X-Vision XD401 Manuale utente
XD401
1000 User Digital Biometric ‘Fingerprint’
Access Control & Time/Attendance Unit
OPERATION MANUAL
p2
I. Introduction …………………………………… 3
1.1 Basic Concepts …………………………………… 4
1.1.1 User Enrollment …………………………………… 4
1.1.2 User Verification …………………………………… 4
1.1.3 Match Threshold Levels …………………………………… 4
1.1.4 User ID Numbers …………………………………… 5
1.1.5 Authority (status) Levels …………………………………… 5
1.1.6 Start-up window …………………………………… 6
1.2 How to place the finger …………………………………… 6
II. Enrollment and Verification Procedures …………………….......... 7
2.1 Enrolling User …………………………………… 7
2.2 Testing an Enrollment …………………………………… 11
2.3 Enrolling a fingerprint for backup ……………………………............ 12
2.4 Verifying Your Identity …………………………………… 12
2.4.1 Fingerprint Verification …………………………………… 12
2.4.2 Password Verification …………………………………… 13
2.4.3 ID & Fingerprint …………………………………… 14
2.5 Hints for Successful Enrollments ……………………………............ 14
III. System Options …………………………………… 15
3.1 System Options …………………………………… 15
3.1.1 Date Time …………………………………… 16
3.1.2 Language …………………………………… 16
3.1.3 Lock Controller …………………………………… 16
3.1.4 Advanced Options …………………………………… 16
3.2 Power Manager …………………………………… 17
3.3 Communication Option …………………………………… 18
3.4 Log Options …………………………………… 18
3.5 Auto Test …………………………………… 19
IV. System Information …………………………………… 19
V. Maintenance …………………………………… 20
TABLE OF CONTENTS
p3
I. Introduction
This chapter is about the Main Features of the XD401Fingerprint unit.
Product Appearance
Key Controls
•OK - Confirm key: Confirm your present operation.
•MENU - Menu key: Press down the key for seconds to enter the management
interface in the initial status.
•Cancel key: Cancel your present operation.
•Scrolling up key: Scrolling up the menu
•Scrolling down key: Scrolling down the menu
•IN -Check for ON of work
•OUT -Check OUT of work
•Power key: Control the power on and off
•Door bell
p4
1.1 Basic Concepts
This section contains definitions and descriptions of the XD401’s features, including:
· User Enrollment
· User Verification
· Match Threshold Levels
· User ID Numbers
· Authority (Status) Levels
The two most important XD401’s Functions are User Enrollment and User Verification.
1.1.1 User Enrollment
•Enrollment is the process to create an ID number and scanning a user’s finger to create
atemplate three times. This template is associated with a user ID number and stored.
•During user verification, the stored template is compared to the current fingerprint scan
to confirm the user’s identity.
•Enrollment is performed at designated units. The user can verify on the time recorder
that enroll his fingerprint. The enrollment process takes approximately 2 seconds.
•Up to ten fingers can be enrolled for the same ID number, so the user may have more
verifications way.
•Ideally, everyone finger on each hand should be enrolled so that if the user injures the
enrolled finger had, an alternate finger template is available. While recording the finger
type is optional, it is recommended such as left or right index, so that at verification the
user is prompted as to which finger to use.
1.1.2 User Verification
Verification occurs when a user either enters an ID number or places a finger in the
fingerprint sensor, then input password for comparison with the stored template.
1.1.3 Match Threshold Levels
The Mach Threshold is a number that represents the degree to which the verification is
examined to ensure that the person is the person claimed.
The Match Threshold Levels establishes a balance between False Acceptance Rate (FAR)
and False Rejection Rate (FRR). FAR measures how often a non-authorized user is falsely
recognized and granted access to the system. FRR measures how often an enrolled and
p5
authorized user, who should be granted access to the system, is denied on the basis
that the system did not recognize him.
• You can set match threshold levels on a per-use basis. For the fingerprint verification
is difficult, you can adopt ID & Fingerprint verification (match one to one).
•Raising the threshold increases security, while lowering it increases throughout. The
correct balance is essential.
• For users with worn or damaged fingers, match threshold levels can (and should) be
reduced.
•Different sites have different requirements.
Table 1—1 Suggested Match Threshold Settings
1.1.4 User
ID Numbers
Before beginning fingerprint enrollment, a user is assigned User ID Number. This ID
number is used to call up the fingerprint template each time that verification is
requested.ID numbers are normally called up via the keypad, but they can be called up
through other means such as RF Card.
1.1.5 Authority (status) Levels
XD401 has four authority or status levels:
•Users are people whose identity must be verified, such to gain access to a facility or
to have their attendance recorded.
•Enrollers are Users who are authorized to enroll new users or delete on to the
system.
•Managers can do other operations, except set advanced option and enroll manager’s
authority.
•Supervisors are Users who access to all functions and change all setup in the system.
Note: Without Manager and Supervisor status in the system, the Enroller will enroll
them. And if there isn’t a Supervisor in the system, the Manager will enroll him.
FRR FAR One-to-many One-to-one
High Low 45 25
Middle Middle 35 15
Low High 25 10
p6
1.1.6 Start-up window
Click the power button and the screen showed on, a display of a window was called the
Start-up window. The following appears:
1.2 How to place the finger
1. The correct way is:
Place a finger flat on the sensor surface
Place it to the center of the sensor surface
2. The wrong way is:
Vertical Offset
Inclined Lower
Note: Please adopt the correct way to place the finger. Xvision is not responsible for the
malfunctioning results arising from improper pressing manners. Our company reserve
ultimate the interpreting and modifying right for this.
Welcome
04
-
01
-
02 FRI
p7
II. Enrollment and Verification Procedures
This chapter describes how to enroll and verify users on the XD401 unit.
The following topics are included:
· Enrolling User
· Testing an Enrollment
· Enrolling a User with the Display Finger Option On
· Verifying Your Identity
· Hints for Successful Enrollments
Note: You must have Enroller, Manager, or Supervisor status to enroll users. For
information on status levels, see “Authority (Status) Levels” on 1.1.5.
2.1 Enrolling Users
If this is the first enrollment in a new or empty system, everyone will become an enroller.
If there is a manager in the system, you will have Manager status to enroll a new user.
There are three ways of enrollment, fingerprint enrollment, password enrollment,
fingerprint & password are suitable for three differences crowds.
•Fingerprint enrollment suited the most people who have better quality fingerprints;
•Fingerprint & Password suited few people who enrolling successful, but verification
was difficult;
•Passwordenrollment suited 1% people who verification unsuccessful.
To start the enrollment process, identify yourself firstly - press [Menu], enter your ID
number or fingerprint, and then verify your identity.
Note: If this is the first enrollment in a new or empty system, you will not be prompted for
verification.
The following message appears on the display:
Menu
ŹUser Manage
Options
Sys Info
U
p8
Press [OK], access the User Manager, the following message display:
Press [OK], access the User Enrollment, the following message display:
1. Fingerprint Enrollment
(1) Access the Enroll Fingerprint to press [OK], the following display:
(2) Press [OK], the following
appears:
(3) Input the enrolling
number (the range is 1 to
65534), press [OK], the
following appears:
User Manage
ŹEnroll User
Enroll Admin
Delete
Enroll User
ŹEnroll FP
Enroll Pwd
FP & Pwd
N
ew Enroll
Enroll No 00001
ESC OK
(
[], the following appears:
N
ew Enroll
Enroll No 00008
ESC OK
w
N
ew Enroll
Place Finger…
ESC
(
p9
(4) If the test is successful three times in a row, the following appears:
Note: 07711-1: The last number 1 means the first fingerprint.
Press [OK], the previous message continues to be displayed while the template is created.
If your identity cannot be verified, you are prompted to try again. And you must restart the
verification procedure (step 3).
2. Password Enrollment
(1) Access the password enrollment, press [OK], the following appears:
(2) Press [OK], the following appears:
(3) Input the enroll number (the range is 1 to 65534), press [OK], the following appears:
Note:
The password range is
1 to 5.
N
ew Enroll
00008-1
ESC OK [Save] T
Enroll Pwd
New Enroll?
ESC OK
N
ew Enroll
Enroll No 00008
ESC OK
(
N
ew Enroll
Input Pwd *****
ESC OK
p10
(4) Input the password, press [OK], the following appears:
(5) Input the password again, press [OK], the following appears:
Note: 00008-P: The last letter P means password.
Press [OK], the previous message continues to be displayed while the template is created.
3.Fingerprint & Password
(1) Access the Fingerprint& Password, press [OK], the following appears:
(2) Press [OK], the following appears:
(3) Input the password
(range is 1 to 65534), press
[OK], the following appears:
N
ew Enrollment
Input Pwd: *****
Pwd Affirm: *****
ESC OK
(
N
ew Enroll
00008-P
ESC OK [Save]
O h i
FP & Pwd
New Enroll
ESC OK
N
ew Enroll
Enroll No 00008
ESC OK
N
ew Enroll
Please finger…
ESC
Indice
Altri manuali X-Vision Portale
Manuali Portale popolari di altre marche
LST
LST M500RFE-AS Manuale utente
Kinnex
Kinnex Media Gateway Manuale utente
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuale utente
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuale utente
Telsey
Telsey CPVA 500 - SIP Manuale utente
