Yard force LS G30A Manuale utente
READ & UNDERSTAND
INSTRUCTION MANUAL
Save all warnings and instructions for future reference.
40V CORDLESS CHAIN SAW
Original Instructions
LS G30A & LS G30W
Hotline: 1300 418 640
Monday/Friday: 9.00am to 4.30pm
Saturday: 9.00am to 3.00pm
Email: [email protected]
Description of Product Parts 01
Technical Specications 03
Intended Use 03
Safety Information 04
Assembly 18
Adjustment 20
Knowledge of kickback 22
Operation 25
Storing and Maintenance 34
Troubleshooting 35
Warranty Conditions 36
LS G30A & LS G30W Original Instruction
CONTENT
1
Fig 1
Fig 2
Fig 3 Fig 4
1
4
5
10
11 12
25 8
9
7
6
16
17
2
3
24
21
20
23
22
18
19
13
14
15
DESCRIPTION OF PRODUCT PARTS
2
WARNING! If any parts are damaged or missing, do not operate this tool until the
missing parts are replaced. Failure to heed this warning could result in serious
personal injury.
NOTE! Always recycle the packaging in accordance with local recycling schemes.
Parts List
As shown in Fig 1-4
1. Rear handle
2. Lock-off button
3. On/off trigger switch
4. Oil tank cap
5. Oil tank watching window
6. Front handle
7. Hand guard (chain brake actuating lever)
8. Chain blade
9. Saw rail
10. SDS tension knob
11. Clutch cover
12. Clamp knob
13. Tension pin
Check the delivery parts (Fig 5)
Battery pack and charger are sold separately.
Carefully remove the machine from its packaging and check as the following parts are
complete:
14. Locking pin
15. Sprocket
16. Battery pack (sold with AL GC2A only)
17. Battery pack release button
18. Power indicator button
19. Power indicator
20. Charger (sold with AL G40A only)
21. Green /Red led
22. Electric contacts
23. Plug
24. Gripping teeth
25. Catcher
Fig 5
E
C
B
D
G
F
A
A. Motor head
B. Saw rail
C. Saw blade
D. Blade cover
E. Charger (sold with AL G40A
only)
F. Battery pack (sold with AL
GC2A only)
G. Manual
DESCRIPTION OF PRODUCT PARTS
3
Model LS G30A&LS G30W
Nominal voltage of product with battery 40 V d.c.
No load chain speed 11.3 m/s
Bar Length 300mm (12”) Oregen 124MLEA041
Chain Oregen 90PX045X (chain pitch 0.375”)
Guaranteed sound power level 98 dB(A)
Net weight 5.5 kg
Vibrations ah: 3.5 m/s² K=1.5 m/s²
Battery pack Model AL G40A
Battery capacity 4.0Ah
Battery charging time Max. 2.0hr
Battery charger Model AL GC2A
Input 220-240V AC,
50/60Hz 100W
Output 40V d.c. 2A
Protection class II
* The following information :
-That declared vibration total value has been measured in accordance with a standard test
method and may be used for comparing one tool with another.
-That declared vibration total value may also be used in a preliminary assessment of expo-
sure.
WARNING :
Depending on the actual use of the product the vibration values can differ from the declared
total!
Adopt proper measures to protect yourself against vibration exposure! Take the whole work
process including times the product is running under no load or switched off into consideration!
This Chain saw has been designed for cutting Tree or Log.
The machine is to be used only for its prescribed purpose . any other use is deemed to be a
case of misuse. The user/operator and not the manuafacturer will be liable for any damage or
injuries of any kind caused as a result of this.
Please note that our equipment has not been designed for use in commercial , trade or indus-
trial applications . our warranty will be voided if the machine is used in commercial , trade or
industrial businesses or for equivalent purposes.
TECHNICAL SPECIFICATIONS
INTENDED USE
4
IMPORTANT
Please read these instructions fully before assembling and
operating.
Description of symbols
Symbols are used in this manual to attract your attention to possible risks. The safety sym-
bols and the explications which accompany them must be perfectly understood. The warning
themselves do not prevent the risks and cannot be a substitute for proper methods of avoiding
accidents.
Warning symbols on the machine
Read the instructions for use before use
This symbol, before a safety comment, indicates a precaution, a
warning or a danger. Ignoring this warning can lead to an accident
for yourself or for others. To limit the risk of injury, re, or electrocu-
tion always apply the recommendations indicated.
Wear ear protection. Eye protection and gloves when using the
product.
Do not expose and operate the tool in rain.
Wear suitably sturdy shoes when operation the device.
Both of the operator’s hands must be used to operate the chain
saw.
Wear close-tting work clothes when operating the device.
Contact of the guide bar tip with any object must be avoided.
WARNING! Kickback may occur when the nose or tip of the guide
bar touches an object, and cause a lightning fast reverse reaction,
kicking the guide bar up and towards the operator, may cause seri-
ous personal injury.
Never operate a chain saw holding it with one hand only.
SAFETY INFORMATION
5
Bar length 300 mm, Maximum cutting length 240mm
Australian Regulatory Compliance Mark.
Waste electrical products should not be disposed of with house-
hold waste. Please recycle where facilities exist. Check your Local
Authority or retailer for recycling advice.
Warning Symbols on the charger
Warning!
Before any use, refer to the corresponding paragraph in the pres-
ent manual.
The charger is for indoor use only.
Double insulation.
Australian Regulatory Compliance Mark.
Warning Symbols on the battery pack
Batteries contain Li-ion, waste batteries should be sorted for eco-
friendly. Do not dispose of waste batteries as unsorted municipal
waste.
Do not throw into water.
Do not litter to re.
Do not subject the battery to strong sunlight over long periods and
do not leave it on a heater(max.45oC).
Take batteries to an old battery collection point where they will be
recycled in an environ-mentally friendly manner.
Waste electrical products should not be disposed of with house-
hold waste. Please recycle where facilities exist. Check your Local
Authority or retailer for recycling advice.
Australian Regulatory Compliance Mark.
SAFETY INFORMATION
6
GENERAL POWER TOOL SAFETY WARNINGS
WARNING! Read all safety warnings and all instruc-
tions. Failure to follow the warnings and instructions
may result in electric shock,re and/or serious injury.
Save all warnings and instructions for future refer-
ence. The term “power tool” in the warnings refers to
your mains-operated (corded) power tool or battery-
operated (cordless) power tool.
Work area safety
1. Keep work area clean and well lit.Cluttered or dark
areas invite accidents.
2. Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable liq-
uids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
3. Keep children and bystanders away while operat-
ing a power tool. Distractions can cause you to lose
control.
Electrical safety
1. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodied plug sand matching outlets will
reduce risk of electric shock.
2. Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
3. Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
SAFETY INFORMATION
7
risk of electric shock.
4. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords in-
crease the risk of electric shock.
5. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of elec-
tric shock.
6. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk
of electric shock
NOTE: The term “residual current device(RCD)” may
be replaced by the term “ground fault circuit interrupt-
er (GFCI)” or “earth leakage circuit breaker(ELCB)”
Personal safety
1. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the inuence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
2. Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
3. Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
SAFETY INFORMATION
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Yard force Motosega
