Wolf WWD30 Manuale utente

Warming Drawer

INSTALLATI N GUIDE

Important Note

To ensure the safe and efficient use of Wolf equipment,

please take note of the following types of highlighted

information throughout this guide:

IMP RTANT N TE highlights information that is

especially important.

CAUTI N signals a situation where minor injury or

product damage may occur if instructions are not

followed.

WARNING states a hazard that may cause serious injury

or death if precautions are not followed.

Contents

WolfWarmingDrawer ..........................3

Installation Considerations . . . . . . . . . . . . . . . . . . . . . . 4

Warming Drawer Installation . . . . . . . . . . . . . . . . . . . . 7

ServiceInformation...........................15

Features and specifications in this guide and on the website

are subject to change at any time without notice. Check our

website, wolfappliance.com, for the most up-to-date

specifications.

Wolf Warming Drawer 3

wolfappliance.com

Warming Drawer Installation

IMP RTANT N TE: This installation must be completed

by a qualified installer or Wolf authorized service center

technician.

Read this entire installation guide prior to installation and

save for the local inspector’s reference. The homeowner

should keep this installation guide for future reference.

Any questions or problems regarding installation of the

warming drawer should be directed to your Wolf dealer or

Wolf Appliance, Inc. at 800-332-9513, or visit our website

at wolfappliance.com.

IMP RTANT N TE: This appliance must be installed in

accordance with National Electrical Codes, as well as all

state, municipal and local codes. The correct voltage,

frequency and amperage must be supplied to the appli-

ance from a dedicated, grounded circuit which is

protected by a properly sized circuit breaker or time delay

fuse. The proper voltage, frequency, and amperage ratings

are listed on the product rating plate.

Record the model and serial number before installing the

warming drawer. Both numbers are listed on the product

rating plate, located on the left front floor area of the inner

cabinet. To access the rating plate, the drawer must be

fully open. Refer to the illustration below.

Location of rating plate.

RATING

P ATE

Wolf Warming Drawer

Model Number WWD30

Serial Number

Installation Considerations 4

Before You Start

•Proper installation is the responsibility of the installer.

Product failure due to improper installation is not

covered under the Wolf warranty. Refer to the warming

drawer use & care guide for warranty details.

•Warranty service must be performed by a Wolf author-

ized service center. Wolf is not responsible for service

required to correct a faulty installation.

•Model WWD30 must be installed with a Wolf stainless

steel or integrated drawer front. Make sure you have

the accessory drawer front called for in your installa-

tion. Specific installation instructions are included with

the drawer front.

•Make sure cabinetry meets the minimum dimension

requirements for your specific installation.

•Check with local utilities for electrical codes that apply

in your area. ocal codes vary. Installation, electrical

connections and grounding must comply with applica-

ble codes. In the absence of local codes, the drawer

should be installed in accordance with National Electri-

cal Code ANSI/NFPA 70-1990 or latest edition.

•This appliance must be properly grounded. Refer to

electrical requirements on page 13.

•Make sure you have the tools and materials necessary

for proper installation.

T LS AND MATERIALS REQUIRED

•Minimum 3/4" (19) thick lumber for the solid platform

that supports the warming drawer—must be able to

support 200 lbs (91 kg)

•Wood screws and hardware to install the platform

•2" x 2" or 2" x 4" lumber for anti-tip block

•Power saw

•evel

•Drill and 1/16" bit, 1/2" bit also for integrated drawer

front application

•Phillips screwdriver

•2 wood screws (provided)

•Wood cleats (optional)

Installation Considerations 5

wolfappliance.com

Installation Considerations

M DEL WWD30

•Model WWD30 must be installed with a Wolf stainless

steel or integrated drawer front. Specific installation

instructions are included with the drawer front.

•The warming drawer platform must be able to support

200 lbs (91 kg).

•The warming drawer platform must be a minimum of

1" (25) above the toe kick to allow for the overlap of the

warming drawer trim.

•For undercounter installations, 231/2" (597) from the

bottom of the warming drawer opening to the floor is

typical.

C MBINATI N INSTALLATI NS

•Model WWD30 may be installed in combination with a

Wolf built-in oven and/or microwave. Additional clear-

ance between warming drawer and oven openings may

be required. To allow the warming drawer trim and the

oven trim to meet, a 7/8" (22) platform may be used to

separate the two openings. This will act as the support

platform for the oven and the anti-tip device for the

warming drawer. An anti-tip block may be installed at

the rear of the cabinet in place of the platform. If the

warming drawer is installed above an oven, a 7/8" (22)

platform is required to allow for clearance of overlaps.

•Model WWD30 may be installed below a Wolf cooktop

or sealed burner rangetop. Allow enough room for gas

and electrical connections for the cooktop.

•Model WWD30 may be installed next to or above

another Wolf warming drawer.

IMP RTANT N TE: For combination installations, refer to

installation instructions provided with the other Wolf

products for additional specifications.

Installation Considerations 6

223/4"(578)

281/4"(718)

(229)

103/8"

(264)

211/2"

(546)

3/4"

(19)

3/4"(19)

297/8"(759)

OR 357/8"(911)

Drawer Front Panel and Handle Dimensions

L SERIES PANEL ABC

Tubular Handle 7/8"(22) 31/2"(89) 25" (635)

1-INCH THICK PANEL ABC

Tubular Handle 11/8"(29) 31/2"(89) 25" (635)

Curved Handle (framed) 11/8"(29) 23/4"(70) 241/4"(616)

Curved Handle (unframed) 11/8"(29) 23/4"(70) 241/4"(616)

Pro Handle 11/8"(29) 31/2"(89) 25" (635)

2-INCH THICK PANEL ABC

Pro Handle (30-inch wide) 21/8"(54) 41/2"(114) 26" (660)

Pro Handle (36-inch wide) 21/8"(54) 41/2"(114) 26" (660)

INTEGRATED PANEL ABC

Custom Handle 1/4"(6) NA NA

WWD30 Drawer Front Options

IMP RTANT N TE: Model WWD30 must be installed with

a Wolf stainless steel or integrated drawer front.

When installing a Wolf warming drawer in combination

with an Series built-in oven, Wolf recommends using the

Series drawer front with tubular handle. For all other

warming drawer installations, a 1-inch or 2-inch thick

drawer front with handle is recommended. These front

panels are designed on the E Series front panel platform

and are available with a tubular, curved or pro handle.

The 2-inch thick drawer fronts with pro handle are

designed to be installed below a sealed burner rangetop

so the panel aligns properly with the front of the rangetop.

VERALL DIMENSI NS

Dimensions may vary ± 1/8" (3).

IMP RTANT N TE: Throughout this guide, dimensions in

parentheses are in millimeters unless otherwise specified.

Warming Drawer Installation 7

wolfappliance.com

WWD30 with Series Drawer Front

UNDERC UNTER INSTALLATI N

2"(51) x 2"(51)

ANTI-TIP BLOCK

DIMENSION

WILL VARY*

231/2"(597)

BOTTOM

OF OPENING

TO FLOOR

(typical)

*Dimension must accommodate height of anti-tip block and drawer face overlap. Dashed line represents profile of unit.

IMPORTANT NOTE: Unless you are using cabinets deeper than 24" (610), it is recommended that the electrical supply for the warming drawer

be placed in an adjacent cabinet within reach of the conduit.

FRONT VIEWSIDE VIEW

24" min (610)

CABINET DEPTH

33" rec (838)

30" min (610)

CABINET WIDTH

285/8"(727)

OPENING WIDTH

7/8"(22) PLATFORM

36" (914)

STANDARD

FLOOR TO

COUNTERTOP

HEIGHT

103/8"

(264)

91/8"(232)

OPENING HEIGHT

24" min (610)

CABINET DEPTH

271/2"

(699)

TRIM

HEIGHT

197/8"(505)*

TRIM

HEIGHT

273/16"

(691)

OPENING

HEIGHT

1811/16"(475)*

OPENING

HEIGHT

281/2"(724)

L SERIES OVEN

OPENING WIDTH

33" rec (838)

30" min (762)

CABINET WIDTH

17/16"(37) PLATFORM*

7/8"(22) PLATFORM

271/2"(699)

MICROWAVE

OPENING WIDTH

285/8"(727)

WARMING DRAWER

OPENING WIDTH

*Dimensions are for convection microwave. For standard microwave, opening height is 181/4" (464), trim height is 17" (432) and platform is 1" (25).

Dashed lines represent profile of unit. IMPORTANT NOTE: Unless you are using cabinets deeper than 24" (610), it is recommended that the

electrical supply for the warming drawer and for the oven be placed in an adjacent cabinet within reach of the conduit. Refer to L Series oven

specifications for electrical location.

FRONT VIEWSIDE VIEW

91/8"(232)

OPENING HEIGHT

103/8"

(264)

INSTALLATI N WITH 30" (762) L SERIES VEN AND MICR WAVE

Warming Drawer Installation 8

24" min (610)

CABINET DEPTH

243/8"

(619)

TRIM

HEIGHT

197/8"(505)*

TRIM

HEIGHT

241/16"

(611)

OPENING

HEIGHT

1811/16"(475)*

OPENING

HEIGHT

341/2"(876)

L SERIES OVEN

OPENING WIDTH

39" rec (991)

36" min (914)

CABINET WIDTH

17/16"(37) PLATFORM*

7/8"(22) PLATFORM

333/8"(854)

MICROWAVE

OPENING WIDTH

285/8"(727)

WARMING DRAWER

OPENING WIDTH

*Dimensions are for convection microwave. For standard microwave, opening height is 181/4" (464), trim height is 17" (432) and platform is 1" (25).

Dashed lines represent profile of unit. IMPORTANT NOTE: Unless you are using cabinets deeper than 24" (610), it is recommended that the

electrical supply for the warming drawer and for the oven be placed in an adjacent cabinet within reach of the conduit. Refer to L Series oven

specifications for electrical location.

FRONT VIEWSIDE VIEW

91/8"(232)

OPENING HEIGHT

103/8"

(264)

WWD30 with Integrated Drawer Front

INSTALLATI N WITH 36" (914) L SERIES VEN AND MICR WAVE

Warming Drawer Installation 9

wolfappliance.com

WWD30 with 1-Inch Thick Drawer Front

UNDERC UNTER STANDARD INSTALLATI N

2"(51) x 2" (51)

ANTI-TIP BLOCK

DIMENSION

WILL VARY*

231/2"(597)

BOTTOM

OF OPENING

TO FLOOR

(typical)

*Dimension must accommodate height of anti-tip block and drawer face overlap. Dashed line represents profile of unit.

IMPORTANT NOTE: Unless you are using cabinets deeper than 24" (610), it is recommended that the electrical supply for the warming drawer

be placed in an adjacent cabinet within reach of the conduit.

FRONT VIEWSIDE VIEW

24" min (610)

CABINET DEPTH

36" rec (914)

33" min (838)

CABINET WIDTH

303/8"(772)

FLUSH INSET WIDTH

285/8"(727)

OPENING WIDTH

7/8"(22) PLATFORM

7/8"(22) TOP AND SIDE CLEATS

TOP VIEW

SIDE CLEATS

24"min (610)

FLUSH INSET

DEPTH

1" (32)

36" (914)

STANDARD

FLOOR TO

COUNTERTOP

HEIGHT

107/8"(276)

FLUSH INSET

HEIGHT

91/8"(232)

OPENING HEIGHT E

2"(51) x 2" (51)

ANTI-TIP BLOCK

DIMENSION

WILL VARY*

231/2"(597)

BOTTOM

OF OPENING

TO FLOOR

(typical)

*Dimension must accommodate height of anti-tip block and drawer face overlap. Dashed line represents profile of unit.

IMPORTANT NOTE: Unless you are using cabinets deeper than 24" (610), it is recommended that the electrical supply for the warming drawer

be placed in an adjacent cabinet within reach of the conduit.

FRONT VIEWSIDE VIEW

24" min (610)

CABINET DEPTH

33" rec (838)

30" min (610)

CABINET WIDTH

285/8"(727)

OPENING WIDTH

7/8"(22) PLATFORM

36" (914)

STANDARD

FLOOR TO

COUNTERTOP

HEIGHT

91/8"(232)

OPENING HEIGHT 103/8"

(264)

UNDERC UNTER FLUSH INSET INSTALLATI N

Warming Drawer Installation 10

24" min (610)

CABINET DEPTH

277/8"

(708)

TRIM

HEIGHT

103/8"(264)

197/8"(505)*

TRIM

HEIGHT

273/16"

(691)

OPENING

HEIGHT

1811/16"(475)*

OPENING

HEIGHT

281/2"(724)

E SERIES OVEN

OPENING WIDTH

33" rec (838)

30" min (762)

CABINET WIDTH

17/16"(37) PLATFORM*

7/8"(22) PLATFORM

271/2"(699)

MICROWAVE

OPENING WIDTH

285/8"(727)

WARMING DRAWER

OPENING WIDTH

*Dimensions are for convection microwave. For standard microwave, opening height is 181/4" (464), trim height is 17" (432) and platform is 1" (25).

Dashed lines represent profile of unit. IMPORTANT NOTE: Unless you are using cabinets deeper than 24" (610), it is recommended that the

electrical supply for the warming drawer and for the oven be placed in an adjacent cabinet within reach of the conduit. Refer to E Series oven

specifications for electrical location.

FRONT VIEWSIDE VIEW

91/8"(232)

OPENING HEIGHT

WWD30 with 1-Inch Thick Drawer Front

STANDARD INSTALLATI N WITH E SERIES VEN AND MICR WAVE

Altri manuali per WWD30

Indice

Altri manuali Wolf Cassetto scaldavivande

Manuali Cassetto scaldavivande popolari di altre marche

Siemens

Siemens HW 290 Series Manuale utente

Hatco

Hatco HDW-1 Istruzioni per l'installazione

APW Wyott

APW Wyott WD-2CMF Manuale utente

Viking

Viking DEWD102SS Manuale utente

Miele

Miele ESW 6229 Manuale utente

Brandt

Brandt WD1014X Manuale utente

KitchenAid

KitchenAid KOWT107ESS Manuale utente

Gaggenau

Gaggenau WSP 222 Manuale utente

DCS

DCS WDI Manuale utente

Fisher & Paykel

Fisher & Paykel OR90SCG6R1 Manuale utente

Electrolux

Electrolux EED21600X Manuale utente

Fisher

Fisher PROFESSIONAL WB76SPEX1 Manuale utente

Electrolux

Electrolux EW30WD55GS Manuale utente

Hanseatic

Hanseatic TCN14J6D-S Manuale utente

Jenn-Air

Jenn-Air JWD6030CDX Manuale utente

Gaggenau

Gaggenau WS482710 Manuale utente

Bosch

Bosch HWD2720UC Manuale utente

NEFF

NEFF N29HA11Y2 Istruzioni operative e di manutenzione