Xterra TRX4500 Manuale utente
TRX4500 TREADMILL
1
TABLE OF CONTENTS
ImportantSafetyInstructions 2
ImportantElectricalInformation 3
ImportantOperationInstructions 4
AssemblyPackChecklist 5
Assemblyinstructions 6
FoldingInstructions 9
Operation of Your Treadmill 10
General Maintenance 17
Exploded View Diagram
21
Parts List
22
GT90D-NT024CEGS_1804A(XL)
2
WARNING- Read all instructions before using this appliance.
DANGER- To reduce the risk of electric shock disconnect your treadmill from the
electrical outlet prior to cleaning and/or service work.
WARNING- To reduce the risk of burns, fire, electric shock, or injury to persons,
install the treadmill on a flat level surface with access to a 220-volt AC, 10-amp grounded
outlet.
DO NOT USE AN EXTENSION CORD UNLESS IT IS 14AWG OR BETTER, WITH
ONLY ONE OUTLET ON THE END. The treadmill should be the only appliance in the
electrical circuit. DO NOT ATTEMPT TO DISABLE THE GROUNDED PLUG BY USING
IMPROPER ADAPTERS, OR IN ANY WAY MODIFY THE CORD SET. A serious shock or
fire hazard may result along with computer malfunctions.
■Do not operate treadmill on deeply padded, plush or shag carpet. Damage to both carpet
and treadmill may result.
■Do not block the rear of the treadmill. Provide a minimum of 3 1/2 feet clearance
between the rear of the treadmill and any fixed object.
■Keep children away from the treadmill. There are obvious pinch points and other caution
areas that can cause harm.
■Keep hands away from all moving parts.
■Never operate the treadmill if it has a damaged cord or plug. If the treadmill is not working
properly, call your dealer.
■Keep the cord away from heated surfaces.
■Do not operate where aerosol spray products are being used or where oxygen is being
administered. Sparks from the motor may ignite a highly gaseous environment.
■Never drop or insert any object into any openings.
■Do not use outdoors.
■To disconnect, turn all controls to the off position, remove tether cord, then remove
the plug from the outlet.
■Do not attempt to use your treadmill for any purpose other than for the purpose it is
intended.
■The pulse sensors are not medical devices. Various factors, including the user’s
movement, may affect the accuracy of heart rate readings. The pulse sensors are
intended only as exercise aids in determining heart rate trends in general.
■Use handrails provided; they are for your safety.
■Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for use
on your treadmill. Quality athletic shoes are recommended to avoid leg fatigue.
Remove tether cord after use to prevent unauthorized treadmill operation.
SAVE THESE INSTRUCTIONS - THINK SAFETY!
Important Safety Instructions
3
WARNING!
NEVER use a ground fault circuit interrupt (GFCI) wall outlet with this treadmill. As with any
appliance with a large motor, the GFCI will trip often. Route the power cord away from any
moving part of the treadmill including the elevation mechanism and transport wheels.
NEVER remove any cover without first disconnecting AC power. If voltage varies by ten percent (10%)
or more, the performance of your treadmill may be affected. Such conditions are not covered
under your warranty. If you suspect the voltage is low, contact your local power company or a
licensed electrician for proper testing.
NEVER expose this treadmill to rain or moisture. This product is NOT designed for use outdoors,
near a pool or spa, or in any other high humidity environment. The temperature specification is 40
degrees c, and humidity is 95%, non-condensing (no water drops forming on surfaces).
Circuit breakers: Some circuit breakers used in homes are not rated for high inrush currents that
can occur when a treadmill is first turned on or even during normal use. If your treadmill is tripping the
house circuit breaker (even though it is the proper current rating) but the circuit breaker on the
treadmill itself does not trip, you will need to replace the home breaker with a high inrush type. This is
not a warranty defect. This is a condition we as a manufacture have no ability to control. This part is
available through most electrical supply stores. Examples: Grainger part # 1D237, or available online
at www.squared.com part # QO120HM.
This product must be grounded. If the treadmill’s electrical system should malfunction or
breakdown grounding provides a path of least resistance for electric current, reducing the risk of
electric shock. This product is equipped with a cord having an equipment-grounding plug. The plug
must be plugged into an appropriate outlet that is properly installed and grounded in accordance
with all local codes and ordinances.
DANGER - Improper connection of the equipment-grounding conductor can result in
a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt
as to whether the product is properly grounded. Do not modify the plug provided with the
product if it will not fit the outlet; have a proper outlet installed by a qualified electrician.
This product is for use on a nominal 220-volt circuit, and has a grounding plug that looks like the
plug illustrated below. A temporary adapter that looks like the adapter illustrated below may be
used to connect this plug to a 2-pole receptacle as shown below if a properly grounded outlet is
not available. The temporary adapter should be used only until a properly grounded outlet, (shown
below) can be installed by a qualified electrician. The green colored rigid ear-lug, or the like,
extending from the adapter, must be connected to a permanent ground such as a properly
grounded outlet box cover. Whenever the adapter is used, it must be held in place by a metal
screw.
Grounded Outlet
Grounding Pin Grounded Outlet
Metal Screw
Adapter
Tab of
Grounding
Screw
Grounding Instructions
Important Electrical Information
4
●NEVER operate this treadmill without reading and completely understanding the results of
any operational change you request from the computer.
●Understand that changes in speed and incline do not occur immediately. Set your desired
speed on the computer console and release the adjustment key. The computer will obey
the command gradually.
●NEVER use your treadmill during an electrical storm. Surges may occur in your
household power supply that could damage treadmill components.
●Use caution while participating in other activities while walking on your treadmill; such as
watching television, reading, etc. These distractions may cause you to lose balance or
stray from walking in the center of the belt; which may result in serious injury.
●NEVER mount or dismount the treadmill while the belt is moving. Treadmills start with at a
very low speed and it is unnecessary to straddle the belt during start up. Simply standing on
the belt during slow acceleration is proper after you have learned to operate the unit.
Always hold on to a handrail or hand bar while making control changes (incline, speed,
etc.).
Do not use excessive pressure on console control keys. They are precision set to function
properly with little finger pressure. Pushing harder is not going to make the unit go faster
or slower. If you feel the buttons are not functioning properly with normal pressure
contact your dealer.
A safety tether cord is provided with this unit. It is a simple magnetic design that should be
used at all times. It is for your safety should you fall or move too far back on the tread-belt.
Pulling this safety tether cord will stop tread-belt movement.
To Use:
1. Place the magnet into position on the console control head. Your treadmill will not start
and operate without this.
2. Fasten the plastic clip onto your clothing securely to assure good holding power. Note:
The magnet has strong enough power to minimize accidental, unexpected stopping. The clip
should be attached securely to make certain it does not come off. Be familiar with its function
and limitations. The treadmill will stop, depending on speed, with a one to two step coast
anytime the magnet is pulled off the console. Use the red Stop / Pause switch in normal
operation.
Safety Tether Cord
Important Operation Instructions
5
ASSEMBLY PACK CHECKLIST
# 102. Combination M5 Allen Wrench &
Phillips Head Screw Driver (1pc)
# 103. M6 (66 × 86)
L Allen Wrench (1pc)
# 125. 5/16" ×3/4"
Button Head Socket Bolt (8pcs)
# 80. Ø8 × 1.5T
Split Washer (4pcs)
# 100.Ø5/16" × Ø18 × 1.5T
Flat Washer (8pcs)
# 44. Square Safety Key (1pc)
# 104. Lubricant (1pc)
# 99. 5/16" ×1/2"
Hex Head Bolt (8pcs)
# 90. 13L_Wrench (1pc)
# 126. M5 ×15L
Phillips Head Screw (6pcs)
# 74. 3.5 × 12m/m
Sheet Metal Screw (4pcs)
6
ASSEMBLY INSTRUCTIONS
STEP 1
Take out the treadmill from the carton and lay it aside on the smooth ground.
STEP 2
Connect Computer Cable (Middle) (54) with Computer Cable (Lower) (55) then insert
Right and Left Uprights (4) and (5) into the Frame Base (2) and use 13m/m Wrench (90)
to tighten 8 pcs of 5/16" × 1/2" Hex Head Bolts (99) and 8pcs of Ø5/16" × Ø18 × 1.5T
Flat Washers (100).
99
55
99
99
100
100
99
99
100
100
100
100
100
99
99
99
54
90
4
5
2
7
STEP 3
1. Connect the Computer Cable (Middle) (54) and Computer Cable (Upper) (53).
2. Connect the Speed Adjustment Switch W/Cable (Upper) (114) and Speed/Hand Pulse
Complex (28).
3. Connect the Incline Adjustment Switch W/Cable (Upper) (115) and Incline/Hand Pulse
Complex (29).
4. Insert Console Assembly (21) into right and left Uprights (4) and (5) and secure with 4
pcs of 5/16" × 3/4" Button Head Socket Bolts (125) with 4 pcs of Ø8 × 1.5T(80) Split
Washers by using Combination M5 Allen Wrench & Phillips Head Screw Driver (102).
54
53
4
5
21
125
80 125
80
114
115 29
28
STEP 4
Install Handrail Support (9) between left and right Uprights (5) and (4) and use
Combination M5 Allen Wrench & Phillips Head Screw Driver (102) to tighten 4 pcs of
5/16" × 3/4" Button Head Socket Bolts (125).
102
125
99
125
102
8
STEP 5
Install the Front Inner Handlebar Cover (L,R)) (107,110) and Right and Left Uprights with
the 4pcs of 3.5 × 12m/m_Sheet Metal Screws (74) by by using Combination M5 Allen
Wrench & Phillips Head Screw Driver (102) and tighten them.
74
102
107
102
74
110
STEP 6
Use Combination M5 Allen Wrench & Phillips Head Screw Driver (102) to tighten 6 pcs
M5 × 15m/m Phillips Head Screws (126) to secure right and left Frame Base Covers (39 ,
38) on theFrame Base (2).
126
102
38 2
126
39
102
2
NOTE: Please Tighten All Screws After All Components Assembly Complete.
9
Folding Instructions
Do not attempt to move the unit unless it is in the folded and locked position. Be sure the power
cord is secured to avoid possible damage. Use both handrails to maneuver the unit to the
desired position.
■Unfolding The Treadmill:
Apply slight forward pressure* on the treadmill running deck with one hand. Pull down on the
unlocking lever and slowly lower the running deck to the floor. The deck will lower unassisted
when it reaches about waist high. (As shown Figure 1.2)
*At the rear roller area to relieve pressure on the locking system.
■Folding The Treadmill:
Make certain the treadmill is at minimum incline. Lift the treadmill running deck until it
is secured by the locking telescoping tube assembly in center back of base.
(As shown Figure 3.)
■Transport
The treadmill is equipped with four transport wheels which are engaged when the treadmill is
folded. After folding simply roll the treadmill away. (As shown Figure 4.)
Indice
Altri manuali Xterra Tapis roulant
Xterra
Xterra Trail Racer TR3.0 Manuale utente
Xterra
Xterra ET94 Manuale utente
Xterra
Xterra TR6.2 Manuale utente
Xterra
Xterra TRX5500 Manuale utente
Xterra
Xterra 1640855 Manuale utente
Xterra
Xterra iPOWER+ Manuale utente
Xterra
Xterra 1640755US Manuale utente
Xterra
Xterra TR250 Manuale utente
Xterra
Xterra TR150 Manuale utente
Xterra
Xterra TL200 Manuale utente
Xterra
Xterra TR6.5 Manuale utente
Xterra
Xterra Wave Deck T9 Manuale utente
Xterra
Xterra TR6.55 Manuale utente
Xterra
Xterra TRX3500 Manuale utente
Xterra
Xterra 1640255 Manuale utente
Xterra
Xterra TRX2500 Manuale utente
Xterra
Xterra TR6.65 Manuale utente
Xterra
Xterra 1644958US Manuale utente
Xterra
Xterra TR6.4 Manuale utente
Xterra
Xterra XT95-NT17 Manuale utente
