Witek System MIS-200BE Manuale utente

ITEK

SYSTEM

INC

MIS-200BE

INTRALOT

Scanner

User’s Guide

NOTICE

1. Witek System Inc. reserves the right to make changes to the contents of

this publication without prior notice.

2 Witek System Inc. reserves the right to make changes to equipment

and specifications without obligation or notification.

3 Some equipment nomenclature and abbreviations used here may

differ from that contained in other Witek publications

4 Witek System Inc. will not be held responsible for any accidents for

damage caused by procedures not in compliance with those in this

publication, or by actions that did not heed to the cautions.

5 This publication, or parts thereof, may not be reproduced in any

form without prior written permission of Witek System Inc.

Unauthorized use or distribution of this publication is prohibited.

Information to the user

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate the equipment.

Important safety Instructions

This manual describes important details for users to use this product safely and correctly.

Read this manual thoroughly before you start using this product. Be sure to read and fully

understand the Safety Precautions in this manual, in particular. In addition, keep this manual

handy during use of this product, so that you can refer to it quickly when necessary.

The following instructions pertain to the risk of fire, electric shock or bodily injury. Please

read all of these instructions carefully.

1 Save these instructions for later use.

2 Follow all of the instructions and warnings marked on this product or included in this

manual.

3 Do not use this scanner on an unstable cart, stand or table. The product may fall, causing

serious damage to the product.

4 Don’t use this product on a bed, sofa, rug or other similar surface. This product should

never be placed near or over a radiator or heat register.

5 Never push objects of any kind into the scanner through the case openings, as they may

touch dangerous voltage points or short out parts that could result in a fire or electrical

shock. Never spill liquid of any kind on the product.

6 This scanner should only be connected to the + 24V / min. 2.5A DC power source or

designated power adapter indicated on your scanner information label. If you are not

sure of the type of power source available, consult your dealer or local power company.

Only connect this scanner to a power outlet that matches the power requirements of this

scanner.

7 Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

8 Do not use this scanner near water.

9. Do not touch the power plug or USB bus power cable with wet hands. Doing so might

cause electric shock.

10. A damaged power cable or USB bus power cable may cause fire or electric shock. Do

not place heavy objects on the power or USB bus power cable, or pull, bend, twist, heat,

damage or modify the cable. Do not use damaged power or USB bus power cables or

power plugs. Do not use the power cable when the wall socket is loose.

11. Use only the specified Power, USB bus power, and interface cables. Failure to use the

correct cables might cause electric shock and equipment failure.

12. If you detect heat coming from the device or detect other problems such as smoke,

strange smells or noises, immediately turn off the scanner and then disconnect its power

plug from the power outlet, or unplug the USB bus power cable from the computer.

Make sure that the smoking has stopped, and then contact an authorized Witek scanner

service provider.

13. Do not place heavy objects on the scanner or use the top surface of the scanner for

performing other work. Improper installation might cause injuries.

14. When the scanner is not used for a long period, be sure to disconnect the power plug

from the power outlet, or disconnect the USB bus power cable from the computer for

safety. Not doing so might cause electric shock or fire.

15. Do not insert or drop metal or flammable foreign objects in to the scanner.

Do not scan wet documents or documents with paper clips or staples.

Do not splash or allow the scanner to get wet.

16. To avoid injuries, do not place the scanner in an area where small children may be able

to reach.

17. Do not move the scanner with the power and interface cables connected as this might

damage the cables, causing fire, electric shock or injuries. Before moving the scanner, be

sure to disconnect the power plug from the power outlet, and disconnect interface cables

as well. Also, make sure that the floor is free of obstructions.

18. Avoid getting a sleeve, necktie, or hair caught up in any scanner mechanism when

scanning as this may cause injuries.

19. Install the scanner away from strong magnetic fields and other sources of electronic

noise. Also, protect the scanner from static electricity as this might cause the scanner to

malfunction.

20. Do not use the scanner immediately after moving it from a cold place into a warm room.

This may cause condensation, which might lead to scanning errors. Let the device dry

about one or two hours before you use it.

Maintenance

Repairs should be done by properly trained repair technicians. When this product needs

servicing, please contact the authorized Witek Image Scanner service provider.

If the product does not operate normally, adjust only those controls that are covered by the

operating instructions. Improper adjustment of other controls may result in damage and may

require extensive repair work to restore the product to normal operation.

Unplug this product from the main power outlet and call for service under any of the

following conditions:

a If the power cord or plug is damaged or frayed.

b If liquid has been spilled into the product.

c If the product has been exposed to rain or water.

d If the product has been dropped.

e If the product exhibits a distinct change in performance, indicating a need for service.

Stop

If you ever have to remove the scanner cover, observe the following precautions :

a The power supply cord must be unplugged before the scanner cover is removed.

b Once removed, the cover must be replaced and screwed in position before the power

supply cord is plugged back in.

CONTENTS

1. Before you start using the scanner

1.1 Unpacking

1.2 Part Identifications

1.3 Connecting the Cables

1.4 Driver Installation

2. Installation Specifications

3. Using the scanner

3.1 Basic Flow of Operations

4. Troubleshooting

4.1 Clearing Paper Jams

4.2 Troubleshooting check list

5. Cleaning the inside of the Scanner

6. Dimension

7. Repair

1. Before you start using the scanner

1.1 Unpacking

When you unpack the scanner package, find the packaging list first, and then make sure that

the MIS-200BE and all items in the packaging list are present. If anything is missing or

damaged, contact the dealer where you purchased the product.

1.2 Part Identifications

This section describes the names of parts and their functions.

■ Front View

■ Rear View

Paper Entrance

load the documents to be scanned on

this part.

Jam Removal Open Cover

open the cover to remove paper jam

Paper Outlet

paper out

Paper Guide(ears)

adjust the paper width to scan

USB Connector

Power Connector

Power Switch

■ Use the following cables(Options)

The Power cable (Option) is a combination of

the AC adapter and AC cable.

USB bus power cable(Option)

* additional cable option : Power Y cable (compatible with microlot power source)

■ USB Interface

Pin Signal Descriptions

1 +5V +5V

2 Data - Scanner transmit data line

3 Data + Scanner transmit data line

4 GND System Ground

1 2

1.3 Connecting the cables

Connect the MIS-200BE scanner to a power supply in either of two ways below: First, connect

to a power supply, and then connect to a host terminal with the USB cable.

Be sure to use the supplied AC adapter and AC cable.

Be sure to use the supplied USB cable. The operation with any

commercially available USB cable is not guaranteed.

If only the USB cable is used, the MIS-200BE does not operate. Be

sure to use two types of cables, the power and USB cables, to

connect the MIS-200BE to a host terminal.

Connect the Power cable before connecting the USB cable

When connecting to a USB hub, be sure to use the first stage USB

hub that is closest to the computer. If you use the second or later

hub stages, the scanner may not operate properly.

When connecting with a USB 2.0 cable, make sure that the USB

port to connect to and hub must be USB 2.0-compliant.

Attention

Host

Terminal

USB port

1.4 Driver Installation

■ Before Installing the SDK & Driver for MIS-200BE

Before Installing the SDK & Driver for MIS-200BE, perform the following

preparations. :

1. Check your system

The system requirements for the MIS-200BE are as follows

One of the following operating system is required :

Windows 2000

Windows XP

Embedded XP

Linux

Host terminal

* For Windows 2000,Windows XP and Linux :

Recommended: Intel® Celeron® M 430 1.73 GHz or higher

Minimum: Intel® Pentium® III 600 MHz or higher

* USB port (USB 2.0/1.1)

RAM

* For Windows 2000 and Windows XP:

Recommended: 512 MB or more

Minimum: 256 MB or more

Free disk space

Minimum100 MB

2. Make sure that the MIS-200BE is not yet connected to your host terminal.

3. Start your computer.

Log on as a user with "Computer administrator" privileges.

4. Exit all programs and close all windows.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Witek System Scanner

Witek System

Witek System SX600 Manuale utente

Manuali Scanner popolari di altre marche

Plustek

Plustek Scanner Manuale utente

Z/I Imaging

Z/I Imaging PhotoScan 2001 Manuale utente

Renkforce

Renkforce DS100-5M Manuale utente

Image Access

Image Access WideTEK A2 Manuale utente

Canon

Canon imageFORMULA CR-120N Manuale utente

Fujitsu

Fujitsu FI-4860C2 Manuale utente

GeoSlam

GeoSlam ZEB Horizon Istruzioni per l'installazione

Kodak

Kodak i5800 Scanner Manuale utente

Kodak

Kodak i7300 Manuale utente

Revopoint

Revopoint POP Manuale utente

Fujitsu

Fujitsu fi-4860C Manuale utente

Eddyfi Technologies

Eddyfi Technologies Floormap X Manuale utente

Faselase

Faselase F6 Manuale utente

Fujitsu

Fujitsu CardMinder Manuale utente

Uniden

Uniden BC340CRS Manuale utente

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Manuale utente

Mustek

Mustek PageExpress 4800 Pro Manuale utente

Optex

Optex 750830 Manuale utente