Xerox WorkCentre 5222 Manuale utente

Quick Network Setup Guide

This guide includes instructions for:

Quick Network Setup (DHCP) on page 1

Quick Network Setup (Static IP) on page 3

Note

For more detailed instructions, see the System Administration Guide.

Quick Network Setup (DHCP)

The System Administration Guide contains detailed information about network setups.

Prerequisites for Quick Network Setup Using TCP/IP

1. Confirm that an existing operational network utilizing TCP/IP is available.

2. Confirm that the Ethernet cable is plugged into the multifunction machine and into an

operational Ethernet port on the network.

Note

The Ethernet cable is an RJ45 type and is not supplied by Xerox.

Configuring an IP Address via DHCP

On startup, the multifunction machine defaults to DHCP to obtain its network configurations.

A DHCP server delivers an IP address, as well as other configuration settings to the machine.

If you use a DHCP server to allocate an IP address to the machine, then proceed as follows:

Procedure for Quick Network Setup Using TCP/IP

1. Power on the machine.

2. Wait a minute or so while the machine negotiates an IP address.

3. Print the Configuration Report:

a. Press the <Machine Status> button on the machine.

b. On the [Machine Information] screen, select [Print Reports].

c. Select [Printer Reports].

d. Select [Configuration Report].

e. Press the <Start> button on the machine.

XE3023EN0-2

Quick Network Setup (DHCP)

4. Read the Configuration Report to confirm that an IP address has been allocated and that

it is a valid IP address on your network.

Note

If the IP address starts with 169.xxx.xxx.xxx, then the DHCP server has not

properly allocated an address or DHCP is not enabled on your network.

5. Record the IP address allocated.

6. From a workstation, open a web browser (such as Internet Explorer), and then enter the

machine’s IP address. If connected properly, you should see the CentreWare Internet

Services web page for your machine.

Note

CentreWare Internet Services is a powerful tool for configuring the machine

remotely. The default user name is “11111” and the passcode is “x-admin”. The

user name and passcode are case sensitive and should be changed after install.

7. Load the print drivers on the computers that will be accessing the machine.

Quick Network Setup (Static IP)

Prerequisites for Manual Setup of Network Using Static IP Address

Note

On startup, the WorkCentre multifunction machine defaults to DHCP to obtain its

network configurations, so DHCP must be turned off by manually entering a static IP

address.

Before installing, record the following information for use during setup:

Note

To obtain this information, contact your System Administrator.

Procedure for Manual Setup of Network Using Static IP Address

1. Power on the machine.

2. Press the <Log In/Out> button on the control panel, and then type the System

Administrator login ID to enter the System Administration mode.

Note

The passcode may also be required depending on the machine configuration.

3. Press the <Machine Status> button on the control panel, and then select the [Tools] tab

on the screen.

4. Select [System Settings] in the menu at the left side of the screen.

5. Select [Connectivity & Network Setup] in the [Group] menu.

6. Select [Protocol Settings] in the [Features] menu.

7. Under [TCP/IP - IP Mode], select [IPv4 Mode], [IPv6 Mode], or [Dual Stack].

When IPv4 Mode or Dual Stack is selected in step 7.

a. Select [IP Address Resolution], and then [Change Settings].

b. Select [STATIC], and then select [Save].

c. Select [IPv4 - IP Address], and then [Change Settings].

TCP/IP Address:

Gateway Address:

Subnet Mask (for IPv4) / Prefix (for IPv6):

DNS Server Address:

Quick Network Setup (Static IP)

d. Use the keypad on the screen to enter the IP Address for the machine in the format

"xxx.xxx.xxx.xxx". Select [Save].

e. Select [IPv4 - Subnet Mask], and then [Change Settings].

f. Using the same method as in step d., enter the Subnet Mask.

g. Select [IPv4 - Gateway Address], and then [Change Settings].

h. Using the same method as in step d., enter the Gateway Address.

Note

If you do not wish to set the gateway address, leave this field blank.

i. Select [IPv4 - IP Filter], and then [Change Settings].

j. Select [Enabled] to filter access to the machine.

Note

If you do not wish to use the IP filter feature, select [Disabled].

k. When you have finished establishing TCP/IP, select [Close] on the [Protocol

Settings] screen.

When IPv6 Mode or Dual Stack is selected in step 7.

a. Set [IPv6 Address Manual Configuration] to [Enabled].

b. Select [Manually Configured IPv6 Address], and then [Change Settings].

c. Use the keypad on the screen to enter an IP Address for the machine in the format

"xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx". Select [Save].

d. Select [Manually Configured IPv6 Prefix], and then [Change Settings].

e. Enter an IP address prefix, and then select [Save].

f. Select [Manually Configured IPv6 Gateway], and then [Change Settings].

g. Using the same method as in step c., enter a Gateway Address.

h. Select [IPv6 - IP Filter], and then select [Enabled] or [Disabled].

Note

If you do not wish to use the IP filter feature, select [Disabled].

i. When you have finished establishing TCP/IP, select [Close] on the [Protocol

Settings] screen.

Altri manuali per WorkCentre 5222

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Xerox Stampante tutto in uno

Xerox

Xerox Color Qube 9201 Manuale utente

Xerox

Xerox Xerox Phaser 6600 Manuale operativo e di manutenzione

Xerox

Xerox WorkCentre 7200 series Manuale utente

Xerox

Xerox WorkCentre 5945 Manuale operativo e di manutenzione

Xerox

Xerox VersaLink C70 Series Manuale utente

Xerox

Xerox WorkCentre 6027 Manuale operativo

Xerox

Xerox Phaser 3600 Manuale utente

Xerox

Xerox WorkCentre PE16 Manuale utente

Xerox

Xerox 5700 Series Manuale utente

Xerox

Xerox WorkCentre 4265 Manuale operativo

Xerox

Xerox WorkCentre XE88 Manuale utente

Xerox

Xerox DocuColor 252 Manuale di istruzioni e di sicurezza

Xerox

Xerox WorkCentre Pro 423E Manuale utente

Xerox

Xerox ColorQube 9201 Manuale del proprietario

Xerox

Xerox PHASER 8560MFP Manuale

Xerox

Xerox WorkCentre 3655i Manuale

Xerox

Xerox DocuColor 12/DCCS50 Manuale utente

Xerox

Xerox 3100MFPX - Phaser B/W Laser Manuale utente

Xerox

Xerox WorkCentre 5765 Manuale

Xerox

Xerox WorkCentre 3315 Manuale operativo

Xerox

Xerox DocuColor 2240 Manuale utente

Xerox

Xerox WORKCENTRE 7428 Manuale di istruzioni

Xerox

Xerox ColorQube 9201 Manuale utente

Xerox

Xerox WorkCentre Pro 412 Manuale utente

Manuali Stampante tutto in uno popolari di altre marche

Triumph Adler

Triumph Adler DC 2016 Manuale

Epson

Epson WorkForce WF-2510 Guida utente

Epson

Epson Stylus Scan 2000 Manuale di installazione e funzionamento

Epson

Epson PictureMate Snap PM 240 Manuale di istruzioni

Konica Minolta

Konica Minolta bizhub C35 Manuale utente

Brother

Brother MFC-J430w Manuale utente

Konica Minolta

Konica Minolta BIZHUB 558 Manuale utente

Lexmark

Lexmark MX710 Series Manuale

Brother

Brother MFC-9760 Manuale utente

Lexmark

Lexmark XC8155 Manuale utente

Lexmark

Lexmark X642E Manuale utente

Sharp

Sharp MX-2310U Guida

Aficio

Aficio 200 Manuale utente

Canon

Canon ImageCLASS 2300 Manuale

Ricoh

Ricoh Pro C900 Manuale utente

Lexmark

Lexmark X925 Manuale utente

Brother

Brother Business Smart MFC-J4510dw Manuale utente

Epson

Epson Stylus CX8400 Series Manuale utente