X-Micro XWL-11GRAR Manuale utente
WLAN 11g Broadband Router
User Guide
ver 1.0
This product is in compliance with the essential requirements
and other relevant provisions of the R&TTE directive 1999/5/EC.
Product Name: X-Micro WLAN 11g Broadband Router
Model Name : XWL-11GRAR
MAX. OUT POWER
COUNTRY CHANNELS INDOOR OUTDOOR
Spain 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
France 2400-2454 MHz 1-8 < 100 mW EIRP < 100 mW EIRP
France 2454-2483.5 MHz 9-13 < 100 mW EIRP < 10 mW EIRP
Italy 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
UK 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
Netherlands 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
Germany 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
Austria 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
Belgium 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
Switzerland 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
Luxemburg 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
Ireland 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
Portugal 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
Norway 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
Denmark 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
Finland 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
Iceland 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
Greece 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
Lichtenstein 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
Sweden 2400-2483.5 MHz 1-13 < 100 mW EIRP < 100 mW EIRP
FCC INFORMATION
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
The equipment has been tested and found to comply with the limits for a
Class B Digital Device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction, may cause
harmful interference to radio communication. However, there is no grantee that
interference will not occur in a particular installation. If this equipment dose
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Notice: The Part 15 radio device operates on a non-interference basis with
other devices operating at this frequency. Any changes or modification not
expressly approved by the party responsible could void the user’s authority to
operate the device.
REGULATORY INFORMATION
X-Micro WLAN 11g Broadband Router must be installed and used in strict
accordance with the instructions. This device complies with the following radio
frequency and safety standards.
USA - Federal Communications Commission (FCC)
This device complies with Part 15 of FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference that may cause undesired
operation.
1
Copyright
Copyright 2006 by X-Micro Technology Corp., All rights reserved. No part of
this publication may be reproduced, transmitted, transcribed, stored in a
retrieval system, or translated into any language or computer language, in any
form or by any means, electronic, mechanical, magnetic, optical, chemical,
manual or otherwise, without the prior written permission of X-Micro
Technology Corp.
Disclaimer
X-Micro Technology Corp. makes no representations or warranties, either
expressed or implied, with respect to the contents hereof and specifically
disclaims any warranties, merchantability or fitness for any particular purpose.
Any software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not this
company, its distributor, or its dealer) assumes the entire cost of all necessary
servicing, repair, and any incidental or consequential damages resulting from
any defect in the software. Further, X-Micro Technology Corp., reserves the
right to revise this publication and to make changes from time to time in the
contents hereof without obligation to notify any person of such revision or
change.
All brand and product names mentioned in this manual are trademarks and/or
registered trademarks of their respective holders.
2
Index
English……………………………………………….…..………………………..P.2
German…………………….……………………………......…………………P.12
French………………………………………………………..………………….P.21
Dutch……………………………………………………………..………………P.30
Italian…………………………………………………………………............….P.39
Spanish……………………………………………………………….....………P.48
Portuguese………….....................................………………………….……P.57
Russian…………….......................................………………….……P66
Traditional Chinese……………………………………………………….……P.75
3
§ Connect the wireless broadband router to your network
1. Connect the power adapter to the receptor at the back panel. Plug the
power adapter into the outlet. The power LED will turn on to indicate this
proper operation.
2. Power off your cable/ DSL modem. Using an Ethernet cable to connect the
Ethernet jack located on the cable/ DSL modem and the WAN port on the
back panel of this router. After this connection, please power on your cable/
DSL modem. The WAN PORT will illuminate to indicate the proper
operation
3. Insert an Ethernet cable to the LAN port on the back panel of the router and
an available Ethernet port on the network adapter in the computer that will
be used to configure the router. The LED light of LAN port1 will illuminate to
indicate the proper connection.
4. Then, restart your computer.
5. Connect your Ethernet-quipped computers to the remaining Ethernet LAN
ports on the back panel of this router with the additional Ethernet cables.
◆Back View:
◆LED Indicators:
LED Color Status Description
On Indicates proper connection to power
supply.
Power Green
OFF The unit is not receiving power
Status Green On
Indicates that the device is
connected to the WLAN.
On Indicates connection to the WAN port
WAN Blinking Data transmission.
On Link is established
On Blinking Packet transmit or receive activityWLAN
Off — No Link activity
4
On Indicates connection is established.
On Blinking Data transmissionsLAN
Off — No LAN connections
§ Quick Setup via Wizard
◆Open your Web Browser
You could start to access the configuration menu anytime by opening a web
browser window by typing the IP address of this wireless router. The default
IP is 192.168.1.1.
The below window will popup. Please enter the user name and password.
Both of the default is “admin”.
Now, the main menu screen is popup.
5
You can simply follow the step-by-step process to get your wireless router
configuration ready to run in 6 easy steps. Please click “Next” on the Setup
Wizard screen to continue.
◆Step 1: Set your new Password
You can change the password as you like and then click “Next” to continue.
6
◆Step2: Choose your time zone
Select your time zone from the drop down list. Please click “Next” to
continue.
◆Step 3: Set LAN connection and DHCP server
Set your IP address and mask. The default IP is 192.168.1.1. If you like to
enable DHCP, please click “Enabled”. DHCP enabled is able to
automatically assign IP addresses. Please assign the range of IP addresses
in the fields of “Range start” and “Range end”. Please click “Next” to
continue.
7
◆Step 4: Set Internet connection
Select how the router will set up the Internet connection: Obtained IP
automatically; Fixed IP address; PPPoE to obtain IP automatically; PPPoE
with a fixed IP address; PPTP.
Obtain IP automatically (DHCP client):
If you have enabled DHCP server, choose "Obtain IP automatically (DHCP
client)" to have the router assign IP addresses automatically.
Fixed IP Address:
Altri manuali per XWL-11GRAR
1
Indice
Lingue:
Altri manuali X-Micro Router wireless
X-Micro
X-Micro XWL-11GRAG Manuale utente
X-Micro
X-Micro Wireless LAN Broadband Router Manuale utente
X-Micro
X-Micro XBT-HS3X Manuale utente
X-Micro
X-Micro XWL-11GRAR Manuale utente
X-Micro
X-Micro XWL-11GRTX Manuale utente
X-Micro
X-Micro XWL-11GRTX Manuale utente
X-Micro
X-Micro XWL-11BRRG Manuale utente
X-Micro
X-Micro XWL-11BRRG Manuale utente
X-Micro
X-Micro XBT-DG2G Manuale utente
X-Micro
X-Micro XWL-11BRRG Manuale utente
