Winmate ARM-11 HMI Series Manuale utente
WinMate Communication INC
.
ARM-11 HMI Series Panel PC
Samsung-6410 Series SBC, Low Power, High
Performance Design with AR -11 Series
Platform, TFT LCD, RS232, RS422/485 and 10/100
base-T Ethernet.
User Guide Version 1.0
ARM-11 HMI Series PPC User’s Manual
2
Revision History
Version
Date Note
1.0 2010.09.22
First Version
Package List
Before using this Digital Signage Evaluation Kit, please make sure that all the items listed below
are present in your package
1. Box (Packaging)
2. 1 x AR -11 Series H I Panel PC Unit
3. 1 x BSP, SDK, I G and User’s manual CD
4. 1 x AR -11 H I User’s anual
5. 1 x Screw Type Power Supply 100-240 Vac / 12Vdc, 15W
ake sure that all of the items listed above are present. Do not attempt to apply power to the
system if there is damage to any of its components.
ARM-11 HMI Series PPC User’s Manual
3
FCC Statement
This device complies with part 15 FCC rules. Operation is subject to the following two
conditions
：
•This device may not cause harmful interference.
•This device must accept any interference received including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a class "a" digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference at
him own expense.
Copyright Notice
ALL RIGHTS RESERVED. No part of this document may be reproduced, copied, translated, or
transmitted in any form or by any means, electronic or mechanical, for any purpose, without
the prior written permission of the original manufacturer.
Trademark Acknowledgement
Brand and product names are trademarks or registered trademarks of their respective
owners.
ARM-11 HMI Series PPC User’s Manual
4
Disclaimer
We reserve the right to make changes, without notice, to any product, including circuits
and/or software described or contained in this manual in order to improve design and/or
performance. We assume no responsibility or liability for the use of the described product(s),
conveys no license or title under any patent, copyright, or masks work rights to these
products, and makes no representations or warranties that these products are free from
patent, copyright, or mask work right infringement, unless otherwise specified. Applications
that are described in this manual are for illustration purposes only. We Communication Inc.
makes no representation or warranty that such application will be suitable for the specified
use without further testing or modification.
arranty
We warrant that each of its products will be free from material and workmanship defects
for a period of one year from the invoice date. If the customer discovers a defect, We will, at
its option, repair or replace the defective product at no charge to the customer, provided it
is returned during the warranty period of one year, with transportation charges prepaid.
The returned product must be properly packaged in it’s original packaging to obtain
warranty service.
If the serial number and the product shipping data differ by over 30 days, the in-warranty
service will be made according to the shipping date. In the serial numbers the third and
fourth two digits give the year of manufacture, and the fifth digit means the month (e. g.,
with A for October, B for November and C for December).
For example, the serial number 1W07Axxxxxxxx means October of year 2007.
ARM-11 HMI Series PPC User’s Manual
5
Customer Service
We provide service guide for any problem as follow steps
：
First, contact with your
distributor, sales representative, or our customer service center for technical support if you
need additional assistance. You may have the following information ready before you call
：
•Product serial number
•Peripheral attachments
•Software (OS, version, application software, etc.)
•Description of complete problem
•The exact wording of any error messages
In addition, free technical support is available from our engineers every business day. We
are always ready to give advice on application requirements or specific information on the
installation and operation of any of our products. Please do not hesitate to call or e-mail us.
Safety Precautions
•Warning!
Always completely disconnect the power cord from your chassis whenever you
work with the hardware. Do not make connections while the power is on. Sensitive
electronic components can be damaged by sudden power surges. Only experienced
electronics personnel should open the Player chassis.
•Caution!
Always ground yourself to remove any static charge before touching the CPU card.
odern electronic devices are very sensitive to static electric charges. As a safety
precaution, use a grounding wrist strap at all times. Place all electronic components
in a static-dissipative surface or static-shielded bag when they are not in the chassis.
ARM-11 HMI Series PPC User’s Manual
6
Safety and arranty
1.
Please disconnect this equipment from any AC outlet before cleaning. Do not use liquid
or spray detergents for cleaning. Use a damp cloth.
2.
For pluggable equipment, the power outlet must be installed near the equipment and
must be easily accessible.
3.
Keep this equipment away from humidity.
4.
Put this equipment on a reliable surface during installation. Dropping it or letting it fall
could cause damage.
5.
The openings on the enclosure are for air convection. Protect the equipment from
overheating. DO NOT COVER THE OPENINGS.
6.
ake sure the voltage of the power source is correct before connecting the equipment
to the power outlet.
7.
All cautions and warnings on the equipment should be noted.
8.
If the equipment is not used for a long time, disconnect it from the power source to
avoid damage by transient over-voltage.
9.
Never pour any liquid into an opening. This could cause fire or electrical shock.
10.
Never open the equipment. For safety reasons, only qualified service personnel should
open the equipment.
11.
If any of the following situations arises, get the equipment checked by service personnel:
A. Liquid has penetrated into the equipment.
B. The equipment has been exposed to moisture.
C. The equipment does not work well, or you cannot get it to work according to
the user’s manual.
D. The equipment has been dropped and damaged.
E. The equipment has obvious signs of breakage.
12.
Do not leave this equipment in an uncontrolled environment where the storage
temperature is below -20° C (-4°F) or above 60° C (140° F). It may damage the
equipment.
ARM-11 HMI Series PPC User’s Manual
7
Table of Contents
1 GENERAL INFOR ATION.................................................................................................8
1.1
Introduction .................................................................................................8
1.2
Features .......................................................................................................9
1.3
Dimension and Overview............................................................................10
1.4
Specifications .............................................................................................12
1.5
System Block ..............................................................................................13
1.6
AR -11 Series LCD Selection Table.............................................................13
2 Getting Started..............................................................................................................14
2.1
Input / Output Devices ...............................................................................14
2.2
Starting the Panel PC ................................................................................14
3
Installation User Gui e for SMDK6410 (WinCE6.0 R3)..............................................15
3.1 Overview...................................................................................................15
3.2 Copying BSP an Setting up Visual Stu io 2005 ......................................16
3.3 Creating a New OS Design ........................................................................18
3.4 Buil ing OS Image – Without KITL...........................................................23
4 H I series Panel PC ounting Guide ...........................................................................35
4.1
VESA Mount ..............................................................................................35
4.2 Panel Mount (Clip Design):.......................................................................37
5
Services/ Updates.........................................................................................................39
5.1
H I Official website ...................................................................................39
5.2
Company information.................................................................................39
ARM-11 HMI Series PPC User’s Manual
8
1 GENERAL INFORMATION
1.1 Introduction
The AR -11 H I Series PPC model is compact platform without redundant functions,
which have been designed for small-sized operator interface applications. They have 5.7” VGA
LED backlight and 7" WVGA LCD display which is a cost effective choice for a limited budget. Its
RISC kernel, the Samsung 6410 processor consumes minimum power without sacrificing
performance. The AR -11 H I Series PPC has 10/100Base-T Ethernet port and WIFI 802.11
b/g(Optional) offering solid communication ability and comes bundled with a Windows CE and
Linux 2.6.2 that supports Thin-Client solutions. The built-in Windows CE6.0 and Linux 2.6.2 OS
platform lets AR -11 H I Series PPC become an Open H I solution for system integration.
AR -11 H I Series PPC
ARM-11 HMI Series PPC User’s Manual
9
1. Features
(1) Samsung-6410 Processor on board
(2) 5.7” VGA(640 x 480) LCD(LED backlight) , 7" WVGA(800 x 480) LCD(CCFL backlight)
(3) Super slim and compact design with metal housing
(4) Fanless cooling system
(5) E A4/IP65 compliant front panel
(6) Built-in NAND flash memory
(7) One Standard SD card slot
(8) RS232, RS422/485 and Ethernet for external communication.
It can even browse web sites using the internal browser, which is useful for displaying
diagnostic data or even remote control panels through a web interface.
Depending on which AR -11 H I Series PPC features you choose to access, it can be
used for anything from a user interface panel to the main controller for your automation
equipment.
ARM-11 HMI Series PPC User’s Manual
10
1.3 Dimension and Overview
1.3.1 Dimension
R05SA 0-IPD1HM
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Winmate Pannello touch
Winmate
Winmate 7'' S-Series Manuale utente
Winmate
Winmate W27FA3S-CHC1 Manuale utente
Winmate
Winmate R15IH3S-67A3HB Manuale utente
Winmate
Winmate R19IHAT-66EX Manuale utente
Winmate
Winmate W22IK3S-SPA369 Manuale utente
Winmate
Winmate W04FA3S-EHT1 Manuale utente
Winmate
Winmate IP69K Stainless P-Cap Manuale utente
Winmate
Winmate W05TA3S-PCT3AC Manuale utente
Winmate
Winmate G-WIN Slim IP65 Manuale utente
Winmate
Winmate GC Series Manuale utente
Winmate
Winmate R15IH3S-SPC369 Manuale utente
Winmate
Winmate R15IB7T-POC3 Manuale utente
Winmate
Winmate W07IB3S-EHT1 Manuale utente
Winmate
Winmate R15IB3S-PCC3-PoE Manuale utente
Winmate
Winmate W15IB3S-PTA3 Manuale utente
Winmate
Winmate B Series Manuale utente
Winmate
Winmate R15IH3S-SPC3 Manuale utente
Winmate
Winmate W07IB3S-GCM1(HB) Manuale utente
Winmate
Winmate G-WIN W07RK3S-GCT1 Manuale utente
Winmate
Winmate R15IW3S-SPC3 Manuale utente
