Wirepath WP-PS Series Manuale utente
WPS-PS
POWER
SUPPLIES
INSTALLATION AND USERS MANUAL
Review manual thoroughly before
installation. Retain for future reference.
WP-PS9-12VDC -10A WPS-PS9-12VDC -10AUL
WPS-PS9-24VAC -12A WPS-PS18-12VDC-18A
WPS-PS18-12VDC-18AUL
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of re or electric shock, do not expose this apparatus in or near rain
or moisture.
1. Read and keep these instructions for future reference.
2. Do not use this apparatus near water.
3. Clean only with a dry cloth.
4. Do not block any ventilation openings. Install according to manufacturer’s instructions.
5. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus
(Including ampliers) that produce heat.
6. Do not override the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades - one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong is provided for your safety. If the provided
plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet.
7. Protect the power cord from being walked on or pinched particularly at plug, convenience
receptacles, and the point where it exits from the apparatus.
8. Only use attachments/accessories specied by the manufacturer.
9. To completely disconnect this equipment from the AC mains, disconnect the power supply cord
plug from the AC receptacle.
10. This is CLASS II apparatus with double insulation, and no protective earth provided.
The lightning ash with arrowhead
symbol, within an equilateral triangle, is
intended to alert the user to the presence
of un-insulated dangerous voltage within
the product’s enclosure that may be of
sufcient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an
equilateral triangle is intended to alert the
user to the presence of important
operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.
CAUTION
CAUTION: TO REDUCE THE RISK OF
ELECTRICAL SHOCK.
DO NOT REMOVE COVER. NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
CAUTION
CAUTION: TO REDUCE THE RISK OF
ELECTRICAL SHOCK.
DO NOT REMOVE COVER. NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Important Note: Do Not connect AC power to the WPS-PS until all connections
to the outputs are made. Disconnect power when making any connections to
the WPS-PS.
TABLE OF CONTENTS
1 Product Overview................................................................4
1.1 Packing List ........................................................................4
1.2 Features..............................................................................4
2 Connections and Controls..................................................5
3 Installation............................................................................6
3.1 Mounting............................................................................6
3.2 Wire Access Holes .............................................................6
3.3 Connecting........................................................................6
4 Specications ......................................................................7
5 Warranty ...............................................................................7
6 Contacting Technical Support ...........................................7
WPS-PS Power Supplies Installation Manual
4
1 PRODUCT OVERVIEW
1.1 Packing List
(3) Rubber grommets
(2) Keys
(1) IEC power cord and clip (Non UL Versions)
(1) Manual
(10) Spare glass fuses in UL versions
1.2 Features
• (9) Outputs with LED Status (WPS-PS9-xxx-xx models)
• (18) Outputs with LED Status (WPS-PS18-xxx-xx models)
• Locking Cabinet Prevents Unwanted Access
• Power Switch located securely inside the locked box
• Electronically Resettable PTC Fuses per Channel (Non UL Versions)
• Glass Fuses per Channel (UL Versions)
• 48” IEC Power Cord with IEC clip on non-UL versions
• CE, and FCC Certied
• UL Certied (WPS-PS9-12VDC-10AUL and WPS-PS18-12VDC-18AUL only)
WPS-PS Power Supplies Installation Manual
5
© 2012 Wirepath Surveillance
2 CONNECTIONS AND CONTROLS
I
o
3
4
1
2
5
9
10
11
12
13
8
6
7
1. Channel fuses - Glass (UL Versions) or PTC
2. Status LEDs
3. +Volt (Positive) Outputs
4. -Volt Common (Negative) Outputs
5. Power Switch
6. IEC Locking Clip Loops (non-UL versions only)
7. IEC Power Input
8. Main Power Fuse
9. +Volt (Positive) Main Input
10. Spare Power Fuse (Glass Fuse Versions)
11. -Volt (Negative) Main Input
12. Cooling Fan (18 Channel Models Only)
13. Main Power Supply
Note:
• WPS-PS18 models will have 2 boards with 9 connections each.
• AC Versions have Torodial Power Supply
WPS-PS Power Supplies Installation Manual
6
3 INSTALLATION
3.1 Mounting
1. Locate wall studs using a stud nder (not included).
2. Position the provided template on the wall in the desired location of the WPS-PS. If the location
does not allow for this, use a wall molly or anchor with the appropriate weight rating for the WPS-PS.
3. Level the template and mark the wall with the screw locations. The bottom 2 holes are provided
if additional support is needed; mark these locations only if support on the bottom is required. See
Step 6 below.
4. Install the screws into the marked locations. Note that the screw heads CANNOT extend more than
½” from the wall or shorting to the internal boards may occur.
5. Slide the WPS-PS onto the install screws.
6. For additional support, a screw can be inserted into the lower right mounting hole. Some models
also have a mounting hole on the lower left that can be used, but it not a requirement.
3.2 Wire Access Holes
Once mounted on the wall, power leads for the devices can be run through the access holes located
at the top of the enclosure. Rubber grommets have been included to protect the wires running
through these holes.
Additionally, 1/2″ trade size piping can be connected for installations where piping is being used.
3.3 Connecting
Important Note: Do Not connect AC power to the WPS-PS until all connections to the outputs are
made. Disconnect power when making any connections to the WPS-PS.
1. Run power lead wires through the access holes located at the top of the enclosure.
2. Connect the positive lead from the device to the +Volt output terminal for each device.
3. Connect the negative lead from the device to the –Volt output terminal for each device.
4. Once all connections are made, the AC input can be connected.
5. Attach the included power cord clip to the loops by the power cord and clip onto the power cord
to secure.
WPS-PS Mounting Template
CAUTION
CAUTION: TO REDUCE THE RISK OF
ELECTRICAL SHOCK.
DO NOT REMOVE COVER. NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
WPS-PS Power Supplies Installation Manual
7
© 2012 Wirepath Surveillance
5 WARRANTY
5-Year Limited Warranty
This Wirepath™ product has a 5-Year Limited Warranty. The warranty includes parts and labor repairs
on all components found to be defective in material or workmanship under normal conditions of use.
This warranty shall not apply to products which have been abused, modied, disassembled or improp-
erly installed. Products to be repaired under this warranty must be returned to Wirepath™ Surveillance
or a designated service center with prior notication and an assigned return authorization number
(RA).
6 CONTACTING TECHNICAL SUPPORT
Phone: (866) 838-5052
Email: [email protected]
4 SPECIFICATIONS
WPS‐PS9‐12VDC‐
10A
WPS‐PS9‐12VDC‐
10AUL
WPS‐PS9‐24VAC‐
12A
WPS‐PS18‐12VDC‐
18A
WPS‐PS18‐12VDC‐
18AUL
Input 120VAC/60Hz 120VAC/60Hz 120VAC/60Hz 120VAC/60Hz 120VAC/60Hz
Output 12VDC10A 12VDC10A 24VAC12A 12VDC18A 12VDC18A
Channels 9 9 9 18 18
TotalPower 120W 120W 288W 218W 216W
MaxChannel
Power
12VDC/2A 12VDC/2A 24VAC/2A 12VDC/2A 12VDC/2A
FuseType PTC Glass PTC PTC Glass
Dimensions
(HxWXD)
8.25"Hx10.125"
Wx3.5"D
8.25"Hx10.125"
Wx3.5"D
8.25"Hx10.125"
Wx3.5"D
8.25"Hx10.125"
Wx3.5"D
8.25"Hx10.125"
Wx3.5"D
Weight 5.1lbs 5.1lbs 9lbs 5.5lbs 5.5lbs
Certifications CE,FCC CE,FCC,UL CE,FCC CE,FCC CE,FCC,UL
120417-1455
© 2012 Wirepath Surveillance
Questo manuale è adatto per i seguenti modelli
5
Indice
Altri manuali Wirepath Alimentazione elettrica
