WilTec 61591 Manuale utente

Operation Manual

Woodturning lathe - 61591

Read and follow the operating instructions and safety information before using for the first time.

Technical changes reserved!

Due to further developments, illustrations, functioning steps and technical data can differ

insignificantly.

Updating the documentation

If you have suggestions for improvement or have found any irregularities please contact us.

http://www.WilTec.de

http://www.aoyue.eu

http://www.teichtip.de

The information contained in this document is subject to change without prior notice. o part of this

document can be copied or duplicated in another form without the prior written consent of WilTec

Wildanger Technik GmbH. The WilTec Wildanger Technik GmbH assumes no liability for any errors in

this user manual or the connection diagram.

Although WilTec Wildanger Technik GmbH has made every effort to make sure that this user manual

is complete, accurate and updated, errors cannot always be avoided. In the event of problems with

this user manual please complete and send this form back to us.

FAX-notification (+++49 2403 55592-15),

from: ________________________________________

Name: ________________

Firm:_____________________

Tel/Fax:__________________

I would like to report the following mistakes:

_______________________________ ____________________________________

Customer Service WilTec Wildanger Technik GmbH

e-mail: [email protected]

Tel:++ +49 2403 55592-0

Introduction

Thank you for purchasing this quality product. To minimize the risk of injury by means of fire or

electric shock we urge that our clients take some basic safety precautions when using this

device. Please read the operation instructions carefully and make sure you have understood its

content.

Always use a grounded power connection with the appropriate mains voltage. You can

nd the corresponding mains voltage on the type plate. If you have any doubts about the

connection being grounded, have it checked by a qualied professional. Never use a

faulty electric cable.

o not inspect the electrical part of the pressure pond lter in a wet or damp

environment or when you are wet yourself and protect it from direct sunlight. Install this

device in a safe location so that nobody can step on the cable, fall over or damage it.

isconnect the power plug before cleaning it and use only a damp cloth for cleaning.

Avoid using cleaning agents and make sure that no liquid enters the electrical part of the pump.

The electric part of the device contains no parts that can be inspected or serviced by the user. Leave

the maintenance, adjustment and repair to qualified technical personnel. In case of unauthorised

intervention the 2-year warranty is no longer valid! Keep these operation instructions safe.

http://www.WilTec.de

http://www.aoyue.eu

http://www.teichtip.de

Danger! – To reduce the risk of injury, read the operating instructions before use!

Attention! Wear hearing protection. oise exposure can cause hearing loss.

Attention! Wear a dust mask. When working with wood and other materials, harmful dust can be

generated. Material containing asbestos must not be processed.

Attention! Wear protective goggles. Sparks generated during work or splinters, chips and dust

emerging from the unit can lead to loss of visibility.

Danger! Risk of injury! Do not reach into rotating workpieces.

Direction of rotation

http://www.WilTec.de

http://www.aoyue.eu

http://www.teichtip.de

Danger!

When using electrical equipment, some safety precautions must be observed to prevent injury and

damage to property. Please read these operating instructions / safety instructions carefully. Keep

these in a safe place so that the information is available to you at all times. If you should hand over the

device to another person, please also hand over these operating instructions / safety instructions. We

accept no liability for accidents or damage caused by non-compliance with these instructions and the

safety instructions.

AFETY IN TRUCTION

The corresponding safety instructions can be found in the enclosed booklet.

Danger! Read all safety instructions and instructions. Failure to follow the safety precautions and

instructions may result in electric shock, fire and/or serious injury. Keep all safety instructions and

instructions for the future.

pecial safety instructions:

Warning: When power tools are used, basic safety precautions must be followed to eliminate the risk

of fire, electric shock and personal injury, including the following:

Always wear safety glasses and head protection, e.g. a construction helmet.

Wear tight-fitting work clothing that cannot be gripped by the rotating workpiece.

Connect the machine firmly to the substrate.

http://www.WilTec.de

http://www.aoyue.eu

http://www.teichtip.de

EQUIPMENT DE CRIPTION AND COPE OF DELIVERY

Please check the completeness of the article according to the described scope of delivery. In the case

of missing parts, please contact our Service Center or the point of sale where you purchased the de-

vice within 5 working days of the purchase of the item at the latest, presenting a valid proof of pur -

chase:

Open the packaging and carefully remove the device from the packaging.

Remove the packing material as well as packing and transport locks (if present).

Check that the scope of delivery is complete.

Check the device and the accessories for transport damage.

If possible, keep the packaging until the warranty expires.

Danger!

Device and packaging material are not children's toys! Children must not play with plastic

bags, foils or small parts! There is acute ingestion and danger of suffocation!

cope of delivery:

Woodturning lathe

Front end driver ring

Tool support

Tailstock

Hand wheel

Clamping lever (2x)

Plate (2x)

Locking grip

Wrench for pinion shaft

Face Plate

Crank handle

Hexagon key

Wrench for front end driver ring

Screw small(3x)

Washer small (6x)

Spring washer (3x)

ut small (3x)

Screw large (2x)

Washer groß (2x)

Wing nut (2x)

Washer for crank handle

Original operating instructions

Safety information

http://www.WilTec.de

http://www.aoyue.eu

http://www.teichtip.de

INTENDED U E

The woodturning lathe is only used to work wood using a suitable turning iron.

The machine may only be used for its intended purpose. Any further use beyond this is not intended.

The user/operator and not the manufacturer is liable for any damage or injury of any kind resulting

from this.

Please note that our devices are not designed for commercial, technical or industrial use. We do not

assume any warranty if the device is used in commercial, craft or industrial enterprises as well as in

equivalent activities.

TECHNICAL DATA

Rated voltage: 230 V ~ 50 Hz

Rated power: 400 Watt S2 30 min

Idling speed (engine): 1400 rpm

Spindle speed: 890/1260/1760/2600 rpm

Tip width: ca. 1000 mm

Max. lathe diameter: max. 280 mm

Protection type: IP20

Weight: ca. 23 kg

Load factor:

The load factor S2 30 min (short-time operation) indicates that the motor with a rated power of 400

watts may only be continuously loaded for the time specified on the data plate (30 min). Otherwise it

would heat up excessively. During the pause, the motor cools down again to its initial temperature.

Danger! Noise and vibration:

The noise and vibration values were determined in accordance with E 61029.

Operation

Sound pressure level LPA 61 dB(A)

Uncertainty KPA 3 dB

Sound power level LWA 74 dB(A)

Uncertainty KWA 3 dB

http://www.WilTec.de

http://www.aoyue.eu

http://www.teichtip.de

The stated values are emission values and therefore do not have to represent safe workplace values

at the same time. Although there is a correlation between emission and immission levels, it cannot be

reliably determined whether additional precautions are necessary or not. Factors that can influence the

current immission level at the workplace include the duration of the effects, the nature of the

workspace, other sources of noise, etc., e.g. the number of machines and other adjacent processes.

Reliable workplace values can also vary from country to country. However, this information should en-

able the user to make a better assessment of hazard and risk.

Wear hearing protection.

oise exposure can cause hearing loss.

Keep noise and vibration to a minimum!

Only use faultless equipment.

Service and clean the unit regularly.

Adapt your mode of operation to the device.

Do not overload the device.

Have the device checked if necessary.

Switch off the device when it is not in use.

Residual Risks

Even if you operate this power tool correctly, there are always residual risks. The following

hazards may occur in connection with the construction and design of this power tool:

1) Lung damage if no suitable dust mask is worn.

2) Hearing damage, if no suitable hearing protection is worn.

3) Damage to health resulting from hand-arm vibrations if the device is used for a long period of

time or is not properly operated and maintained.

http://www.WilTec.de

http://www.aoyue.eu

http://www.teichtip.de

Before starting the equipment

Before connecting the device, make sure that the data on the nameplate corresponds to the network

data.

Warning!

Always disconnect the mains plug before making any adjustments to the unit.

The lathe must be securely set up, i.e. it should be bolted to a workbench or other fixed under -

frame.

Before commissioning, all covers and safety devices must be properly installed.

Before connecting, make sure that the data on the nameplate correspond to the mains data of

your power supply system.

Before you retool the machine (face driver/face plate) or adjust the speed, the mains plug must al-

ways be disconnected in order to prevent unintentional switching on, e.g. by other persons.

Transport the machine by lifting it to the machine bed. Observe the weight of the machine (see

technical data) and, if necessary, call in another person for help.

Assembly

Screw the second half of the machine bed to the main frame. Use the screw, two washers, the

spring washer and the nut at each of the three bolting points.

Place the tool support on the machine bed. Screw it together with the screw, plate, washer and

the clamping lever. If the tool support is in a position where the clamping lever is too long, the

clamping lever can alternatively be replaced by the wing nut.

Screw the locking handle into the workpiece support.

Place the tailstock on the machine bed. Screw it together with the screw, plate, washer and the

tension lever. If the tailstock is in the position where the clamping lever is too long, the clamping

lever can alternatively be replaced by the wing nut.

Push the handwheel onto the tailstock spindle. Make sure that the side of the handwheel with the

grub screw is guided over the flattened part of the tailstock spindle. Tighten the grub screw with

the supplied Allen key and screw the crank handle with the washer to the handwheel.

Mount the machine on a suitable surface (e.g. workbench or similar). The lathe can be mounted

in several places. Use suitable fixing material, e.g. carriage bolts for fixing to a metal base frame.

The fixing material is not included in the scope of delivery and is available from specialist dealers.

http://www.WilTec.de

http://www.aoyue.eu

http://www.teichtip.de

Tailstock adjustment

The tailstock is adjusted after loosening the clamping lever located below the machine bed or the

wing nut.

After setting the optimum clamping pressure using the handwheel, the tailstock spindle must be

secured with the lock nut.

Adjusting the tool rest

The height of the tool rest can be adjusted after releasing the locking handle.

The adjustment of the tool support in longitudinal direction is possible after loosening the clamp-

ing lever or the wing nut below the machine bed.

The tool rest must be brought as close as possible to the workpiece but without touching it.

Warning! Make sure that the workpiece support is firmly tightened and cannot rotate into the work-

piece.

peed adjustment

Pull out the mains plug.

Loosen locking screw, open housing cover and loosen motor clamping screws. Lift the motor V-

belt to release the tension of the V-belt.

Fold the V-belt to the desired speed level (pay attention to alignment!).

The belt tension is achieved by lowering the motor, the dead weight of the motor is sufficient.

Retighten motor clamping screw after speed adjustment, close housing cover and fix with locking

screw.

A table with the corresponding speeds can be found on the inside of the housing cover.

Choosing the right speed

For new turning pieces, always start with the lowest possible speed and increase it with decreas-

ing unbalance of the turning piece.

Preselect the speed according to the cutting speed table, for noncircular workpieces start with

zero speed.

The choice of the correct speed depends on several factors when turning (e.g. size0e, unbalance,

material, etc. of the workpiece).

As a rule of thumb: non-circular workpieces, large workpieces, hard woods = low speed.

http://www.WilTec.de

http://www.aoyue.eu

http://www.teichtip.de

Conversion from face driver to face plate

Place with the wrench on the wrench surface on the spindle directly behind the face driver.

Using another wrench, loosen the face driver counterclockwise while holding the other wrench.

ow turn the face plate onto the thread of the spindle and tighten it with the wrench on the spin -

dle.

Face driver and accompanying grain tip

The face driver is used to transmit the engine power to the workpiece when turning between the

tips.

When working between the face driver and the centering point, make sure that the centering hole

is drilled sufficiently deep. The centering drill diameter should be 5-8 mm. Do not select a clamp-

ing pressure that is too high. Workpieces can become curved and break due to excessive clamp-

ing pressure.

In order to avoid thread or bearing damage, the face driver must be driven in with a rubber or

wood hammer on the face of the workpiece.

The accompanying centering point prevents the centering hole to be drilled in the workpiece from

burning out.

OPERATION

Important notes on operation

When selecting your woodturning wood, please look for knots and dry cracks. Only use wood

without cracks and without larger knots (for small knots, carefully select the contact pressure of

the turning iron).

Always check by hand that the wood to be turned is firmly seated.

Warning: Pull the mains plug!

Only use original turning irons in sharpened condition.

When turning wooden discs, do not stand in the flight circle of the workpiece.

Please use a band saw or scroll saw to cut large and unbalanced woodturning stock in the best

possible way. Large unbalance of the turning material endangers your health and the service life

of the machine.

For new woodturning pieces, always start with the lowest possible speed and increase it with in-

creasing improvement of the turning force.

Do not use wooden discs with shrinkage cracks, as there is a high risk of bursting due to centrifu -

gal force.

Observe the maximum workpiece sizes (see technical data).

In case of blocked tools: pull out the mains plug before troubleshooting!

http://www.WilTec.de

http://www.aoyue.eu

http://www.teichtip.de

Altri manuali per 61591

Indice

Altri manuali WilTec Tornio

WilTec

WilTec 61591 Manuale utente

Manuali Tornio popolari di altre marche

Kval

Kval 990-H Manuale utente

Holzmann

Holzmann VD 1100ECO Manuale utente

Grizzly

Grizzly G0632 Guida rapida

Grizzly

Grizzly G0462 Manuale utente

Grizzly

Grizzly G0709 Manuale utente

HAMAR LASER

HAMAR LASER L-700 Supplemento

Promac

Promac 941VA Manuale utente

Grizzly

Grizzly G0949G Manuale utente

Teknatool

Teknatool Nova Mercury Manuale utente

Traub

Traub TNL12.2 Manuale utente

WoodFast

WoodFast M305 Manuale utente

Milltronics

Milltronics ML Series Manuale

Milltronics

Milltronics SL6 Series Manuale

OmniTurn

OmniTurn GT-75 Manuale utente

Axminster

Axminster CQ6230A-2/910 Manuale utente

Jet

Jet JWL-1640EVS Manuale di servizio

Grizzly

Grizzly G4000 Manuale utente

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN ED1000FB Manuale utente