Wincomm WTP-8B66-15O Manuale utente
WTP-8B66-15O
User’s Manual
Version V1.0
Copyright 2016, ALL RIGHTS RESERVED.
All other brand names are registered trademarks of their respective owner
Copyright Notice
Copyright © 2015
All Rights Reserved.
Printed in Taiwan.
The information contained in this document is subject to change without any notices.
Acknowledgments
Greeting & Setup
Thank you for purchasing theWTP-8B66-15O-15O Panel PC. We wish that this unit will be durable and reliable in
providing your needs. Please follow the instructions below to ensure the unit continues to have high performance
Unpacking
After opening the carton, there will be a unit with an accessory box. Examine the contents to see if there are
damages to the unit and if all accessories are present.
Setting up
Please read this manual carefully and remember to keep this manual for future reference.
Safety Instructions & Cleaning
The unit has undergone various tests in order to comply with safety standards. Inappropriate use may be
dangerous. Please remember to follow the instructions below to insure your safety during the installation and
operating process.
Transporting & Placement of unit
1. When moving the unit on a cart; be very cautious. Quick stops, excessive forces and uneven surfaces may
cause the cart to overturn thus risking the unit to fall to the ground.
2. If the Monitor display unit does fall to the ground, immediately turn the power off and disconnect cords. Then
contact a service technician for repairs. Continual use of the unit may result cause a fire or electric shock. Also,
do not repair the unit on your own.
3. Having two or more people transporting the display unit is recommended. In addition, when installing the open
frame by suspending it also requires two or more people.
4. Before suspending the unit, make sure the material used for suspension is sturdy and stable. If not properly
suspended, the display unit may fall and cause serious injury to people standing nearby as well as to the unit
itself.
5. If you wish to mount the display unit, remember to use only the mounting hardware recommended by the
manufacturer.
Electrical and Power Source Related
1. This Monitor display unit must operate on a power source as shown on the specification label. If you are not
sure what type of power supply used in the area, consult your dealer or local power supplier.
2. The power cords must not be damaged. Applied pressure, added heat, and tugging may damage the power
cord.
3. The power cord must be routed properly when setup takes place. We advise that this aspect measure is to
prevent people from stepping on the cords or while the unit is suspended to prevent flying objects from getting
tangled with the unit.
4. Do not overload the AC outlets or extension cords. Electrical shocks or fires may occur from overloading.
5. Do not touch the power source during a thunderstorm.
6. If your hands are wet, do not touch the plug.
7. Use your thumb and index finger, grip firmly on the power cord to disconnect from the electrical socket. By
pulling the power cord, may result in damaging it.
8. If the unit is not going to be in use for an extended period of time, remember to disconnect the unit.
9. Connect the unit to a power source with the same numerical value as spec. label shown. Please use only the
power cord provided by the dealer to ensure safety and EMC compliance.
Various Factors of Environment
1. Do not insert objects into the openings.
2. Do not have liquids seep into the internal areas of the Monitor display unit.
3. Having liquids seep in or inserting objects into the unit may result in electric shocks from taking and/or short
circuiting the internal parts.
4. Do not place the Monitor display unit in the presence of high moisture areas.
5. Do not install the Monitor display unit in a wet environment.
6. Do not place near unit near heat generating sources.
7. Do not place the unit in a location where it will come in contact with fumes or steam.
8. Remember to keep the Monitor display unit away from the presence of dust.
9. If water has flow in or seep in, immediately disconnect the open frame unit. Then contact a service technician
for repairs.
Ventilation Spacing
1. Do not cover or block the openings on the top and back sides of the display unit. Inadequate ventilation may
cause overheating thus reducing the lifespan of the unit.
2. Unless proper ventilation is present, do not place unit in an enclosed area; such as a built-in shelf. Keep a
minimum distance of 10 cm between the display unit and wall.
Cleaning the unit
1. Remember to turn off the power source and to unplug the cord from the outlet before cleaning the unit.
2. Carefully dismount the unit or bring the unit down from suspension to clean.
3. Use only a dry soft cloth or clean room wiper when cleaning the LCD panel or touch screen surface. Use a soft
cloth moistened with mild detergent to clean the display housing.
4. Remember to avoid having liquids seep into the internal components.
Servicing, Repairing, Maintenance & Safety Checks
1. If the unit is not functioning properly, observe the performance level of the display closely to determine what
type of servicing is needed.
2. Do not attempt to repair the Monitor display unit on your own. Disassembling the cover exposes users’ to high
voltages and other dangerous conditions. Notify and request a qualified service technician for servicing the
unit.
3. If any of the following situations occur turn the power source off and unplug the unit. Then contact a qualified
service technician
i. A liquid was spilled on the unit or objects have fallen into the unit.
ii. The unit is soaked with liquids.
iii. The unit is dropped or damaged.
iv. If smoke or strange odor is flowing out of the open frame unit.
v. If the power cord or plug is damaged.
vi. When the functions of the unit are dysfunctional.
4. When part replacement is needed. Make sure service technician uses replacement parts specified by the
manufacturer, or those with the same characteristics and performance as the original parts. If unauthorized
parts are used it may result in starting a fire, electrical shock and/or other dangers.
Battery Installation
Follow below instructions and notice the caution for replacing and disposing of the RTC Lithium battery CR2032 for
safety consideration.
CAUTION:
There is danger of explosion, if battery is incorrectly replaced. Replace only with the same or equivalent type
recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instruction.
Version Change History
Date Version Description Remark
2016/07/28 Draft First release Ivy
2016/08/29 V1.0 Final release Ivy
2
How to Use This Manual .................................................... 3
System Overview ..................................................... 4
System View ....................................................................... 9
Setting up the System........................................................ 10
Installing System Software ............................................... 10
Installing the Drivers......................................................... 10
BIOS Setup Information......................................... 12
Appendix .............................................................. 20
A.
Jumper settings and Connectors ........ 20
Visor Assemble Instruction .......................... 38
3
How to Use This Manual
This manual is written for the system integrator, PC technician and knowledgeable PC end user. It describes how to
configure yourWTP-8B66-15O Panel PC to meet various operating requirements. The user’s manual is divided
into three chapters, with each chapter addressing a basic concept and operation of the server board.
Chapter 1: System Overview - presents what you have inside the box and gives you an overview of the
product specifications and basic system architecture for theWTP-8B66-15O Panel PC.
Chapter 2: System Installation - describes how to set up the system.
Chapter 3: BIOS Setup Information - specifies the meaning of each setup parameter, how to get advanced
BIOS performance and update to a new BIOS. Additionally, the POST checkpoint list will give you a guide for
troubleshooting.
The contents of this manual are subject to change without prior notice. These changes will be incorporated in new
editions of this manual.
Touch Chemical Resistance
4
System Overview
System
CPU Intel® Atom E3845 processor 10W
Graphic Intel® HD Graphics
AN Intel I210-IT Gigabit Ethernet x 2
Memory Dual Channel, two DDR3 SODIMM socket support up to 8GB
DDR3L-1333
Serial ATA SATA II controller (3.0Gb/sec) Port x 2
Serial port External RS232/RS422/RS485 x 1(Set BIOS, RS485 auto flow), RS232 x 1
Internal RS232 x 1
RS232 (Jumper 5V, 12V) x1
USB External USB 2.0 M12 x 4
Internal Mini-PCIE x 2(default) or USB 2.0 pinhead x 2(co-layout)
Touch x 1
USB 2.0 Pin head X 2
WDT Generates system reset; 256 segments, 0, 1, 2…25
BIOS
Brand: AMI
Flash ROM size: 64Mb
Support RTC wakeup /Wake on AN /Power on after power failure/PnP/ACPI/RTC
Press F11 to Quick boot menu.
Select First LAN port for PXE boot.
5
Display
Brand Civue
Resolution (pixel) XGA (1024 x 768 pixels)
Active Area (mm) 304.1 (H) x 228.1(V) (15.0”diagonal)
Outline Dimensions (mm) 326.5 x 253.5 x 11.528
Pixel Pitch (mm) 297x297
Display Mode Normally white
Vie Angle (H/V) 80/70
Brightness (cd/m2) 1000
Contrast Ratio 700:1
Response Time (ms) (at 25°C) Tr 5 Tf 11
Backlight ED
Weight (g) 1134
life time<Hrs> 50000
Touch Screen
Brand DMC
Glove Special glove for PCT only
Number of fingers defult setting : 1pt
Interface USB
Light Transmission 91%
Hardness Over 5H
Glass thickness 2.35mm( included adhesive sheet 1.15mm)
Active area 305x229mm
Vie ing area 308.6x232.2
Lifetime 50000000 hits
Touch limitations
Dry / Moisture
Drag Normal
Placement Angle of elevation 0∘~ 90∘
UI Design UI icon spacing & edge > mm
Gloves special glove for PCT only
Point 1pt
Touch Point Accuracy +/- 5mm. (Note)
*Note: the touch point accuracy around edge about 1.5cm = +/- 15mm(max)
6
Water drip / pouring et
Drag Medium risk of false touch
Placement Angle of elevation 0∘~ 90∘
UI Design UI icon spacing & edge > mm
Gloves special glove for PCT only
Point 1pt
Touch Point Accuracy +/- 5mm. (Note)
*Note: the touch point accuracy around edge about 1.5cm = +/- 15mm(max)
Storage
SSD 128GB 2.5" SATA SSD 3MG2-P x 1
Expansion slots
Mini-PCIe 52 pin card-edge type x 2 support half/full size (for W AN module)
External ater/dust resistant I/O (rear side)
USB 1 x M12 8pin for USB 1/2
1 x M12 8pin for USB 3/4
COM 1 x M12 8pin for COM 1/RS-232/422/485 (Default RS-232)
1 x M12 8pin for COM 2/RS-232
RS-232: TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
RS-422: Tx+, Tx-, Rx+, Rx-, GND
RS-485: Tx+, Tx-, Rx+, Rx-, GND
AN 1 x M12 8pin for AN 1
Power 1 x M12 5pin DC power connector
Po er
Power DC-In connector x 1
Power Input DC 7V~32V
Power Adapter input 100-277V~ 47 ~ 63 Hz / DC output 24V,,
Power Consumption 40.9W
Optical solutions
1. Sunlight readability by optical bonding between touch and CD
bonding thickness 1mm
transmission rate >95%.
Indice
Altri manuali Wincomm Pannello touch
Wincomm
Wincomm WLP-7B20 Series Manuale utente
Wincomm
Wincomm WLP-7821-17 Manuale utente
Wincomm
Wincomm WMP-248 Manuale utente
Wincomm
Wincomm WLP-7A20 Series Manuale utente
Wincomm
Wincomm WMP-19B Manuale utente
Wincomm
Wincomm WTP-8866-15 Manuale utente
Wincomm
Wincomm WTP-8B66 Series Manuale utente
Wincomm
Wincomm WTP-8865 series Manuale utente
Wincomm
Wincomm WMP-24C Manuale utente
Wincomm
Wincomm WTP-9A66 Series Manuale utente
