Wonderfire Eclipse 654 Manuale utente

3002616/05

OWNER’S GUIDE

THIS APPLIANCE IS FOR USE WITH NATURAL GAS (G20)

WHEN CONVERTED USING CONVERSION KIT NO. 0595201 THIS

APPLIANCE IS FOR USE WITH PROPANE GAS (G31)

THIS APPLIANCE IS FOR USE IN THE UNITED KINGDOM (GB) AND THE

REPUBLIC OF IRELAND (IE) ONLY.

This guide is intended to help you care for your Wonderfire gas fire. Please read

thoroughly before using and keep for future reference

We trust that this guide gives sufficient details to enable your appliance to be operated

and maintained satisfactorily. However, if further information is required, our

Wonderfire Technical Helpline will be pleased to help.

Please telephone 08706 061 065 (National call rates apply in the United Kingdom).

This guide to be left with the owner

Eclipse

INSET LIVE FUEL EFFECT GAS FIRE

Model 654

(GC No. 32-032-48)

OWNER’S GUIDE

Page 2

Safety First.

Wonderfire fires are CE Approved and designed to meet the appropriate British

Standards and Safety Marks.

Quality and Excellence.

At the heart of every Wonderfire fire.

All Wondefire fires are manufactured to the highest standards of quality and excellence

and are manufactured under a BS EN ISO 9001 quality system accepted by the British

Standards Institute.

The Highest Standards

Wonderfire is a member of the Society of British Gas Industries which works to ensure

high standards of safety, quality and performance.

Careful Installation

Wonderfire is a CORGI registered company. All our gas fires must be

installed by a competent CORGI Registered Installer in accordance

with our Installer Guide and should not be fitted directly on to a

carpet or floor of combustible material.

Wonderfire, Erdington, Birmingham B24 9QP

www.firesandstoves.co.uk

Because our policy is one of constant development and improvement, details may vary slightly from those

given in this publication

OWNER’S GUIDE

Page 3

LIST OF CONTENTS

SAFETY ........................................................................................................................... 4

APPLIANCE DIMENSIONS......................................................................................... 6

GAS CONSUMPTION ................................................................................................... 6

OPERATING YOUR FIRE ........................................................................................... 7

The Oxysafe flame sensing & flue blockage safety system. ........................................ 7

To light the fire.............................................................................................................. 7

Lighting with a taper ..................................................................................................... 9

To turn off .....................................................................................................................9

CLEANING.................................................................................................................... 10

Metal Parts................................................................................................................... 10

Ceramic burner ............................................................................................................ 11

FUEL BED REFITTING.............................................................................................. 11

MAINTENANCE .......................................................................................................... 14

Regular maintenance ................................................................................................... 14

Servicing...................................................................................................................... 14

This gas fire is designed to meet the most stringent quality, performance and safety

requirements to provide you with many years’ trouble-free service.

This guide aims to improve your understanding and appreciation of your gas fire by

providing simple and informative instructions to ensure that you benefit from the

excellent performance and features it has to offer.

OWNER’S GUIDE

Page 4

SAFETY

IF YOU SMELL GAS

DON’T SMOKE

EXTINGUISH ALL NAKED FLAMES

DON’T TURN ELECTRICAL SWITCHES ON OR OFF

TURN OFF THE GAS SUPPLY AT THE METER

OPEN DOORS AND WINDOWS TO GET RID OF THE GAS

IMMEDIATELY CALL THE GAS EMERGENCY SERVICE - SEE YOUR

LOCAL TELEPHONE DIRECTORY

Do have the fire installed by a competent person. In the United Kingdom, installation

must be in accordance with the latest edition of the Gas Safety (installation & use)

Regulations. In the Republic of Ireland, installation must be in accordance with all

national and local regulations in force.

Do have the chimney swept prior to installation if it was previously used for solid fuel.

Do have the fire installed in accordance with the installation instructions.

Do provide a minimum clearance as shown below above the hearth to any shelf made

of wood or other combustible material. Please bear this in mind if you are making any

alterations to the room.

Do provide a suitable guard that complies with BS 6539 or 6778 for the protection of

young children, the elderly and the infirm. Such a guard is also recommended for the

protection of pet animals. (Although this fire conforms to all the applicable standards, it

is a heating appliance and certain parts of its surface will become hot).

Do wait three minutes before attempting to relight if the fire is switched off or the

flames are extinguished for any reason. (Your fire is fitted with a safety device that will

automatically shut off the gas supply to the fire if, for any reason, the flames go out).

Do get advice about the suitability of any wall covering near your fire. Soft wall

coverings (e.g. embossed vinyl, etc.) which have a raised pattern are easily affected by

heat. They may, therefore, scorch or become discoloured when close to a heating

appliance. Please bear this in mind whenever you are considering redecorating.

Do provide a minimum side clearance as detailed in figure 1. Please bear this in mind if

ever you are considering altering the room.

OWNER’S GUIDE

Page 5

Graph 1. Combustible shelf clearances.

Do provide a minimum clearance as shown below above the hearth to any shelf made of

wood or other combustible material. Please bear this in mind if you are making any

alterations to the room

•For a shelf up to 150mm deep

Minimum height = 700mm.

•For a shelf deeper than 150mm

Minimum height = 700mm + 12.5mm for every 25mm depth over 150mm.

See graph 1.

Don’t hang clothing, towels or any other fabrics over the fire.

Don’t add any extra pebbles above the number stated in this guide. This could cause a

safety hazard.

Don’t put paper or any other material on the fire.

Don’t place any combustible material (rugs, carpet, plastic tiles, etc.) on the hearth.

Don’t attempt to clean or service the fire until it has been switched off and allowed to

cool completely.

OWNER’S GUIDE

Page 6

APPLIANCE DIMENSIONS

GAS CONSUMPTION

Model 654

Has a maximum natural gas input of 5.1kW (Gross)

Has a maximum natural gas output of 2.6kW (Gross)

Has a minimum natural gas input of 2.2kW (Gross)

Has a minimum natural gas output of 1.03kW (Gross)

Model 654 when converted using kit number 0595201

Has a maximum propane gas input of 5.1kW (Gross)

Has a maximum propane gas output of 3.0kW (Gross)

Has a minimum propane gas input of 3.5kW (Gross)

Has a minimum propane gas output of 2.1 kW (Gross)

Figure 1. Appliance dimensions

OWNER’S GUIDE

Page 7

OPERATING YOUR FIRE

PLEASE NOTE

When operating your fire for the first time, some vapours may be given off which may

cause a slight odour and could possibly set off any smoke alarms in the immediate

vicinity. These vapours are quite normal with new appliances. They are totally harmless

and will disappear after a few hours use.

The Oxysafe flame sensing & flue blockage safety system.

For your safety, this appliance is fitted with a flue blockage safety device which will

shut down the appliance in the event of abnormal flue conditions. This device is NOT a

substitute for an independently mounted Carbon Monoxide detector.

The device will also automatically shut off the gas supply to the fire if the pilot flame

goes out due to lack of oxygen or for any other reason.

If this device starts to repeatedly shut off the gas, get expert advice.

This device incorporates a probe which senses that the heat from the pilot flame is

correct. If this probe is cool, the device will prevent any gas flow unless the control

knob is held in at the ignition position.

If, for any reason, the flames go out when the fire is hot or if the fire is turned off when

hot, always wait at least three minutes before attempting to relight.

To light the fire

To get access to the control knob lower the

bottom front cover. To do this, support the

top edges of the lower front cover and pull

gently (See figure 2).

KDepress the control knob and turn

anticlockwise towards the PILOT/IGN

position (See figure 3). A spark should be

generated at the pilot while turning. The

spark should ignite the pilot. The pilot

flame can be seen at the left side of the

pebbles.

KKeep the button at the PILOT/IGN

position for a further ten seconds. This will

prevent the flame sensing device from

shutting off the gas while its probe warms

up as explained previously.

Figure 2. Lower front cover.

OWNER’S GUIDE

Page 8

KIf the pilot does not ignite quickly

repeat the procedure.

KIf after 10 seconds pilot ignition

has not occurred, turn the control

knob back to the “Off” position, wait

for 3 minutes and then repeat the

ignition procedure.

KWhen the pilot is alight and stable,

partially depress the knob and turn to

“LOW”. The pilot should then light the

main burner at its low setting. There

may be a delay of up to four seconds

between the pilot lighting and ignition

of the gas at the main burner. This is

normal and is due to the time required

to fill the main burner compartment with sufficient gas for ignition.

KWhen the main burner is alight at its low setting, partially depress the knob and

gradually turn it anti-clockwise until the burner is at your desired level. The burner

flames will gradually increase until the knob reaches the “HIGH” position.

Note: i) If the flames go out while setting the control, repeat the full lighting

procedure. If the flames repeatedly go out have the fire serviced.

ii) Please note. When first turned on the flames will appear predominantly blue.

The pebbles will take time to warm up. Although some glow will be seen after

approximately ten minutes, the full visual effect will only be apparent after a

somewhat longer time.

iii) The appliance will operate to its maximum potential if the flue is primed

during the first 20 – 30 minutes of operation. To do this, simply set the control

knob to its ‘HIGH’ setting. This will also burn off any carbon deposits that

may have formed during previous operations.

iv) If operating the appliance for long periods it is beneficial occasionally to

change the settings. This will also help to remove any carbon deposits that

may form during operation

Figure 3. Control knob

OWNER’S GUIDE

Page 9

Figure 4 Lighting with a taper

Lighting with a taper

See figure 4.

In the unlikely event of failure of the ignition spark, the pilot can be lit by a taper or

long spill. Insert the taper or spill into the gap underneath the pebble at the extreme left

hand side of the fuel bed. Depress the control knob, turn it to PILOT/IGN

To turn off

KTo turn the main burner off but leave the pilot

alight, partially depress the knob and turn to

PILOT/IGN.

KTo turn the fire fully off, partially depress the

knob and turn to OFF.

KWait at least three minutes before

relighting.

KWhile cooling, the coals may make some

crackling noises. This is quite normal.

OWNER’S GUIDE

Page 10

CLEANING

To maintain the high performance and quality finish of your fire please follow these

guidelines:

•Before attempting to clean the fire, please remember to turn off the fire and wait for

the appliance to cool completely. The fire will retain heat for some time before cleaning

can begin.

•If any pieces of debris are found in the hotbox, have the chimney inspected before

further use.

Metal Parts

•Clean the metal parts with a slightly damp, lint free non-abrasive cloth and then dry.

•Do not use abrasive cleaners as these will scratch the fire surface.

•Front surround -Clean the metal parts with a slightly damp cloth and then dry. If

this does not work apply a very small amount of ‘baby oil’ to a lint free, non-abrasive

cloth and wipe over the surface. Use a clean cloth to wipe off the oil.

•Note: The decorative metal surfaces within the firebox are exposed to high

temperatures. Great care has been taken to ensure that discolouration is kept to a

minimum. However, the combination of heat and variable flue conditions may result in

small amounts of discolouration or staining.

Pebbles and Pebble base

•This product uses fuel effect pieces and Gaskets containing Refractory Ceramic

Fibres (RCF), which are man-made vitreous silicate fibres. Excessive exposure to

this material may cause irritation to eyes, skin and respiratory tract.

Consequently, it is important to take care when handling these articles to ensure

that the release of dust is kept to a minimum.

•In the unlikely event of soot forming, light coatings will usually be burnt off during

the normal operation of the fire.

•Should any soot accumulation become excessive, the fuel effect pieces should be

removed from the fire for cleaning.

•Cleaning should be carried out in a well ventilated area or in the open air by gently

brushing with the pieces held away from your face so that you avoid inhaling the dust.

•We do not recommend the use of a normal domestic vacuum cleaner which may

blow dust back into the air.

•We suggest that you remove the pebbles in the reverse order to that shown in the fuel

bed refitting instructions.

Altri manuali per Eclipse 654

Indice

Altri manuali Wonderfire Camino da interno

Wonderfire

Wonderfire BR00290 SONNET Istruzioni per il montaggio

Wonderfire

Wonderfire 955 Istruzioni per l’uso

Wonderfire

Wonderfire Sonnet Plus Manuale utente

Wonderfire

Wonderfire BR419 Manuale utente

Wonderfire

Wonderfire sonnet br218 Manuale utente

Wonderfire

Wonderfire airflame excel mk.3 AC 16XL Manuale utente

Wonderfire

Wonderfire Marseille BR622 Manuale utente

Wonderfire

Wonderfire nexus BR648 VA Istruzioni per il montaggio

Wonderfire

Wonderfire AF 18XL Guida utente

Wonderfire

Wonderfire airflame excel mk.3 ac 18xl rc Manuale utente

Wonderfire

Wonderfire 762 Istruzioni per l’uso

Wonderfire

Wonderfire Lincoln BR517S Istruzioni per il montaggio

Wonderfire

Wonderfire airflame excel mk.3 ac 18xl Istruzioni per l’uso

Wonderfire

Wonderfire airflame excel mk.3 AC 16XL RC Manuale utente

Wonderfire

Wonderfire The Gallery BR218C1 Guida utente

Wonderfire

Wonderfire airflame excel mk.3 ac 18xl Manuale utente

Wonderfire

Wonderfire 762 Istruzioni per l’uso

Wonderfire

Wonderfire Marseille BR622 Istruzioni per il montaggio

Wonderfire

Wonderfire sonnet plus br645 VA Istruzioni per il montaggio

Wonderfire

Wonderfire 961 Manuale di istruzioni

Wonderfire

Wonderfire 037 Istruzioni per il montaggio

Wonderfire

Wonderfire Overture 2 BR265 Istruzioni per il montaggio

Wonderfire

Wonderfire 963 Istruzioni per l’uso

Wonderfire

Wonderfire Nexus Istruzioni per il montaggio

Manuali Camino da interno popolari di altre marche

Brigantia

Brigantia 35-DVRS31N-2 Manuale del proprietario

Nordpeis

Nordpeis Bergen Manuale utente

Superior

Superior BCT2536TMN Manuale utente

Quadra-Fire

Quadra-Fire 5100I-GD-B Manuale utente

Renaissance

Renaissance RUMFORD 1000 Manuale utente

Lacunza

Lacunza IV-800 Manuale utente

Baxi

Baxi 940 Istruzioni per l’uso

Dru

Dru Maestro 60/2 Tall RCH Manuale utente

Diamond Fireglass

Diamond Fireglass SS-O22 Manuale utente

HearthStone

HearthStone Windsor Bay 8830 Manuale di programmazione

Napoleon

Napoleon ASCENT B42 Manuale utente

Enviro

Enviro E33GI Manuale utente

Smeg

Smeg L30 FABE Istruzioni di montaggio

KEDDY

KEDDY K700 Manuale utente

Godin

Godin 3451 Manuale utente

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manuale utente

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manuale utente

Desa

Desa CCFPDFT Manuale operativo