Winegard ConnecT 2.0 Manuale utente

2452462 REV8-21

For technical services:

Email [email protected] or call 1-800-788-4417

Extreme 2.0

Installation

and

Operation Manual

Parts Included:

Specifications:

WARNINGS:

(1) Extreme 2.0 outdoor unit

(1) Power Over Ethernet power

inserter (POE) indoor only

(1) L-pipe

(1) Wall mount

(1) Pipe mount

(1) Insert

(1) Hardware bag

• Dimensions: 9.35" diameter, 8" tall

• Wireless standard: 802.11a/b/g/n/ac

• Frequency band: 2.4 GHz/5 GHz

• Amplifiers: 3x3 MIMO

• Antennas: (3) 2.4 GHz/5 GHz

• Wireless security:

WPA-PSK (TKIP)

WPA2-PSK (AES)

WPA-PSK (AES) & WPA2-PSK (AES)

WPA2-PSK (AES) & WPA3 (AES)

• Port: (1) RJ45 10/100/1000

• Power rating: Switching, AC input 100-240V, 1.5A

• POE: Not intended for outdoor installation

• Read this manual carefully and completely before attempting to assemble, install, or operate this product. Winegard

recommends that a professional technician installs this equipment.

• Save these instructions.

• POE MUST BE INSTALLED INDOORS.

• DO NOT MOUNT OVER CHIMNEY OPENING.

• Never install unit upside down. Improper installation will cause product damage.

• Do not paint any portion of the Winegard Extreme 2.0. This could damage the system and will void the warranty.

• When you initially set up the Winegard Extreme 2.0, we recommend you check for software updates the first time you

connect the system to an internet signal. We also recommend you check for updates every couple of months for fixes

and added features.

Items required:

Bolts/screws for wall mount

7/16" wrench

Phillips screwdriver

Ethernet cable(s)

Installation - Outdoor/Indoor

Outdoor/Indoor Installation The Extreme 2.0 unit may be installed inside or outside. (Ethernet cable not provided – MAX 85 feet)

-OR-

Extreme 2.0

outdoor unit

POE

L-pipe

Wall mount

Pipe mount

Insert

Home

router

Connect to

POE port

LAN port to

home router

Access Point or

Bridge Modes

ONLY

Ethernet cable

L-pipe

THE POE IS INDOOR RATED ONLY.

It is not intended for outside use.

Operation - WiFi Extender Mode

IMPORTANT: Keep your/the Quick Start Guide for your records.

It contains your unique factory default SSID and password. You may also find the SSID and

password on the bottom of unit.

NOTE: Recommended browsers: Microsoft®Edge, Firefox®, Google Chrome™, or Safari ®.

WiFi Extender Mode – Increases range.

1) Turn on the WiFi-enabled device(s) that you want to connect and scan for wireless

networks. It may take a few minutes for the network to appear.

2) The label located on the front of the Quick Start Guide or bottom of the unit has the

unique default SSID and password. Select this WiFi signal from the list of wireless

networks and connect. Once the correct SSID has been selected, enter the listed

password. We recommend you set your device(s) to automatically connect with the

Winegard Extreme 2.0.

3) Once connected, open an internet browser on your device and type 10.11.12.1 into the

address bar and press ENTER. Figure 1.

This will take you to the Admin Login screen (Figure 2).

Username: admin Password: admin.

4) INTERNET ACCESS – WIFI will need to be selected. If selected move to next step.

5) Press SCAN FOR WIFI (Figure 3). This should take about one minute. The Winegard

Extreme 2.0 will display available networks by signal strength. Select the desired 2.4GHz

signal. Signal strength below 50% is not a recommended network. Click CONTINUE.

6) Enter the network password, if prompted (Figure 4). Once the Winegard Extreme 2.0

connects to the internet, the Internet Status will show Connected. This could take as

long as two minutes. You are now ready to use the WiFi and will see your paired info

under Internet Status and strength under WiFi Signal.

NOTE:The system will reboot and you

may need to reconnect to the internet.

Once connected (takes up to two

minutes), the strength of your connection

will appear under the WiFi signal.

You are now ready to use the WiFi.

Figure 1

Figure 2

Figure 4

Figure 3

WiFi 1

Operation - Access Point Mode

Access Point Mode – Provides faster throughput speeds.

1) Connect second Ethernet cable from the LAN port on your POE to your home router.

2) Turn on the WiFi-enabled device(s) that you want to connect and scan for wireless

networks. It may take a few minutes for the network to appear.

3) The label located on the front of Quick Start Guide or bottom of the unit has the unique

default SSID and password. Select this WiFi signal from the list of wireless networks

and connect. Once the correct SSID has been selected, enter the listed password. We

recommend you set your device(s) to automatically connect with the Winegard Extreme 2.0.

4) Once connected, open an internet browser on your device and type 10.11.12.1 into the

address bar and press ENTER Figure 5).

This will take you to the Admin Login screen (Figure 6).

Username: admin Password: admin.

5) INTERNET ACCESS - Select Ethernet and press SELECT (Figure 7). Your unit is

connecting and will take about 2 minutes.

NOTE: WiFi signal will stay at No signal until connected,

when using Access Point or Bridge Modes.

You are ready to use WiFi.

Figure 5

Figure 6

Figure 7

Operation - Bridge Mode 6

Bridge Mode* – Allows passthrough of your home router connections.

In this mode devices connected to the Extreme’s SSIDs/network will get the same IP subnet

as all other devices connected directly to your home router.

1) Connect second Ethernet cable from the LAN port on your POE to your home router.

2) Turn on the WiFi-enabled device(s) that you want to connect and scan for wireless

networks. It may take a few minutes for the network to appear.

3) The label located on the front of the Quick Start Guide or bottom of the unit has the

unique default SSID and password. Select this WiFi signal from the list of wireless

networks and connect. Once the correct SSID has been selected, enter the listed

password. We recommend you set your device(s) to automatically connect with the

Winegard Extreme 2.0.

4) Once connected, open an internet browser on your device and type 10.11.12.1 into the

address bar and press ENTER (Figure 8).

This will take you to the Admin Login screen (Figure 9).

Username: admin Password: admin.

5) INTERNET ACCESS - Select Ethernet and press SELECT (Figure 10).

Your unit is connecting and will take about 2 minutes.

NOTE: WiFi signal will stay at No Signal until Connected, when using Access Point

or Bridge Modes.

6) NAVIGATE TO PAGE - Select Advanced Settings.

7) Under WAN Ethernet Identifier, select Default (Figure 11).

8) From the BRIDGING drop-down menu, select BRIDGE.

9) Select CHANGE WAN ID and the system will updated.

10) Internet Status will show Connected to Ethernet (Figure 12).

11) NAVIGATE TO PAGE - Select Advanced Settings.

12) Select Restart System.

You are ready to use the internet.

Figure 8

Figure 9

Figure 11

Figure 10

Figure 12

*NOTE: Factory Reset is required to

get the unit out of Bridge Mode. You

will need to power on the unit, wait 90

seconds and then power off. Repeat 3

consecutive times. On the next power

on, the system will begin a reset, this

process could take up to 5 minutes.

Operation - 5GHz Antenna Activation 7

5GHz Antenna Activation – Allows higher speed but reduces range.

1) Turn on the WiFi-enabled device(s) that you want to connect and scan for wireless

networks. It may take a few minutes for the network to appear.

2) The label located on the front of the Quick Start Guide or bottom of the unit has the unique

default SSID and password. Select this WiFi signal from the list of wireless networks

and connect. Once the correct SSID has been selected, enter the listed password. We

recommend you set your device(s) to automatically connect with the Winegard Extreme 2.0.

3) Once connected, open an internet browser on your device and type 10.11.12.1 into the

address bar and press ENTER (Figure 13).

This will take you to the Admin Login screen (Figure 14).

Username: admin Password: admin.

4) INTERNET ACCESS – WIFI will need to be selected. Press SCAN FOR WIFI (Figure 15).

5) Enter the network password, if prompted (Figure 16). Once the Winegard Extreme 2.0

connects to the internet, the Internet Status will show CONNECTED. This could take as

long as two minutes. You are now ready to use the WiFi and will see your paired info in

Internet Status and strength in WiFi Signal.

Figure 13

Figure 14

Figure 16

Figure 15

Operation - 5GHz Antenna Activation (continued)

5GHz Antenna Activation – continued from previous page

6) Under NAVIGATE TO PAGE, select Local Network Settings

from the drop-down menu (Figure 17).

7) Under 5 GHz Network Settings, select ENABLE (Figure 18).

8) Select CONTINUE at bottom of screen.

9) You will be directed back to the Status page and close out

screen (Figure 19).

10) On your device (phone, tablet, etc.), go to Settings/WIFI and you

will now see the units 5GHz SSID broadcasting and select for

use (Figure 20).

11) Select the 5GHz connection and enter the password from the

Quick Start Guide or bottom of unit to connect.

You are now ready to use internet.

Figure 17 Figure 18

Figure 19 Figure 20

Operation - Guest Network

Guest Network -

From the Status Screen

1) Under NAVIGATE TO PAGE, select Local Network Settings

from the drop-down menu (Figure 21).

2) On the next screen, select ENABLE under Guest Network

Settings (Figure 22).

3) Give the guest network an easily recognizable name.

4) Enter a password - If you use a simple password, it is

recommended that the guest network be disabled when

not in use. Select CONTINUE (Figure 22).

5) You will be directed back to Status page and can now close out

the screen (Figure 23).

Your guests are now ready to use the WiFi.

Figure 21 Figure 22

Figure 23

Operation - NAVIGATE TO PAGE (Screens)

Page Summary -

The following screens are available under the NAVIGATE TO PAGE screen:

1) Local Network Settings - Used to select your WiFi connection, enable 5GHz connection,

change passwords, enable Guest Network, rename network ID’s and change security type.

2) Advance Settings - Used to set up Bridge Mode (Figure 25).

3) Saved WiFi Networks - Used to connect or delete stored networks.

4) Network Activity - Used to view connected devices and network traffic (Figure 24).

5) Update Software - Used to check for latest software updates, updating software, and

restoring to factory configuration (Figure 26).

6) Support - Key unit information, Winegard phone support number, email support address,

Save Log function, Test Speed and Test Connectivity (Figure 27).

7) About - Contains model number, software version, bootloader version, serial number,

MAC address and IP.

Figure 26

Figure 24

Figure 25 Figure 27

Altri manuali per ConnecT 2.0

Indice

Altri manuali Winegard Antenna TV

Winegard

Winegard HD9095P Manuale utente

Winegard

Winegard SK-3005 Manuale utente

Winegard

Winegard SK-7003 Mount Manuale utente

Winegard

Winegard Carryout GM-MP1 Manuale utente

Winegard

Winegard BMK-300 Manuale utente

Winegard

Winegard DuraSAT Manuale utente

Winegard

Winegard Freevision FV-HD30 Manuale utente

Winegard

Winegard RoadTrip Minimax RT8000S Manuale utente

Winegard

Winegard Trav'ler Pro SK2DISH Manuale utente

Winegard

Winegard GS-2200 Manuale utente

Winegard

Winegard GM-1518 Manuale utente

Winegard

Winegard RoadStar RS-3000 Manuale utente

Winegard

Winegard RS-1500 Manuale utente

Winegard

Winegard AIR 360+ Manuale utente

Winegard

Winegard SENSAR GS-2200 Manuale utente

Winegard

Winegard SENSAR VM-2200 Manuale utente

Winegard

Winegard RoadTrip SDi Manuale utente

Winegard

Winegard SK-1000 Manuale utente

Winegard

Winegard Pathway X2 for Dish Manuale utente

Winegard

Winegard SK-3005 Manuale utente

Winegard

Winegard SK-3005 Manuale utente

Winegard

Winegard SENSAR VM-1000 Manuale utente

Winegard

Winegard MS-1002 Manuale utente

Winegard

Winegard FreeVision FVHD45C Manuale utente

Manuali Antenna TV popolari di altre marche

KVH Industries

KVH Industries TracVision HD11 Manuale utente

RCA

RCA ANT310E Manuale utente

Labgear

Labgear LAB450K Manuale utente

Radio Shack

Radio Shack VU-110XR Manuale utente

BAS

BAS REMO BAS X3174 MIDI Manuale utente

Monoprice

Monoprice DA-8000 Manuale utente

TracVision

TracVision A5 Manuale utente

Alcad

Alcad 900 Series Manuale utente

Mohu

Mohu Leaf 50 Manuale utente

Emos

Emos DTV-4 Manuale utente

IKUSI

IKUSI mini FLASHD Manuale utente

Maxview

Maxview 18 Element Manuale del proprietario

Gogen

Gogen DA 553 Manuale utente

Philips

Philips SDV6120/10 Manuale utente

Philips

Philips SDV2210 Manuale utente

SLX

SLX 27887V Manuale utente

nedis

nedis ANIR2512GY700 Manuale utente

Crest Audio

Crest Audio SGA05329 Manuale utente