary. Installation may require temporarily
holding the Reflective Film against the windshield and
repositioning the HUD to find the correct placement of
both the HUD and film that will provide the best viewing
angle.
2) Place the non-slip dash pad on your dashboard in the
desired location. If the dash pad becomes dull or no
longer grips, simply wipe the dash pad and dashboard area
clean with a damp cloth using nothing more than clean
water.
10
INSTALLATION
To Install Reflective Film
1. Lightly spray the area of the windshield with water
where the Reflective Film is to be installed.
2. Remove the protective film marked BACK and
position the film on the windshield. (The water
spray will allow for slight repositioning to confirm
proper location above HUD.)
3. Once properly positioned, any excess water behind
the film can be removed by using a non-scratch
squeegee (not included) to squeeze the water from
behind the film and remove any air bubbles.
4. Allow any remaining moisture to evaporate before
touching the Reflective Film. After moisture has
evaporated, carefully remove the protective film
marked FRONT.
NOTE: Installation of the Reflective Film should be
done in an environment above 50ºF. Adequate time
must be allowed for moisture to evaporate to insure
proper adhesion of Reflective Film. Evaporation
time will vary depending on climate and temperature
(generally 24-48 hours). The HUD may be used
immediately, however, the Reflective Film should not be
touched until all remaining moisture has evaporated.
Indice
