Xerox WORKCENTRE C2424 Manuale utente
WorkCentre® C2424 Copier-Printer
Copyright © 2005 Xerox Corporation. All Rights Reserved.
A-1
Your system and the recommended supplies have been designed and tested to meet strict safety
requirements. Attention to the following information will ensure the continued safe operation
of your system.
Electrical Safety
■Use the power cord supplied with your system.
■Plug the power cord directly into a properly grounded electrical outlet. If you do not know
if an outlet is grounded, ask an electrician to check the outlet.
■Do not use a ground adapter plug to connect the system to an electrical outlet that does not
have a ground connection terminal.
■Do not use an extension cord or power strip.
Warning
Avoid the potential of electrical shock by ensuring that the system is properly grounded.
Electrical products may be hazardous if misused.
■Do not place the system in an area where people might step on the power cord.
■Do not place objects on the power cord.
■Do not block the ventilation openings. These openings are provided to prevent overheating
of the system.
■Do not drop paper clips or staples into the system.
Warning
Do not push objects into slots or openings on the system. Making contact with a voltage
point or shorting out a part could result in fire or electrical shock.
If you notice noises or odors that are not associated with your normal system operation:
1. Turn off the system immediately
2. Disconnect the power cord from the electrical outlet
3. Call an authorized service representative to correct the problem.
User Safety
WorkCentre® C2424 Copier-Printer
A-2
The power cord is attached to the system as a plug-in device on the side of the system. If it is
necessary to disconnect all electrical power from the system, disconnect the power cord from
the electrical outlet.
Warning
Do not remove the covers or guards that are fastened with screws unless you are installing
optional equipment and are specifically instructed to do so. Power should be OFF when
performing these installations. Disconnect the power cord when removing covers and
guards for installing optional equipment. Except for user-installable options, there are no
parts that you can maintain or service behind these covers.
The following are hazards to your safety:
■The power cord is damaged or frayed.
■Liquid is spilled into the system.
■The system is exposed to water.
If any of these conditions occur:
1. Turn off the system immediately.
2. Disconnect the power cord from the electrical outlet.
3. Call an authorized service representative.
Maintenance Safety
■Do not attempt any maintenance procedure that is not specifically described in the
documentation supplied with your system.
■Do not use aerosol cleaners. The use of supplies that are not approved may cause poor
performance and could create a hazardous condition.
■Do not burn any consumables or routine maintenance items. For information on Xerox
supplies recycling programs, go to www.xerox.com/gwa.
Operational Safety
Your system and supplies were designed and tested to meet strict safety requirements. These
include safety agency examination, approval, and compliance with established environmental
standards.
Your attention to the following safety guidelines helps to ensure the continued, safe operation
of your system.
System Supplies
■Use the supplies specifically designed for your system. The use of unsuitable materials
may cause poor performance and a possible safety hazard.
WorkCentre® C2424 Copier-Printer
A-3
■Follow all warnings and instructions marked on, or supplied with, the system, options and
supplies.
Caution
Use of other than Genuine Xerox WorkCentre C2424 Solid Ink may affect print and copy
quality and system reliability. It is the only ink designed and manufactured under strict
quality controls by Xerox for specific use with this system. The Xerox Warranty, Service
Agreements, and Total Satisfaction Guarantee do not cover damage, malfunction, or
degradation of performance caused by use of non-Xerox supplies or consumables, or the
use of Xerox supplies not specified for this system.
Note
The Total Satisfaction Guarantee is available in the United States and Canada.
Coverage may vary outside these areas; please contact your local representative for
details.
System Location
■Place the system in a dust-free area within a temperature range of 50 degrees F to
90 degrees F (10 degrees C to 32 degrees C) and a relative humidity range of 10 percent to
80 percent.
■Place the system in an area where there is adequate space for ventilation, operation, and
servicing. The recommended minimal spacing is:
■30 cm (11.8 in.) above, measuring from the top of the document feeder
■24 cm (9.5 in.) behind
■10 cm (3.9 in.) on the left side of the system
■37 cm (14.6 in.) on the right side of the system, to allow access to the maintenance
unit and waste tray.
■Do not block or cover the slots and openings on the system. The system may overheat
without adequate ventilation.
■For optimum performance, use the system at elevations below 2,438 m (8,000 ft.).
■Do not place the system on a carpeted location such as a carpeted floor. Airborne carpet
fibers can be pulled into the system and cause print- and copy-quality problems.
■Do not place the system near a heat source.
■Do not place the system in direct sunlight.
■Do not place the system in line with the cold air flow from an air conditioning system.
■Place the system on a level, solid non-vibrating surface with adequate strength for the
weight of the system. It should be within 2 degrees of horizontal with all four feet in solid
contact with the surface. The base system weight without any packaging materials is
approximately 42 kg (93 lbs.).
WorkCentre® C2424 Copier-Printer
A-4
Moving the System
Caution
Parts of the system are hot. To avoid personal injury or damage to the system, allow the
ink to solidify. Run the shut-down procedure to cool the system quickly. Wait at least
30 minutes for the system to cool completely before moving or packing it.
■Always allow the system to cool before it is moved to avoid ink spills which can damage
the system.
■Use the shut-down procedure at the control panel (Shut Down for Moving System)
for best results.
■Never move the system if you receive a Power Down Error-Head not Parked
message at the system’s control panel. This message means the system is not ready to be
moved. If the printhead is not locked, the system can be damaged during shipment.
■Always turn off the system using the power switch, located under the interface cover on
the right side of the system, and unplug all cables and cords. Do not turn off the system by
pulling the power cord or using a power-strip with an on/off switch.
■Always secure the scanhead shipping restraint on the left side of the scanner to lock the
scanhead before removing the scanner portion of the system. Shipping the scanner with
the scanhead unlocked can damage the scanner.
■Always remove the document feeder before shipping the system.
■Always remove the scanner before shipping the system.
2424-107
Output Color
Mode
2-Sided
Output
Quality
Original
Type
Graphics
Prod
Hi-Res
Enhansed
Standard
Fast
B/W
Color
Uncollated
Collated
WorkCentre® C2424 Copier-Printer
A-5
■The system is heavy and must be lifted by two people. The illustration below shows the
proper technique for lifting the system.
■Always move the system separately from optional Trays 3 and 4.
When shipping the system, repack the system using the original packing material and boxes or
a Xerox repackaging kit. Additional instructions for repacking the system are provided in the
repackaging kit. If you do not have all the original packaging, or are unable to repackage the
system, contact your local Xerox service representative.
Caution
Failure to repackage the system properly for shipment can result in damage to the
system. Damage to the system caused by improper moving is not covered by the
Xerox warranty, service agreement, or Total Satisfaction Guarantee. The Total
Satisfaction Guarantee is available in the United States and Canada. Coverage may
vary outside these areas; please contact your local representative for details.
Operating Safety Guidelines
■Keep hands, hair, neckties, etc., away from the exit and feed rollers.
■Do not remove the paper source tray that you selected in either the printer driver or control
panel.
■Do not open the doors while the system is busy.
■Do not move the system while busy.
2424-109
42 kg
93 lbs.
WorkCentre® C2424 Copier-Printer
A-6
Symbols Marked on the System
Danger, high voltage.
Use caution (or draws attention to a particular
component). See the manual(s) for information.
Avoid pinching fingers in the system. Use
caution to avoid personal injury.
Keep hands clear to avoid personal injury.
Hot surface on or in the system. Use caution to
avoid personal injury.
Altri manuali per WORKCENTRE C2424
24
Indice
Altri manuali Xerox Stampante tutto in uno
Xerox
Xerox WorkCentre 6025 Manuale operativo
Xerox
Xerox WorkCentre 3315DN Manuale utente
Xerox
Xerox WorkCentre 6655 Manuale di servizio
Xerox
Xerox WorkCentre M24 Color Manuale utente
Xerox
Xerox VersaLink B7025 Manuale operativo
Xerox
Xerox WorkCentre 5022 Manuale utente
Xerox
Xerox WorkCentre 4260S Manuale utente
Xerox
Xerox WorkCentre 6027 Manuale utente
Xerox
Xerox WorkCentre 7346 Manuale utente
Xerox
Xerox AltaLink C81 Series Manuale utente
Xerox
Xerox WORKCENTRE 7775 Manuale utente
Xerox
Xerox WORKCENTRE 7120 Manuale utente
Xerox
Xerox WorkCentre 4260S Manuale utente
Xerox
Xerox Copycentre C118 Manuale utente
Xerox
Xerox Document Centre 50 Manuale di istruzioni
Xerox
Xerox ColorQube 9300 series Manuale utente
Xerox
Xerox WorkCentre M24 Color Manuale utente
Xerox
Xerox PHASER 3635 Manuale utente
Xerox
Xerox WorkCentre 6015NI Manuale utente
Xerox
Xerox VersaLink C505 Manuale utente
Manuali Stampante tutto in uno popolari di altre marche
Triumph Adler
Triumph Adler DC 2016 Manuale
Epson
Epson WorkForce WF-2510 Guida utente
Epson
Epson Stylus Scan 2000 Manuale di installazione e funzionamento
Epson
Epson PictureMate Snap PM 240 Manuale di istruzioni
Konica Minolta
Konica Minolta bizhub C35 Manuale utente
Brother
Brother MFC-J430w Manuale utente
