XSPC H2 Manuale utente
H2 Tower+
XSpc®
Component list
Contents
Page 3 - 5
Accessories Page 5 - 6
Preparing the base panel Page 7
Preparing the back panel Page 8
Preparing the ront panel Page 9
Attaching the back panel Page 10
Attaching the ront panel Page 11
Fitting the beams Page 13
Fitting the motherboard tray Page 15
Fitting the side panels Page 16
Radiator placements Page 17
XSpc Page 1
Troubleshooting Page 18
Attaching the center panel Page 12
Attaching the HDD cage Page 14
Introduction
XSpc Page 2
The XSPC H2 is a PC case speci ically designed or high end PC watercooling. It
can support a quad, single and triple 120mm radiator, while leaving plenty o
space or tubing routing. The case is supplied in lat pack orm, so you will need
a little time and patience to get it set up correctly. Assembly should take 1-2
hours, depending on your experience level.
This manual gives step by step instructions or assembling the H2 case. It is
advisable to read all the way through the instructions at least once be ore you
start assembly. It will save time in the long run.
When you are ready to begin installation, you should irst unpack the box and
check that no components are missing (see pages 3-6). I any parts are missing
rom the box please contact XSPC technical support.
www.xspc.biz/support
Speci ication
Dimensions:
618.9 x 246.6 x 696.8mm
Material:
Brushed aluminium – Black anodized
Screw size:
6-32 UNC
Features:
8x 5.25“ bays *
3x HDD bays (6x with optional extra HDD cage.)
1x SSD tray (up to 6x with optional extra trays)
6x 120mm an grills
- 1x Quad 120mm
- 2x Single 120mm
1x Acrylic window
*Front 5.25“ bay covers sold separately
[A] Base Panel x1
[D] Top Panel x1
[C] Front Panel x1
[E] Right Panel x1 [F] Left Panel x1
[B] Back Panel x1
Component List
XSpc Page 3
[ ] MB Cover Panel x1 [H] PCI Panel x1
[I] Motherboard Tray x1 [J] HDD Rack x1
[L] L Beam x2[K] 5.25“ Bay Sides x2
XSpc Page 4
SSD Tray x1 Castors x4
Accessories
XSpc Page 5
[M] Center Panel x1 [N] MB Support Beam x1
[O] PSU Panel x1 [P] Support Bracket x1
Part 1: Preparing the Base Panel
XSpc Page 7
Take panel [A] and place it on a
flat surface, protected by a clean
sheet.
Place a castor under a corner of
the panel and line up the 4 holes.
Put a screw through each hole.
On the underside of the panel
attach a washer and a nut to each
screw and tighten using a
screwdriver.
Repeat the process for each of
the four castors.
1 2
34
Part 2: Preparing the Back Panel
XSpc Page 8
Put panel [B] on a flat surface
facing upward.
Place panel [ ] over panel [B]
and line up the six holes.
Attach panel [ ] using four 6-32
thumb screws.
1 2
3
Part 3: Preparing the Front Panel
XSpc Page 9
Place panel [C] facing down on a
flat surface.
Take the [K] bay cage and attach
it using 6 countersunk screws.
You will need to use a small
screwdriver due to limited space.
Flip the panel over and thread the
power cables through the hole on
the front.
On the reverse side place an o-
ring and nut over the switch then
tighten the nut.
12
3 4
5
Altri manuali per H2
1
Indice
Altri manuali XSPC Allegato
