Xunison Hub M20-E Manuale utente
Hub M20-E
1. Product Introduction
1
Xunison Hub M20-E
The Xunison Hub M20-E is a dual-band Wi-Fi range extender with a
convenient wall-plug design and two external high-performance
omni-directional antennas. It provides over 100 Mbps Fast Ethernet con-
nectivity to devices such as laptops, gaming consoles, and smart speak-
ers via an Ethernet port. The extender is compatible with any wireless
router, gateway, or cable/ADSL modem that supports WiFi.
Plug and play configuration
No additional configurations are required once the Xunison Hub M20-E
is setup successfully.
One-click fast pairing
The Xunison Hub M20-E oers easy configuration for extending the cov-
erage of your existing WLAN network by simply pressing the WPS button
on both the Xunison Hub and the main router.
Xunison Hub M20-E
2
Stable Wi-Fi with two external 5dBi antennas
The Xunison Hub M20-E utilizes external dual-band high-performance
antennas with MIMO technology to ensure stable and reliable perfor-
mance.
Dual-band Wi-Fi
With support for dual-band Wi-Fi, the Xunison Hub M20-E can operate
on both the 2.4GHz and 5GHz frequency bands, providing enhanced
wireless performance, flexibility and speeds upto 1200 Mbps.
Xunison Hub M20-E
2. Product Installation
3
2.1 To install the Xunison Hub M20-E, follow the steps below:
1.Plug the Xunison Hub into an electrical outlet near your router and wait
for the device to power on. Note that the distance between your upper/-
main router and the device should be 2 meters.
2.Press the WPS button (2.4G/5G) on the upper/main router and then
press the corresponding WPS button on your Xunison Hub M20-E (i.e.,
2.4G/5G) according to the actual relay needs.
3.Wait for the 2.4G/5G LED to turn solid green, indicating a successful
installation.
4. Once the Xunison Hub M20-E is successfully set up, you can relocate
the device within the router's wireless signal coverage area. Allow about
one minute for the device to adjust and check the color of the 2.4G/5G
LED to ensure that the connection is stable.
Xunison Hub M20-E
4
2.2 To adjust the position of the range extender, follow the steps
below:
1. As the Xunison Hub M20-E has plug-and-play configuration, no addi-
tional configurations are required.
2. Ensure the device is installed at a suitable location. Refer to the follow-
ing LED indicators to determine if the device is at an optimal distance
from your router:
3. Once the Xunison Hub is installed in a suitable location, you can con-
nect your smartphone, laptop, and other devices to the hub. You can use
the same SSID as your upper/main router or choose a new SSID. The
Wi-Fi password is the same as your existing router.
Xunison Hub M20-E
5
Installation Tips:
• Install the extender in a location where there are no obstacles, such as
walls or large furniture, blocking the signal.
• To avoid band interference, the device should be placed at a certain
distance from home appliances operating in the 2.4 GHz band, such as
microwave ovens and Bluetooth devices
Xunison Hub M20-E
3. LED Indicators
6
LEDs
Color
Status
Power
Solid ON
Device ON
OFF
Device OFF
CPU
Flash every 2 sec
Device working
Flash quickly
After RST button is pressed for 5 seconds
Solid ON
The device remains solid ON for 2 mins after
p
ressing the WPS button.
2.4GHz/
5GHz
Green LED On
Signal quality on 2.4 GHz/5GHz is best.
Orange LED On
Signal quality on 2.4 GHz/5GHz is weak.
O
No connection
LAN
Blue LED On
Ethernet cable is connected to the LAN port.
Blue LED OFF
Network cable not connected.
Blue LED blinking
Data is being transmitted.
Xunison Hub M20-E
4. Ports and Interfaces
7
Xunison Hub M20-E
Xunison Hub M20-E
5. Safety Guidelines
8
Attention
Use original and certified cables.
Ensure the device does not come into contact with water during storage,
transportation, and operation.
Keep away from heat sources and ensure the device has adequate ventilation.
Do not use any corrosive cleaner/oil to clean the device.
Keep out of the reach of children.
Tips
Please check the cable connections once the device is installed.
Place the Xunison Hub M20-E in an appropriate place for seamless internet
connectivity.
Restart the device in case of any internet connectivity problems.
Change your Wi-Fi passwords often.
Caution
In case of a malfunction or damage, the user should not disassemble. Change
the connections instead and contact technical support for assistance.
9
6. RF Parameters
For additional information
Please visit xunison.com/support to find answers to your support questions and
access the latest downloads and product services. You can also submit a ticket
for any issues you may face with our product. features and functionality."
Xunison Hub M20-E
Function Frequency Range Transmit Power
(EIRP)
2.4 GHz Wi-Fi
5 GHz Wi-Fi
2412 ~ 2472 MHz
5150 ~ 5850 MHz
Max 20dBm
Max 23dBm
Indice
