Witura WT-1011RC IP 65 Manuale utente

T-

-1

User Manual

Setting Instructions

WT-1011RC IP65 GSM Remote Controller

And Alarm S

stem

WT-1011RC IP65 – USER MANUAL – Rev.1.6 – Technical Support: [email protected]

WITURA CORPORATION SDN BHD

1) 1 pc IP65 Enclosure

2) 1 pc WT-1011RC Main Board with GSM Module mounted

3) 1 pc Battery Backup

4) 1 pc GSM Antenna

1. Introduction………………………………………………………………………………………………………………3

2. Features………………………………………………………………………………………………………………………3

3. Characteristic……………………………………………………………………………………………………………3

4. Installation Instructions………………………………………………………………………………………………6

5. WT-1011RC Programming Instructions ……………………………………………………………9

5.1 Programming the Administrator Numbers ……………………………………………………………………9

5.2 Access Control for Administrator……………………………………………………………………………………10

5.3 Programming the Guest List………………………………………………………………………………………..…10

5.4 Output Settings………………………………………………………………………………………………………………11

5.5 Input Settings…………………………………………………………………………………………………………………15

5.6 Alarm Settings………………………………………………………………………………………………………………20

5.7 Miscellaneous Settings…………………………………………………………………………………………………23

5.8 Connection of RS-232 Cable for Programming………………………………………………………………28

6. Technical Specifications……………………………………………………………………………….……………29

CONTENTS

PACKAGE CONTENTS

WT-1011RC IP65 GSM Remote Controller

And Alarm S

stem

WT-1011RC IP65 – USER MANUAL – Rev.1.6 – Technical Support: [email protected]

WITURA CORPORATION SDN BHD

WITURA WT-1011RC GSM Remote Controller and Alarm System allow you to use your

mobile phone to monitor and control your business from any location. Its alarm facilities

provide a flexible way to distribute critical alarm information to any number of mobile

phone users.

WT-1011RC provides detailed alarm messages, secure alarm acceptance, full alarm

reporting and even remote process control. This allows user to rectify problems directly

via their mobile phone within minutes of the alarm occurring.

The WT-1011RC can monitor 2digital inputs. A SMS alarm message can be sent when

inputs triggered. The user can also interrogate the inputs through SMS messaging. The

WT-1011RC also has 2heavy-duty relay outputs can be used to switch on any

application like lamps, pumps, heaters etc. Output Relay 1 can be switched ON for a

preset time by calling its cell phone number, there is no call charges incurred when

dialing the unit as it will recognize an authorized telephone number calling it and reject

the call without answering. Output Relay 2 can be programmed to switch on for a pre-

determined length of time by sending the WT-1011RC a text command.

More flexible than pager based systems

Low set up and running costs

Faster response to alarms and process disturbances

Allows reduced manning levels

Increased freedom of movements for users

Reduces wasted traveling time responding to alarm events

Provides more detailed information

Easier monitoring of remote process

Allows full remote control

WT-1011RC is a versatile SMS alert device suited for most monitoring needs. It is

simple to use yet is packed with powerful functionalities to meet a wide ranging

industrial and commercial and residential applications

2. FEATURES

1. INTRODUCTION

3. CHARACTERISTIC

WT-1011RC IP65 GSM Remote Controller

And Alarm S

stem

WT-1011RC IP65 – USER MANUAL – Rev.1.6 – Technical Support: [email protected]

WITURA CORPORATION SDN BHD

Housed in the weather and desk proof IP65 enclosure complete with internal industrial

modem, monitoring controller and flexible operating firmware. It is very easy to setup,

install and use.

Most equipment today does provide some form of alerting signal to interface to

monitoring devices from reporting of various malfunction or abnormalities. There are

various kinds of signal that the equipment can send out, most common of which are

opening or closure of one or more switch relay contact. UPS usually provide signals such

as incoming power fail, battery mode, battery level low, and switchover failure. An air

conditioner system may provide signals such as system on/off, compressor over

temperature, low gas pressure, etc.

Equipments to be monitored are connected to WT-1011RC using these alarm signaling

contacts. WT-1011RC keeps a constant watch over all the contacts. Whenever any

contact input changes status (either from a close to open or from an open state to close

state) it is captured by WT-1011RC. It will then process the input according to the

configuration provided by the user. The correct SMS messages will be sent to 8 mobile

phone users.

WT-1011RC is so fast in capturing the change of status of any signaling contacts that no

event will be missed out up to 2 inputs can be monitored directly. The flexibility of WT-

1011RC is in allowing remote query of input status using SMS.

To change contacting mobile phone number is also very easy. Authorize personal

remotely using SMS command to add, change or delete mobile phone number in WT-

1011RC.

WT-1011RC is a 2 way device. Besides monitoring inputs and act upon such inputs it

also allow mobile phone users to compose SMS messages to it. When WT-1011RC

receives any SMS, it will look its memory bank to see what it is supposed to do and

action according. No action SMS are ignored.

3.1 Standalone Operation

3.2 2 Digital Inputs

3.3 2 Digital Outputs

WT-1011RC IP65 GSM Remote Controller

And Alarm S

stem

WT-1011RC IP65 – USER MANUAL – Rev.1.6 – Technical Support: [email protected]

WITURA CORPORATION SDN BHD

Relay 1 can turned on for a preset time by calling its number and Relay 2 can be

activated by text messages from mobile phone. Creating action messages are done with

the same ease as that of input monitoring.

Authorized groups can also query the status of an input or output. This is very useful

feature to determine the present status of an input or output. The enquirer need not

wait for an alarm to happen in order to receive the given I/O status.

Authorized users can send a SMS command to trigger on or off the digital output. Upon

receiving the command, WT-1011RC will perform the instructed action. After the on or

off action is done, it will send a reply to the querying mobile phone as an

acknowledgement.

WT-1011RC has a feature to allow user to remotely add, change or delete any mobile

phone numbers in WT-1011RC memory.

Re-assigning of operation personnel, a change of mobiles phone number is also

common. Rather than having to physically go to the installation site with a notebook

computer, the authorized personnel can perform the change from anywhere using

mobile phone. Where there are many installed sites, this feature saves time and afford.

Authorized mobile phone group can perform system check by sending a command to

WT-1011RC. If WT-1011RC is switched on or working normally, it will reply to the

querying number.

Integral to the design of WT-1011RC is a GSM 850/900/1800/1900Mhz Industrial

grade modem. Its capabilities and performance are highly optimized by the operating

firmware. Any change in the GSM signal and receiving conditions are detected quickly

and the software automatically takes care of signal errors

3.4 Querying Inputs And Outputs Status

3.5 Turning On / Off Device Remotely

3.6 Remote Editing Of Mobile Phone Numbers

3.7 System Check

3.8 GSM Modem

WT-1011RC IP65 GSM Remote Controller

And Alarm S

stem

WT-1011RC IP65 – USER MANUAL – Rev.1.6 – Technical Support: [email protected]

WITURA CORPORATION SDN BHD

Besides running the necessary program to perform all the required functions, WT-

1011RC has diagnostic routines running alongside. Being a monitoring device, WT-

1011RC must have a very high operating reliability and stability. Every section of WT-

1011RC is monitoring each other. Should the modem fail to perform its required role,

the controller will interrogate and restart the modem.

For monitoring and remote control of equipments and machines that are able to provide

dry contract signals. 2 digital outputs with pulse functions extend control functions.

Suitable for door access control, On/Off equipment remotely, resetting of Routers,

Network switches etc. Some application examples are: -

Machines, Standby Power Generator, Electrical Panels, Pumps, Uninterruptable Power

Supplies, DC rectifier systems, Vending Machines, Fire Alarm Panels, Gas Monitoring

Systems, ATM Machines, Security Systems, Fishery, Cold rooms, HVAC systems, Door

Security, Network equipment and more.

IMPORTANT!

Please read through the instruction manual before you start to install and program the

device.

If you are unsure how to connect the device you wish to control please refer to a qualified

person.

Requirements:

- The WT-1011RC requires a 15 volt DC power supply capable of providing a minimum current of

1500mA, typical current consumption is 60mA

- A mobile phone SIM card with sufficient credit to send confirmation text messages when

programming the WT-1011RC unit. Note: The WT-1011RC identifies only 3V SIM card

3.9 Reliable Performance

3.10 Application

4. INSTALLATION INSTRUCTION

WT-1011RC IP65 GSM Remote Controller

And Alarm S

stem

WT-1011RC IP65 – USER MANUAL – Rev.1.6 – Technical Support: [email protected]

WITURA CORPORATION SDN BHD

Installation:

Installing the SIM Card

Note: Installing the SIM Card. Please be sure the initial 4 digit PIN code of SIM card is disabled.

This can be done by placing it in an unlocked Mobile phone and first checking if the SIM requested

any PIN code. If this is the case the PIN code can be disabled using the security settings on the

phone.

Proceed as follows

1. Slide back the SIM door and lift it up

2. Slide the SIM card into the SIM door making sure that the clipped corner of the SIM card lines

up with the clipped corner of the SIM holder

3. Close the SIM door

4. Slide the SIM door to lock the SIM card in place

Power Up the Device

Connect a 15 volt DC power supply to terminal 3 & 4 ensuring positive is connected to terminal

3, switch on the power supply, the power LED will lit indicating power is present, the network

LED indicator will initially flash quickly, once logged onto the network it will flash more slowly

approximately every 3 to 4 seconds

Note: You should install the WT-1011RC in a place where there is GSM signal coming from the

operator you want to use. Check it with a phone before proceeding with the installation. If you

need to install the device in a place with little signal, you may consider using an external antenna

that we may supply as an option to be purchased separately with 5m cable.

Input 15VDC Power

here

Power Switch

Insert SIM card

here

Install Antenna

here

Connect to Battery

Back-u

WT-1011RC IP65 GSM Remote Controller

And Alarm S

stem

WT-1011RC IP65 – USER MANUAL – Rev.1.6 – Technical Support: [email protected]

WITURA CORPORATION SDN BHD

Connection Details:

If you are unsure how to connect the device you wish to control please refer to a qualified

person.

Port Descriptions

1 +12 volts DC Output Audible Alarm Output

2 - 12 volts DC Output

3 +15 volts DC Input a 15 volts DC power that capable of

providing a current of 1.5 Amp

4 - 15 volts DC

5 +5 volts DC output Auxiliary 5 volts DC Output can be used to

trigger the inputs

6 Input 2 (IN2) A Standard +5V TTL signal will trigger this

Input

7 Ground (COM)

8 Input 1 (IN1) A Standard +5V TTL signal will trigger this

Input

9 Ground (COM)

10 NORMALLY OPEN (N.O) OUTPUT RELAY 2

(Can be Switched ON/OFF by SMS)

11 COMMON (COM)

12 NORMALLY CLOSED (N.C)

13 NORMALLY OPEN (N.O) OUTPUT RELAY 1

(Can be Switched ON by Caller ID)

14 COMMON (COM)

15 NORMALLY CLOSED (N.C)

1 2 3 4 6 7 8 9

NCNO C

15VDC

Power

Input

OUTPUT RELAY 2

10 11

12VDC

Audible

Alarm

Output

INPUT 2 INPUT 1

+-IN2

12 13 14 15

IN1

COM

NO C NC

OUTPUT RELAY 1

+5VDC

Output

WT-1011RC IP65 GSM Remote Controller

And Alarm S

stem

WT-1011RC IP65 – USER MANUAL – Rev.1.6 – Technical Support: [email protected]

WITURA CORPORATION SDN BHD

Example of Input & Output Connections

You can program the WT-1011RC via SMS commands using your phone. Any

programming command sent by SMS must be in CAPITAL letters. The fields between

square brackets are parameters; do NOT enter the square brackets. When you send a

command, you will receive the answer for the first time even if your GSM number is not

in the administrator list. This happens because the WT-1011RC recognizes any GSM

number as administrator and answers to it.

Attention: Please program the WT-1011RC unit systematically begin with programming the

administrator number.

The 8 administrator numbers can be programmed with a text command via SMS.

Text Command:

*TEL[N]#XXXXXXXXXX

N stands for administrator number 1 - 8

XXXXXXXXXX stands for the phone number you want to program as administrator.

1 2 3 4 6

NCNO C

15VDC

Power

Input

OUTPUT RELAY 2

INPUT 2 INPUT 1

+-IN2

13 14 15

IN1

COM

NO C NC

OUTPUT RELAY 1

LIGHT

110VAC

HEATER

110VAC

+5VDC

12VDC

Audible

Alarm

Output

+5VDC

Output

5. WT-1011RC PROGRAMMING INSTRUCTIONS (via SMS Only)

5.1 Programming the Administrator Number

WT-1011RC IP65 GSM Remote Controller

And Alarm S

stem

WT-1011RC IP65 – USER MANUAL – Rev.1.6 – Technical Support: [email protected]

WITURA CORPORATION SDN BHD

Please note that it is possible to program up to a maximum of 16 digits for a phone

number.

Example:

To program phone number 1111222233 as administrator into list number 1, you would

send the following SMS command to the unit.

*TEL1#1111222233

After sending the above command, the WT-1011RC will reply a message back to you

that the administrator number has been added.

Example of Returned Message:

#TEL1=1111222233

Note: It is advised that the owner should set the system to allow programming

access and remote control of Output Relay 1 for administrators only after

programming the Administrator numbers.

Sending SMS Command: *ANY?#1

Only the administrators in the list will have the authority to access the system and

remote control of Output Relay 1 by calling its number, any person outside the list in

this case will not have the authority to access the system and text command sent to the

system will be rejected.

To allow any person gain access to the system just send SMS Command: *ANY?#0

Note: Only Administrator number 1 and 2 may send this SMS command

The system allows the phone numbers in the Guest List as authorized user to operate

the output relays when calling its number. When the system received a phone call from

the Guest List, it will activate the output relays without answering the call therefore it is

free of charge. If it is not a registered user of the Guest List the call is rejected and the

output relays will never trigger. It is possible to program up to 100 phone numbers to be

authorized users in the Guest List of the unit and this can be done by sending the

following SMS to the unit.

5.2 Access Control For Administrators

5.3 Programming the Guest List

Indice

Altri manuali Witura Sistema di sicurezza

Witura

Witura WT-1010C2 Manuale utente

Witura

Witura WT9002 Manuale utente

Witura

Witura WT-1010SA Manuale utente

Witura

Witura WT-1672A Istruzioni operative

Witura

Witura WT-1010C2 Manuale utente

Witura

Witura WT-9001 IP65 Manuale utente

Witura

Witura WT9002 Manuale utente

Witura

Witura WT-1672B Manuale utente

Witura

Witura WT-1010SA Manuale utente

Witura

Witura WT-1010SA Manuale utente

Witura

Witura WT-9001 IP65 Manuale utente

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente