XtendLan SDOMEOAT2-SD332 Manuale utente

High Speed Dome

User Manual

SDOMEOAT2-SD332

2/16

Before Installing

Installation should be carried out only by qualified personnel and in accordance

with any wiring regulations in force at the time.

Please read this instruction and warnings before installing.

Do not attempt to service or repair the speed domes as opening or removing

covers may expose dangerous voltages or other hazards. Refer all servicing to

qualified service personnel.

Adequate protection against lightning strikes and power surges must be installed

to prevent damage to the speed dome.

Key Features

360º Panning, speed is 0.1º-300º/s.

Auto flip 180º

128 presets, the error of preset will less than 0.1º

4 dynamic privacy zones

Auto cruise by preset, the dwell time is 1s-250s.

Image freeze while panning

Manifold of scan, scan speed could be setting from 1º/s to 80º/s

Left and right limit scan.

7 alarm input and 2 relay output.

Easy fixing configuration

24V power supply built in

Static proof and thunder proof design of the RS485 connector and video

connecter.

3/16

Environmental requisition:

Operation Temperature: -40-+60

Humidity: <90%

Air pressure: 86-106Kpa

Power supply:AC24V/2.5A, 50/60Hz

The system setting Camera and

Switch SW1 address switch

Alarm connector 8P Short connector

RS485 communication 2P

AC24V power supply

AUX 4P

1、Power supply and

communication cable:：

AC24V

AC24V RS485

2、Video output：

Alarm signal

Alarm Relay Output “AUX1”

Alarm Relay Output “AUX2

Alarm Input GND

Alarm input signal l -7

AL1、AL2、AL3、AL4…AL7：Alarm input.

4/16

1, Dome setting Instruction

The switch setting SW1 ON=1 OFF=0

Protocol setting

Baud rate setting

Alarm

Alarm mode

DIP Switch

SW1234=

0000=PELCO-D/PELCO-P Auto

identify

SW5,6=

00=2400

01=4800

10=9600

11=19200

1=Alarm

enable

0=Alarm

disable

1=Always short

circuit.(Alarm

while open)

0=Always

open

circuit.(Alarm

while short)

Note

：

PELCOD PELCOP could be identifying automatically. On and off is the corresponding

switch position.

SW2 switch: address switch table.

CAM ID

OFF

∶

128

129

OFF

∶

255

OFF

256

5/16

High Speed Dome

Ver：1 00

PELCO D P

2400

ID：001

Tilereference OK

Pan reference OK

SONY FCB-EX480CP

Alarm

7 alarm input. The dome will alarm when alarm input port connect the GND. The AUX will be

closed when has alarm, and open when on alarm in. The capacitance of the relay isAC24V/1A.

The relay output:

2 relay switchAUX1,AUX2, the biggest capability is AC24V/1A. AUX1 connect with the alarm, the

master or keyboard controlsAUX2.

Camera Module Setting Switch

The dome can be fit different camera, and they have different

switch.

Camera

Switch 1

Switch 2

Switch 3

Switch 4

DIP-1

DIP-2

DIP-3

DIP-4

SONY

OFF

HITACHI

OFF

CNB-200L

OFF

CNB-M1560

OFF

SAMSUNG

(SDM300/SDM330)

OFF

Note: Please make sure the camera parameters are correct or the camera cannot work

or cannot work well. If this, please enter the camera menu and restore factory settings first,

then setting the parameters as request.

High Speed Dome Operation,

When Electric

When electric the dome, the version, protocol, baud rate, ID will display on the monitor, and the

dome will check automatic with vertical and level then display the specs of camera.

Example:

6/16

Camera ►

Pan ►

Shortcut Key

Self act

Nothing

Leisure Time

030

The operation way by keyboard controller

Function

Control

Level/Vertical

Joystick left, right/ up and down

OSD Confirm

OPEN

Cancel and Back

OSD Display

Call 95 preset

Zero Position

Call 34 preset

Level Scan

Call 99 preset

Auto Flip

Call 33 preset

Left limit: call 92 preset

Level Scan Limit

Point

Right limit: call 93 preset

Call preset scan 1

Call 81 preset

Call preset scan 2

Call 82 preset

Call preset scan 3

Call 83 preset

Call preset scan 4

Call 84 preset

Camera mode 1

Call 100 preset

Camera mode 2

Call 101 preset

Camera mode 3

Call 102 preset

4 Privacy mask, only fit to SONY480, SONY980 and HITACHI454 camera.

Level area increase: FAR

Level area reduce: NEAR

Vertical area increase: TELE

Privacy Mask

Vertical area reduce: WIDE

OSD Operation

1, Enter OSD

Please call the number 95 preset to display the OSD on the screen.

At figures the current item, figures the enabled item, and the ► after the item which have

submenu. You can change the item state when it has been enabled. Please press OPEN key to

enter or confirm and CLOSE key to back or cancel, and the key UP and DOWN control the cursor

up and down.

2 Menu function instructions

Call the number 95 preset to enter the OSD, and you also could set the shortcut key to display the

OSD.

Main Menu

7/16

Exposure ►

White Balance ►

Privacy ►

Other ►

Camera Model ►

Zoom Speed

005

Focus Speed

001

Exp Mode

Auto

Shutter speed

006

Iris

016

Gain

001

Bright

016

Back Light

Off

Slow Shutter

Off

Exposure ►

White Balance ►

Privacy ►

Other ►

Camera Model ►

Zoom Speed

005

Focus Speed

001

Camera OSD

Camera ► Press OPEN to enter the camera menu.

Camera Exposure

Exposure ►Press OPEN key to enter the camera exposure submenu.

Exposure operation

1, How to change the exposure

Exp Mode press OPEN key, enable Exp Mode, then

operate up and down by the joystick, the parameters are:

Auto, Manual, Shutter, Iris and bright

2 Confirm Exposure.

Exp Mode press OPEN key, select effect, the

menu change to Exp Mode

3 Cancel Exposure

Exp Mode press CLOSE to cancel the Exposure mode change, the menu change to

Exp Mode

Back the main camera menu

Exp Mode press CLOSE key to cancel the last menu.

Other operation of Exposure Menu

Exp Mode, control the joystick up or down to let the up and down, press OPEN key to

enable the item, then go on control up and down with joystick, and press OPEN key to confirm,

the cursor will change to .

White Balance

The dome has the function of Manual White Balance and Auto White Balance.

White Balance ► press OPEN key, enter the White

Balance submenu, then change the parameter,

WB Mode Auto

R Gain 214(0-255)

B Gain 175(0-255)

8/16

WB Mode

Auto

R Gain

210

B Gain

175

WB Mode

Auto

R Gain

210

B Gain

175

WB Mode

Auto

R Gain

210

B Gain

175

Exposure ►

White Balance ►

Privacy ►

Other ►

Camera Model ►

Zoom Speed

005

Focus Speed

001

Privacy1

Privacy2

Privacy3

Privacy4

White Balance Mode operation:

1、WB Mode

2、At WB Mode, press OPEN key to enable the Exp

Mode menu, then it will change to WB Mode,

control the joystick to change the parameter which

order is: Auto, Manual, ATW, OPW, Outdoor and

Indoor. R Gain

3, R Gain

At WB Mode, operate the joystick down let the

cursor come to R Gain, press OPER key to enter the

menu. Then operate the joystick up (increase) and down

(reduce) the R Gain. The homologous parameter is 0-255.

Press OPEN key to confirm and back or press CLOSE to

cancel and back.

4, B Gain

At WB Mode operate the joystick to control the

cursor come to B Gain, press OPEN key to enter the B

Gain setting, joystick up and down to increase and reduce

the parameter which from 0-255. Press OPEN key to

confirm and back or press CLOSE to cancel and back.

Privacy Mask

At Exposure ► operate the joystick to let the

cursor come to Privacy press OPEN to enter the

submenu, then set the parameter.

There are 4 privacy masks, which have the same

operation.

1, Set privacy mask

At the submenu of the Privacy, press OPEN key to enter

the adjust image, adjust the privacy zone by OPEN

(confirm), CLOSE (cancel), FAR (level increase), NEAR

(level reduce), TELE (vertical increase), WIDE (vertical

reduce). Then press OPEN key to confirm and back.

图:2.3.4

9/16

Digital Zoom

Auto ICR

Off

ICR

Off

Display

Off

Camera Mode Save：

Day Mode

Night Mode 1

Night Mode 2

Camera Mode Exec：

Day Mode

Night Mode 1

Night Mode 2

Privacy ►

Other ►

Camera Model ►

Zoom Speed

005

Focus Speed

001

Exposure ►

White Balance ►

Privacy ►

Other ►

Camera Model ►

Zoom Speed

005

Focus Speed

001

2, Clare privacy masks.

a, Restart the speed dome, all of the privacy mask will be cleared.

b, Enter the menu of the Privacy mask, press OPEN key to enter and press CLOSE to clear

the privacy mask you want to clear.

Others of the Camera menu

Press OPEN key to enable the submenu, operate

joystick to change the states of ON and OFF. Press

OPEN to confirm and back and CLOSE to cancel and

back.

Camera Mode

Camera Mode setting menu:

Press OPEN to enter the menu.

There are three mode under the Camera Mode Save

menu, move the cursor to the mode going to be change,

press OPEN the cursor will change to , the setting will

be saved and it will back to after 1 second.

The three items under Camera Mode Exec is opposite

the three modes above. Move the cursor to the mode

you want to call and press OPEN to confirm and back.

The saved mode could be called by the shortcut preset: Night Mode1—call 101 preset, Night

2---- call 102 preset.

Zoom Speed

At the submenu of Exposal, move the cursor to Zoom Speed, press OPEN, the cursor will

change to , then the parameter can be changed. Press OPEN to confirm and back or CLOSE

cancel and back.

Focus Speed

Move the cursor to Focus Speed, press OPEN, the cursor will change to , then the parameter

can be changed. Press OPEN to confirm and back or CLOSE cancel and back.

10/16

Open Menu

095

Auto Flip

033

Reference

034

Left Limit

092

Right Limit

093

Preset scan 1

081

Preset scan 2

082

Preset scan 3

083

Preset scan 4

084

Auto Scan

099

Camera ►

Pan ►

Shortcut Key

Self act

Nothing

Leisure Time

030

Home place

Off

AS speed

060

PS1 Speed

120

PS1 time

005

PS2 Speed

120

PS2 time

005

PS3 Speed

120

PS3 time

005

PS4 Speed

120

PS4 time

Auto Flip

Pan This operation can control the home place of the dome,

adjust the auto panning speed and 4 cruise line with

presets, also the auto flip function.

Home Place OFF (001-032, OFF)

AS Speed 060(000-080) Auto Pan speed

PS1 Speed 120(100-120) Presets cruise 1 speed

PS1 Time 005(5-120) ) Presets cruise 1 stop time.

PS2 Speed 120 Presets cruise 2 speed

PS2Time 005 Presets cruise 2 stop time.

PS3 Speed 120 Presets cruise 3 speed

PS3 Time 005 Presets cruise 3 stop time.

PS4 Speed 120 Presets cruise 4 speed

PS4 Time 005 Presets cruise 4 stop time.

Auto Flip On(On/Off)

Shortcut Key

The functions can be setting by presets number, and can be called by the preset number which

be set. Note: The right side number is the default short cut key,

they are the number of presets. The number can be saved by new shortcut but the old one will not

be cancel.

Example: Change the number 095 into 16 that after Open Menu, the Menu can be called by 16

preset, and also can be called by 95 preset.

In the presets, the preset scan line 1 will cruise from

presets 1-8, and preset scan line 2 will cruise from

presets 9-16, the preset scan line 3 will cruise from

presets 17-24, and the preset scan line 4 will cruise from

25-32. Every line will back the first preset when it met

the point never be set, and it will quit cruise if the first

preset is not be set. The function Auto Scan is right and

left limit scan.

Note: The changing of the shortcut key can not be

identical with the shortcut key already have.

Operation: Move the cursor to the item which going to be changed, press OPEN, then change the

parameter, press OPEN to confirm and back or CLOSE cancel and back.

Self Act.

The dome will check itself when electric and it will act

the program automatic.

Nothing

P Scan 1 Preset scan 1

P Scan 2 Preset scan 2

P Scan 3 Preset scan 3

P Scan 4 Preset scan 4

Indice

Altri manuali XtendLan Telecamera di sicurezza

XtendLan

XtendLan OUTIRDVS620FR-42 Manuale utente

XtendLan

XtendLan SDOMEOIR6-CM10 Manuale utente

XtendLan

XtendLan XL-ICA-107M1C Manuale utente

XtendLan

XtendLan SDOMEOAT2-SD310 Manuale utente

XtendLan

XtendLan XL-ICA-206M2T-M39 Manuale utente

XtendLan

XtendLan XL-ICA-106M3 Manuale utente

XtendLan

XtendLan HDC-SDOMEO51MIR-B Manuale utente

XtendLan

XtendLan XL-ICA-306M1 Manuale utente

XtendLan

XtendLan XL-ICA301A Manuale utente

XtendLan

XtendLan XL-ICA-306M3 Manuale utente

XtendLan

XtendLan XL-ICA-H660-SC110 Manuale utente

XtendLan

XtendLan XL-ICA-371M2 Manuale utente

XtendLan

XtendLan XL-ICA-206M2IR-36 Manuale utente

XtendLan

XtendLan SDOMEOAT-57030SD Manuale di istruzioni

XtendLan

XtendLan SDOMEO4802701 Manuale utente

XtendLan

XtendLan ABOX56022 Manuale utente

XtendLan

XtendLan Speed Dome Manuale utente

XtendLan

XtendLan XL-ICA-361M3CP Manuale utente

XtendLan

XtendLan PEDOMEOIR48023SD Manuale utente

XtendLan

XtendLan XL-ICA-661M1CP Manuale utente

XtendLan

XtendLan XL-ICA-206M1IR Manuale utente

XtendLan

XtendLan XL-ICA-641M2 Manuale utente

XtendLan

XtendLan XL-ICA-H660-SC110 Manuale utente

XtendLan

XtendLan XL-ICA562M1CIR Manuale utente

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente