Xinje DS3 series servo Manuale utente

Xinje Electronic Co., Ltd.

DS3 series servo

User manual

No. SC309 20090706 1.0

DS3 series servo manual

►► Safety notes

 Confirmation after get the products

 If servo drive is missing parts, broken, type wrong, please do not install it.

 Installation

 Cut off all the power before installation.

 Wiring

 Cut off all the power before wiring.

 Connect the AC power to the power terminals on the servo drive.

 Do not connect output terminal U, V, W of servo drive to 3-phase power.

 Ground the servo drive with 2mm2 cables.

 Running and maintenance

 Please install the panel guard when power on.

 Do not touch the terminals within 5 minutes after power off.

 Do not connect servo drive with loader when test-running.

 After connect to the loader, please set suitable parameters before running.

 Do not change the wiring when power on.

 Do not touch the radiator when running.

►► Product arrival confirmation

1. Confirm the product as the following items.

Item Remark

The product type is accord with the

ordered one

Please confirm the label of servo drive and motor

Servo motor rotation axis is turning well Can turn by manual. Cannot turn with brake

Is the product broken? Please check if there is broken because of

transportation

Is the screw loose? Check the screw with screw driver

Motor code Check the motor code on servo drive and motor, if

they are the same

If there is inconsistent item, please contact XINJE sales department.

DS3 series servo manual

2. Type

1) Servo drive

DS3 – 2 1P8

Suitable motor capacity

0P7: 0.75KW, 1P5: 1.5KW, 1P8: 1.8KW, 2P7: 2.7KW

Voltage level: 2: 220V, 4: 380V

Servo series name: DS3: standard type

2) Servo motor

MS -110 ST - M 06030 A Z- 2 1P8

Power

Voltage level

Power-loss brake

Shaft

Feature code

Feedback part code

Sine drive motor

Base No.

Motor series name

Base No.: 60, 80, 110, 130;

Feedback part code: M (optical pulse encoder)

Feature code: first 3-bit means rated torque; last 2-bit means rated speed

00630: rated torque 0.6N·m, rate speed: 3000rpm

02430: rated torque 2.4N·m, rate speed: 3000rpm

06030: rated torque 6.0N·m, rate speed: 3000rpm

10015: rated torque 10.0N·m, rate speed: 1500rpm

Shaft type: A-no key, B-with key

Power-loss brake: vacant-no, Z-with DC99V power-loss brake

Voltage level: 2－220V, 4-380V

Power: 0P2-0.2KW; 0P4-0.4KW; 0P7-0.75KW; 1P5-1.5KW; 1P8－1.8KW

DS3 series servo manual

3. Part name

1) Servo motor

2) Servo drive

Power LED: turn on when servo drive is power on.

Charge LED: turn on when servo drive is power on. After power off, it will be on until there is

no charge in the capacitance of servo drive. At this time, please do not touch the servo drive.

Panel display: to display the servo state, alarm and parameters.

Panel button: to set the parameters.

COM1: connect to PC to debug the servo.

DS3 series servo manual

CN2: connect the encoder.

CN1: command input, sequence I/O signal

Power and servo motor terminals: to connect the power supply and power cable of servo

motor.

COM2: connect with PLC, HMI, ect.

►► Installation

1. Servo motor

MS series servo motor can be installed vertical or horizontal. If it is installed unsuitable or is in

wrong location, the motor life will be shortened.

1) Storage temperature

Please store the motor in the range of -20~+60℃

2) Installation location

MS series servo motor should be installed under below location:

 Indoor, no corrosive, flammable, explosive gas

 Good ventilation, less dusts, humidity

 Ambient temperature is in the range of 0~50 ℃

 Relative humidity is in the range of 20%~90% RH, no condensation

 Easy to clean and check

3) Concentricity

Please use coupler when connect to the machine, make the shaft center of motor and

machine on the same line. The installation of motor should be accord with the below

requirements.

Notes:

Please clear the antirust on the shaft with

thinner before install the motor. The thinner

cannot touch other parts of motor.

DS3 series servo manual

If the concentricity is not enough, it may cause vibration and damage the shaft.

Do not impact the motor shaft when install the coupler. Otherwise the monitor on the other

end of loader shaft will be broken.

4) Installation direction

MS series servo motor can be installed vertical or horizontal.

5) The solution to prevent from water or oil drops

6) The tension of the cables

Do not make large tension for the cable especially for the 0.2mm2, 0.3mm2 cables.

2. Servo drive

DS3 series servo drive is base-type. Please install it correctly otherwise there will be error.

1) Storage temperature

Store the servo drive in the range of -20~+85 ℃.

2) Installation location

Install the drive as the following item:

Location Notes

Install in the

control panel

Design the control panel size, servo configuration and cooling mode,

to decrease the ambient temperature under 50

℃

If close to the

heater

to decrease the ambient temperature under 50

℃

Seal the through part of the shaft. Please

order the motor with oil sealed.

DS3 series servo manual

If close to the

vibration

Install the shockproof device on the installation side of servo drive

If close to the

corrosive gas

To prevent the corrosive gas from the servo drive, otherwise there will

be error for the circuit.

Others Do not install in the location of high temperature, high humidity, full of

dusty and metal powder.

3) Installation direction

The direction must be vertical to the wall. Cool the servo by natural convection or fan.

4) Installation standard

Please install the servo drive as the below figure.

DS3 series servo manual

Direction of servo drive

The front side must face to the operator, and be vertical to the wall.

Ambient in the control cabinet:

 Temperature: 0～50 ℃

 Humidity: below 90% RH

 Vibration: 4.9m/s2

 No freeze and condensation

 Using temperature: 50 ℃

►► Dimension

1. Servo motor

(1) MS-80ST-M02430□□-20P7 installation dimension Unit: mm

DS3 series servo manual

(2) MS-110ST-M06030□□-21P8 installation dimension Unit: mm

Type LA

MS-110ST-M06030□□-21P8 219

(3) MS-130ST-M10015□□-21P5 installation dimension Unit: mm

Type LA

MS-130ST-M10015□□-21P5 213

Altri manuali per DS3 series servo

Indice

Altri manuali Xinje Servoazionamento

Xinje

Xinje DP-708 Manuale utente

Xinje

Xinje DP3C Series Manuale utente

Xinje

Xinje DS5C Series Manuale utente

Xinje

Xinje DS5K Series Manuale utente

Xinje

Xinje DS2 series Manuale utente

Xinje

Xinje DS2 series Manuale utente

Xinje

Xinje DS5B Series Manuale utente

Xinje

Xinje DS5F Series Manuale utente

Xinje

Xinje DS2 series Manuale utente

Xinje

Xinje DS2-20P7-AS Manuale utente

Xinje

Xinje DS2-45P5-A Manuale utente

Xinje

Xinje DF3E Series Manuale utente

Xinje

Xinje DS3 series servo Manuale utente

Xinje

Xinje DS5E Series Manuale utente

Xinje

Xinje DS3 series servo Manuale utente

Xinje

Xinje DS5K Series Manuale utente

Xinje

Xinje DS2-20P2-AS Manuale utente

Xinje

Xinje DS5L1 Series Manuale utente

Manuali Servoazionamento popolari di altre marche

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J5 MR-J5-G Series Manuale utente

Robotis

Robotis XH430-W350-T Manuale utente

NTI AG

NTI AG LinMot C1250 Series Manuale utente

Welcon

Welcon WE2A D048 Series Manuale utente

Parallax

Parallax 900-00005 Manuale utente

Festo

Festo TP 1410 Manuale utente

Axor

Axor MAGNUM 400 Manuale utente

Siemens

Siemens SINAMICS S120 Manuale utente

Danfoss

Danfoss 176F6494 Manuale utente

THORLABS

THORLABS TDC001 Manuale utente

TECO

TECO JSDAP Series Manuale utente

Rockwell Automation

Rockwell Automation Allen-Bradley Kinetix 6000 Manuale utente

GSK

GSK DA98D Manuale utente

Lenze

Lenze m850 Guida

Baumuller

Baumuller b maXX 3000 Manuale

Baumuller

Baumuller b maXX 5000 Manuale

Baumuller

Baumuller b maXX 5500 Manuale

Danfoss

Danfoss VLT HVAC Drive FC 102 Manuale utente