Wiedamark CL-4036 Istruzioni per l'installazione

36X10W

36X10W 4

4 in

in 1

1 LED

LED

LED Wall

Wall

Wall Washer

Washer

Light

User

User Instruction

Instruction

CONTENTS

1. INSTRUCTION

INSTRUCTION

Unpacking

Introduction

AC Power

Safety Instruction

Cleaning

2. FEATURE

FEATURE

SET

SET UP

3-Pin to 5-Pin Conversion Chart

Setting up a DMX Serial Data Link

Master/Slave Fixture Linking

4. OPERATING

OPERATING

OPERATING INSTRUCTIONS

INSTRUCTIONS

Operating modes

Product overview

Program Mode & Sound Mode

Master-Slave Operation

Master-Slave Connections and Settings

DMX Mode

5. DMX

DMX

DMX CHANNEL

CHANNEL

CHANNEL SUMMARY

SUMMARY

LED

LED Wall

Wall

Wall Washer

Washer

Washer Light

Light

Light Introduction

Introduction

Unpacking:

Thank you for purchasing our products . Every unit has been thoroughly tested

and has been shipped in perfect operating condition. Carefully check the shipping carton for

damage that may have occurred during ship ping. If the carton appears to be damaged, carefully

inspect your fix ture for any damage and be sure all accessories necessary to operate the unit has

arrived intact. In the case damage has been found or parts are missing, Save the carton and all

packing materials. In the event a fixture must be returned to the factory. It is important that the

fixture be returned in the original factory box and packing.

Introduction:

The unit is a DMX intelligent LED par can. This light can be used in a stand

alone mode or connected in a Master/Slave configuration. The unit can also be controlled via

DMX controller. This light has four operating modes: Sound Active mode, stand alone mode ,

Master/Slave and DMX control mode .

AC Power

Power

Power :

This fixture has an auto-switching power supply that can accommodate a wide range

of input voltages. The only thing necessary to do before powering on the unit is to make sure the

line voltage you are applying is within the range of accepted voltages. This fixture will

accommodate between 90V and 240V AC. All fixtures must be powered directly off a switched

circuit and cannot be run off a rheostat (variable resistor) or dimmer circuit. Even if the rheostat or

dimmer channel is used solely for a 0-100% switch.

Safety

Safety Instructions:

Instructions:

• To reduce the risk of electrical shock or fire, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required volt-

age for your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken. Do not attempt to remove or break off the ground

prong from the electrical cord. This prong is used to reduce the risk

of electrical shock and fire in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it

’

s cover is removed.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6 ”(15cm) between this device and a wall.

Please read these instructions carefully, which includes important

information about the installation, usage and maintenance of this

product .

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out`

doors voids all warranties.

• During long periods of non-use, disconnect the unit

’

s main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to be walked on or pinched by

items placed upon or against them, paying particular attention to the point they exit from the unit.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 3 for cleaning details.

• Heat -The appliance should be situated away from heat sources

such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce

heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the appliance.

C. The appliance has been exposed to rain or water.

D. The appliance does not appear to operate normally or exhibits a marked

change in performance.

Caution!

There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,

doing so will void your manufacturers warranty. In the unlikely event your unit may require

service please contact us.

Cleaning:

Due to fog residue, smoke, and dust cleaning the internal and exter nal optical

lenses must be carried out periodically to optimize light output.

1. Use normal glass cleaner and a soft cloth to wipe down the

outside casing.

2. Clean the external optics with glass cleaner and a soft cloth

every 20 days.

3. Always be sure to dry all parts completely before plugging

the unit back in.

Cleaning frequency depends on the environment in which the fixture operates (i.e. smoke, fog

residue, dust, dew).

LED

LED Wall

Wall

Wall Washer

Washer

Washer Light

Light

Light Features

Features

Multi-Voltage: AC90V-245V/50-60Hz

Power: 400W

Fuse: 3A. IP Rate: IP65

LEDs: 36x10Watt 4 in 1 LEDs, Each LED have RGBW colors.

Color of LED: Red & Green & Blue & White

Lamp: 36x10Watt 4 in 1 LEDs, each LED have RGBW colors.

Beam angle: 25 degree (selectable)

Life time: 100, 000 hours RATED LEDs

Built-in power supply

Built-in 3-pin XLR serial data connection.

Control board with 4-digit display.

Light Projecting Distance: 60-80M

Color: RGBW color can be mixed to more than 16.7million kinds of color

Control: DMX512, Master-slave, stand-alone.

Channel: 4/8CH

Feature: Cast-Aluminum case, nice and wide application, less power consumption, high brightness,

Flicker free for television and film, stable performance, long life.

Function: Color combination changer of the latest hybrid technology and excellent built-in

program, Gradual, transition, and other effects

Size: 660× 300× 400mm

Packaging: 700x350x460mm (1PCS/CTN)

N. W: 16KG G.

W.:

19KG

LED

LED LED

LED

LED Wall

Wall

Wall Washer

Washer

Washer Light

Light

Light Set

Set

Set Up

Notice:

Be sure to follow figures two and three when making your own cables. Do not use the

ground lug on the XLR connector. Do not connect the cable ’ s shield conductor to the ground lug

or allow the shield conductor to come in contact with the XLR ’ s outer casing. Grounding the

shield could cause a short circuit and erratic behavior.

Figure

Figure 3

XLR Pin Configuration

Pin 1 = Ground

Pin 2 = Data Compliment(negative)

Pin 3 = Data True(positive)

3-Pin

3-Pin to

to 5-Pin

5-Pin

5-Pin Conversion

Conversion

Conversion Chart:

Chart:

Note!

Note! If you use a controller with a 5 pin DMX output connector,you will need to use a 5 pin to

3 pin adapter. The chart below details a proper cable conversion:

3-Pin

3-Pin to

to 5-Pin

5-Pin

5-Pin Conversion

Conversion

Conductor 3 Pin Female(Output) 5 Pin Male(Input)

Ground/Shield Pin 1 Pin 1

Data(-) signal Pin 2 Pin 2

Data(+) signal Pin 3 Pin 3

Not Used Do not use

Setting

Setting up

up a

a DMX

DMX

DMX Serial

Serial

Serial Data

Data

Data Link:

Link:

Master/Slave

Master/Slave Fixture

Fixture

Fixture Linking:

Linking:

1. Connect the (male) 3 pin connector side of the DMX cable to the output(female) 3 pin

connector of the first fixture.

Connect the end of the cable coming from the first fixture which will have a (female) 3 pin

connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then,

proceed to connect from the output as stated above to the input of the following fixture and so on

Operating

Operating Modes:

Modes:

You

can use the unit in either a stand alone mode or a master/slave configuration, there are 4

modes to choose from:

• Program Mode - Choose a static color, color show , color fade show, or color cycle. The speed of

the show is adjustable.

You

can also have the unit strobe in this mode.

• Master/Slave Mode- Using the Master unit, choose your desired mode or program and connect

the “Slave ”unit or units , All slaves will now follow the ” Master ” unit. But only one master.

• DMX control mode - This function will allow you to control each

individual fixtures traits with a standard DMX 512 controller

Product

Product overview:

overview:

(Diagram I )

B C D

Button Function

<FN>

Used to access the mode or to return to a previous mode

option

<UP> B Change the value of function you choosing in ascending

order

<DOWN> C Change the value of function you choosing in descending

order

<ENTER> D locate the function of which you want to change the value

Press the MODE button, you can browse all the function, such as AUTO RUN, DMX MODE,

SLAVE MODE, SOUND

While the function you want, for example, if DMX MODE, the ADDR & MODE can be adjusted.

You

can press SETUP button to catch them, if MODE, it has 6 models, press UP & DOWN to

locate it.

Program

Program Mode

Mode

Mode &

& Sound

Sound

Sound Mode:

Mode:

In Program Mode you can pick your desired factory installed program; static color, color show,

color fade, or color cycle. You can apply a strobe effect to static colors, and control the speed of

the color shows, color fade, and color cycle.

1. Plug the fixture in and press the MODE button till 01

01 static

static

static display, you are now in program

model. Press UP and DOWN to find your desired effect.

2. If you have selected a static color, press SET UP button to enter into the flash rate (F:

000-100), press UP and DOWN to adjust and select your desired flash rate.

3. When you have chosen a color show (02-17), press SET UP button, the display will show

“ S000-S100 ” , Press UP and DOWN button to adjust and set the speed. When the display

shows “ F000-F100 ” , your desired program is running in strobe effect.

4. When the display shows Sound, the unit is working in sound active mode, and the sensitivity

(SENS: 00-99) is adjustable.

Master-Slave

Master-Slave Operation:

Operation:

This function will allows you to link units together to run in a Master-Slave mode. In

Master-Slave operation one unit will act as the con trolling unit and the others will react to the

controlling units built-in programs. Any unit can act as a Master or as a Slave however, only one

unit can be programmed to act as the “Master. ”

Master-Slave

Master-Slave Connections

Connections

Connections and

and

and Settings:

Settings:

1. Daisy chain your units via the XLR connector on the rear of the unit. Use standard XLR

microphone cables to link your units to-gether. Remember that the Male XLR connector is the

input and the Female XLR connector is the output. The first unit in the chain (master) will use

the female XLR connector only. The last unit in the chain will use the male XLR connector

only.

2. Using the Master unit, choose your desired mode or program and connect the “Slave ”unit or

units.

3. Set the “ Slave ” unit(s) to the DMX address mode. They will now follow the ” Master ” unit.

DMX

DMX MODE:

MODE:

Operating through a DMX controller give the user the freedom to cre ate their own programs

tailored to their own individual needs.

1. This function will allow you to control each individual fixture ’ s traits with a standard DMX 512

controller.

2. To run your fixture in DMX mode, plug in the fixture via the XLR

connections to any standard DMX controller. Press MODE

MODE

MODE button till DMX

DMX

DMX MODE

MODE

MODE display, and

press SET UP button to enter the DMX address and DMX mode selection, and then press UP

UP or

DOWN

DOWN buttons to adjust the DMX address and DMX mode. The channels value refers to the

following channel summary.

LED

LED Wall

Wall

Wall Washer

Washer

Washer Light

Light

Light DMX

DMX

DMX Channels

Channels

Channels Summary

Summary

1．DIAGRAM

DIAGRAM

DIAGRAM I

．

DOWN

．

CONFIRM

E. DIGITAL DISPLAY WINDOW

B C D

2．HOW

HOW

HOW TO

TO OPERATE?

OPERATE?

P ress A

Abutton, there will be eight different effects.

T he first two letters stands for functions (refer to Diagram II)

The last two letters stands for DMX address, or speed,.

ou can modify it with B

Bor C

Cbutton.And press D

Dbutton for confirmation.

3．DIAGRAM

DIAGRAM

DIAGRAM II

1 d001

4 channels, address adjustable by B & C button

(001--255)

2 d.001

8 channels, address adjustable by B & C button

( 001--255)

3 CF.01 Gradual ,speed adjustable by B & C button (01 —99)

4 CC.01

C olor change fast ,speed adjustable by B & C button

(01 —99)

5 CS.01

Color Selection, W hile change color,with B & C button

button (01 —99)

6 dENo

Color combination. S peed adjustable by B or C

button(01-99)

7 bERT

8 SLRU

Slave

、

accept and control according to master

’

signal

4．DMX

DMX

DMX 4

4 CHANNELS

CHANNELS

CH 1 RED

CH 2 GREEN

CH 3 BLUE

CH 4 WHITE

5．DMX

DMX

DMX 8

8 CHANNELS

CHANNELS

CH 1 RED

CH 2 GREEN

CH 3 BLUE

CH 4 WHITE

CH 5 RED,GREEN,BLUE,WHITE 0%--100% DIMMER

CH 6 STROBE CONTROL (1-255 MORE FASTER)

CH 7 001 —031 RED

032 —095 GREEN

096 —192 BLUE

193 —254 WHITE

255 —255 RGB

CH8 COMBINATION,STAND-ALONE,COLOR MIXING.

KEY

KEY POINT

POINT

Easy to operate, friendly design, no flicker while dimmer.stable quality.

Applicable to photograph, camera,TV station ,studio room as well.

Altri manuali Wiedamark Proiettore

Wiedamark

Wiedamark MH-91 Manuale utente

Manuali Proiettore popolari di altre marche

VIZULO

VIZULO Micro Martin Guida utente

EuroLite

EuroLite LED IP FL-100 SMD Manuale utente

Cooper Wheelock

Cooper Wheelock XB12 Manuale utente

Allen + Roth

Allen + Roth 17624-000 Manuale utente

ADJ

ADJ 4 STAGE PAK Manuale utente

Cooper Lighting

Cooper Lighting EGL91SW233 Manuale utente

Max

Max 37496 Manuale utente

BEGA

BEGA 85 143 Manuale utente

Beamz

Beamz 151.226 Manuale utente

EuroLite

EuroLite LED IP FL-8 Manuale utente

Ledj

Ledj PERFORMER 36 RGB Manuale utente

Perel

Perel ELS3 Manuale utente

Perel

Perel ELS3WD Manuale utente

LumX

LumX LM 36130 Manuale utente

Xtricity

Xtricity 4-80053 Manuale utente

Stahl

Stahl 6521/4 Series Manuale utente

Ecosense

Ecosense EcoSpec Manuale utente

Ayrton

Ayrton minipanel FX Manuale utente