Wonwoo MMK-H208 Istruzioni per l'installazione
IR PTZ Camera
INSTALLATION / OPERATING MANUAL
- Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
- The design and specifications are subject to be changed without prior notice to improve
product’s quality.
P/N : 388068605
TABLE OF CONTENTS
3p.
4p.
4p.
5p.
6p.
7p.
9p.
9p.
30p.
40p.
40p.
40p.
40p.
41p.
42p.
45p.
1. PRECAUTIONS
1. 1 Important Safety Instruction ...................................................................................
2. GETTING STARTED
2. 1 Unpacking ..............................................................................................................
2. 2 Part name ..............................................................................................................
2. 3 DIP Switch Setting .................................................................................................
2. 4 Cable Connection ...................................................................................................
3. INSTALLATION
3. 1 Installation .............................................................................................................
4. MAIN SETUP MENU
4. 1 Initialize .................................................................................................................
4. 2 Motion Setting .......................................................................................................
4. 3 Dome Setting ........................................................................................................
4. 4 Clear Setting .........................................................................................................
4. 5 Factory set ...........................................................................................................
4. 6 PTZ Reset .............................................................................................................
4. 7 Other Quick Opercating Guide ...............................................................................
5. SPECIFICATION
5. 1 Mechanism Specification .......................................................................................
6. DIMENSION
6. 1 DIMENSION ..........................................................................................................
7. CONFIGURATION
7. 1 Connecting to Keyboard with DVR .........................................................................
02
1. 1 Important Safety Instruction
•
Read these instructions.
•
Pay attention on all the warnings.
•
Follow all instructions.
•
Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
•
Do not dissemble or insert foreign objects.
•
Do not install near any heat sources such as radiation, beat registers, stoves, or other apparatus.
(Including amplifiers) that produce heat.
•
Do not aim the camera at the sun or any other strong light source.
•
Do not install the camera in intermittent lighting environments.
•
Only use attachments/accessories specified by the manufacturer.
•
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.
•
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
•
Installation should be done only by qualified personnel and conform to all local codes.
•
Installation should be done in a place strong enough to hold it.
•
Use only installation methods and materials capable of supporting four times the maximum specified load.
•
It is designed for indoor use only and it must not be installed where exposed to rain and moisture
without additional outdoor housing and bracket.
•
To prevent damage from water leakage when installing a mount outdoors on a roof or wall,
apply sealant around the bolt holes between the mount and mounting surface.
•
These instructions are for use by qualified service personnel only. To reduce the risk of electric shock
do not perform any servicing other that contained in the operating instructions unless you are qualified
to do so.
•
Only use replacement parts recommended by manufacturer.
ad these instructions.
1. PRECAUTIONS
03
2. 1 Unpacking
The following parts are supplied with the outdoor speed PTZ dome system.
2. GETTING STARTED
<Figure 1. package Components>
2. 2 Part name
<Wall type>
Wall bracket
Plate rubber
<Ceiling type>
TAPE SEALCeiling bracketWall bracket Mount+Socket+Cable
Mount joint Manual Power adaptor(Option)
SCREW (M4*8 SUS)
Screw Screw
SCREW (SET ANCHOR 1/4")
Body Mount Wiper(Spare)
FRONT BACK
ID Setting
Upgrade Port
Micro SD Card
IP Reset
Commnucation
Setting
SIDE
Safety Loop
*DIP S/W setting refers page 5.
1
2
3
4
5
6
04
2. 3 DIP Switch Setting
Before start up the dome camera, set the protocol and camera address and termination
set with dip-switches and click-switches as shown in the below diagram.
1.Set the camera address (ID)
2. Protocol, Baudrate, Camera setting
3.Set the termination On/Off
Address switch
Open the top cover of the product to set camera address.
* ID setting is 1~255 available S1
(x1)
S3
(x10)
S4
(x100)
S1 : 1-digit number of address
S3 : 10-digit number of address
S4 : 100-digit number of address
Ex) S4 = 1
S3 = 2
S1 = 8
The ID number is 128.
The device which is connected at the end of the line must have the
cable communication terminated. Without proper termination,
there is potential for control signal errors.
The product have the cable communication terminated by setting
the appropriate dip switch.
9
ON : Terminated
OFF : Not terminated
1 2 3 4 5 6 7 8 9 10
ON
SW2
DIP
SW3
1 2
ON DIP
1 2 3
OFF OFF OFF
OFF OFF ON
OFF ON OFF
OFF ON ON
ON OFF OFF
ON OFF ON
ON ON OFF
ON ON ON
PELCO-D
PELCO-P
WTX
EZP
NC
NC
NC
NC
PROTOCOL 4 5 6
OFF OFF OFF
OFF OFF ON
OFF ON OFF
OFF ON ON
ON OFF OFF
ON OFF ON
ON ON OFF
ON ON ON
2400
4800
9600
19200
38400
57600
115200
NC
BAUDRATE
9
OFF
ON
OFF
ON
RS LOOP
8
OFF
ON
NTSC
PAL
NTSC/PAL
1
OFF
ON
IP OFF
IP ON
IP SELECT 2
OFF
ON
OFF
PROGRAM MODE
BOOTO
7
OFF
ON
RS-422
RS-485
RSMODE 10
OFF
ON
NC
NC
NC
05
2. 4 Cable connection
2. 4. 2 RS-485/RS-422 Connection
2. 4. 1 Power/Data communication cable connection
RS-422/485 connection
The PTZ can be remotely controlled by an external device or control system, such as a control
keyboard or DVR, using RS-485 half-duplex, RS-422 duplex or simplex serial communication signals.
Connect marked TRx+, TRx- to Tx+ and Tx- of the RS-485 control system.
If control system is RS-422, connect Tx+,Tx- of controller to Rx+ and Rx- of the PTZ Camera series.
And also connect the Tx+, Tx- to Rx+, Rx- of the control device respectively. Total length
of the cable for communication should not exceed 1.2Km.
2. 4. 3 HD-SDI Output connection
Connect the HD-SDI out (BNC) connector to the monitor or video input of DVR. Video cable and
RS-485/422 communication cable are not provided in this product's package.
Do not connect the AC24V power terminal to
the communication terminal.
- Power Terminal: 2PIN
- Com Terminal: 4PIN
Caution
SPK:LGR
MIC:PK
RY1-COM:WT
RY1-NO:GRY
RY2-COM:VI
RY2-NO:BL
GND:GR
AL1:YL
AL2:OR
AL3:RD
AL4:BR
GND:BK
MAIN CABLE
HD-SDI CABLE
06
3. Installtion
- The following steps of installation and connection work should be done by qualified service personnel or system installers
and should conform to all local codes.
- Be sure to switch the camera off before installation is completed.
- Do not install the camera near the air outlet of an air conditioner.
- Before installation, set the dome system with Dip switch on the back side of the mechanism part, and assemble the mechanism
and housing according to the below instruction
3. 1 Installtion
Attach the provided wall bracket rubber to a wall bracket
as shown in the below picture.
After connecting the cable, set the mount
in the proper position and fix the 2 screws
(M4*8)
CEILING PIPE
Install calbes into the bracket first.
WALL BRACKET WALL BRACKET WALL BRACKET RUBBER
INSERT
MOUNT ADAPTOR
PIPE SOCKET CEILING PIPE
After connecting the cable, set the mount in the proper position
and fix the 2 screws (M4*8)
Install the bracket to the wall using anchor bolt.
When install the ceiling bracket, screw the ceiling pipe
to the pipe socket as figure.
Install the bracket to
the ceiling using
anchor bolt.
FRONT
FRONT
<Wall Mount Type>
<Ceiling Mount Type>
1 2
1
2 3
3 4
07
Fix the Fixture screw tightly.
1. Connect the safety loop on the body and mount back side.
2. Connect MAIN cable and HD-SDI cable onto the main body as figure.
(Caution! Fix the main body tightly.)
3. Align the arrow mark in the body and mount.
4. Fix the body by turn it to clockwise.
FIXTURE SCREW
OPEN
CLOSE
(Turn the body to clockwise)
SAFTY LOOP
08
4. MAIN SETUP MENU
4. 1 Initialize
4. 2 Motion Setting
The preset function is that the camera memorizes positions of the pan/tilt and zoom.
This function is a representative function of the speed dome which can find memorized
preset positions just by selecting the preset No. A Maximum of 255 Preset positions are toured in order.
4. 2. 1 Preset
(1) Select the Preset number
P001 : Defined Preset number / 001 : Undefined Preset number
Move : Select : NEAR
When the device is powered on, you can check the address,
version, protocol and video setting values.
INITIALIZE
: 001
: X. XX
: 1080p30/NTSC
: PELCO-D
: 2400.N.1
: XX XXX..OK
VER: XX, XX
OK
OK
PTZ ID
VERSION
D-OUTPUT
PROTOCOL
BAUDRATE
CAMERA
▷ PAN INIT . . . .
▷ TILT INIT . . . .
▷NORMAL SETTING WAIT . .
MAIN MENU
< NEAR / RIGHT ▷MOTION >
MOTION
▶
DOME
CAMERA
CLEAR
PTZ RESET
FACTORY SET
EXIT
MOTION MENU
< NEAR / RIGHT ▷PRESET >
PRESET ▶
TOUR
GROUP
SCAN
PATTERN
ALARM
AREA
PRIVACY
HOME POS
BACK EXIT
PRESET MENU
PRESET SELECT : 001
<EXIT FOCUS NEAR>
P001
006
011
016
021
026
031
036
041
P003
008
013
018
023
028
033
038
043
P002
007
012
017
022
027
032
037
042
P005
010
015
020
025
030
035
040
045
P004
009
014
019
024
029
034
039
044
PRESET MENU
< NEAR / RIGHT PRESETNUM >
NUMBER : 001
TITLE :
: AUTO
: OFF
FOCUS
EXIT TIME
POSITION SET ▶
SAVE CLR BACK EXIT
09
(3) Select the focus mode for Preset
(4) Define the Preset position
① Select the Position menu
or
NEAR
② Move and set the position ③ Set & Back
NEAR
(2) Set the Preset TITLE
Move : Select : or or Delete : or
TELE
JOYSTICK
WIDE
JOYSTICK
It’s available to set the desired TITLE, displayed on the executing screen of Preset.
After the TITLE is set, push the NEAR button to exit.
On focus menu, there are 3 modes
: AUTO, MANUAL, ONESHT.
* Focus will be adjusted once after preset moving.
① Select the Focus menu
or
NEAR
② Move and set the Focus Menu
PRESET POSITION
PRESET TITLE EDIT ( 01 )
< DELETE WIDE
< STORE TELE
BACK NEAR >
MOVE JOYSTICK >
TITLE :
0 1 2 3 4 5 6 7 8 9 (
) A B C D E F G H I J K
L M N O P Q R S T U V W
X Y Z . / , + - = < >
<EXIT FOCUS NEAR >
POSITION : 000. 0 000. 0
PRESET MENU
< NEAR / RIGHT ▷TITLE >
NUMBER : 001
TITLE :
: AUTO
: OFF
FOCUS
EXIT TIME
POSITION SET ▶
SAVE CLR BACK EXIT
PRESET MENU
< NEAR / RIGHT ▷PRESET POSITION >
NUMBER : 001
: OFF
TITLE
EXIT TIME
:
: AUTOFOCUS
POSITION SET ▶
SAVE CLR BACK EXIT
PRESET MENU
< NEAR / RIGHT ▷PRESET FOCUS >
NUMBER : 001
: OFF
TITLE
EXIT TIME
:
: AUTOFOCUS
POSITION SET ▶
SAVE CLR BACK EXIT
10
Indice
Altri manuali Wonwoo Telecamera di sicurezza
Wonwoo
Wonwoo ms 101 Manuale utente
Wonwoo
Wonwoo wsj-300 Manuale utente
Wonwoo
Wonwoo PS-M032 Istruzioni per l'installazione
Wonwoo
Wonwoo WCA series Manuale
Wonwoo
Wonwoo PS-100N Istruzioni per l'installazione
Wonwoo
Wonwoo WTK-M202 Manuale utente
Wonwoo
Wonwoo HDSC-S202M Istruzioni per l'installazione
Wonwoo
Wonwoo WCM-121N Istruzioni per l'installazione
Wonwoo
Wonwoo EB-363P Manuale utente
Wonwoo
Wonwoo EWSJ-E180 Istruzioni per l'installazione
