YASKAWA PS M07 Manuale utente
PS | M07-2BA00 | Manual
HB400 | PS | M07-2BA00 | en | 20-02
VIPA System MICRO
Power supply - PS M07
M07-2BA00_000_PS M07,1,EN - © 2020
YASKAWA Europe GmbH
Ohmstraße 4
91074 Herzogenaurach
Tel.: +49 9132 744 0
Fax: +49 9132 744 186
Email: [email protected]
Internet: www.yaskawa.eu.com
Table of contents
1 General.................................................................................................................... 4
1.1 Copyright © YASKAWA Europe GmbH............................................................ 4
1.2 About this manual............................................................................................. 6
1.3 Safety instructions............................................................................................ 7
2 Basics and mounting............................................................................................. 8
2.1 Safety information for users.............................................................................. 8
2.2 System conception........................................................................................... 9
2.3 Dimensions..................................................................................................... 10
2.4 Mounting......................................................................................................... 12
2.4.1 Mounting without mounting rail.................................................................... 13
2.4.2 Mounting with mounting rail......................................................................... 13
2.5 Wiring............................................................................................................. 15
2.5.1 Wiring power supply.................................................................................... 15
2.6 Demounting.................................................................................................... 16
2.7 Installation guidelines..................................................................................... 19
2.8 General data................................................................................................... 21
3 Power supply........................................................................................................ 23
3.1 Safety instructions.......................................................................................... 23
3.2 PS M07 DC24V, 1.5A_AC120V-240V............................................................ 24
3.3 Technical data................................................................................................. 27
Appendix............................................................................................................... 29
A History of changes............................................................................................ 31
VIPA System MICRO Table of contents
HB400 | PS | M07-2BA00 | en | 20-02 3
1 General
1.1 Copyright © YASKAWA Europe GmbH
This document contains proprietary information of YASKAWA and is not to be disclosed
or used except in accordance with applicable agreements.
This material is protected by copyright laws. It may not be reproduced, distributed, or
altered in any fashion by any entity (either internal or external to YASKAWA) except in
accordance with applicable agreements, contracts or licensing, without the express
written consent of YASKAWA and the business management owner of the material.
For permission to reproduce or distribute, please contact: YASKAWA Europe GmbH,
European Headquarters, Hauptstraße 185, 65760 Eschborn, Germany
Tel.: +49 6196 569 300
Fax.: +49 6196 569 398
Email: [email protected]
Internet: www.yaskawa.eu.com
Every effort has been made to ensure that the information contained in
this document was complete and accurate at the time of publishing. Nev-
ertheless, the authors retain the right to modify the information.
This customer document describes all the hardware units and functions
known at the present time. Descriptions may be included for units which
are not present at the customer site. The exact scope of delivery is
described in the respective purchase contract.
Hereby, YASKAWA Europe GmbH declares that the products and systems are in compli-
ance with the essential requirements and other relevant provisions. Conformity is indi-
cated by the CE marking affixed to the product.
For more information regarding CE marking and Declaration of Conformity (DoC), please
contact your local representative of YASKAWA Europe GmbH.
VIPA, SLIO, System 100V, System 200V, System 300V, System 300S, System 400V,
System 500S and Commander Compact are registered trademarks of YASKAWA Europe
GmbH.
SPEED7 is a registered trademark of YASKAWA Europe GmbH.
SIMATIC, STEP, SINEC, TIA Portal, S7-300, S7-400 and S7-1500 are registered trade-
marks of Siemens AG.
Microsoft and Windows are registered trademarks of Microsoft Inc., USA.
Portable Document Format (PDF) and Postscript are registered trademarks of Adobe
Systems, Inc.
All other trademarks, logos and service or product marks specified herein are owned by
their respective companies.
All Rights Reserved
EC conformity declaration
Conformity Information
Trademarks
VIPA System MICRO
General
Copyright © YASKAWA Europe GmbH
HB400 | PS | M07-2BA00 | en | 20-02 4
Contact your local representative of YASKAWA Europe GmbH if you have errors or ques-
tions regarding the content of this document. If such a location is not available, you can
reach YASKAWA Europe GmbH via the following contact:
YASKAWA Europe GmbH, Ohmstraße 4, 91074 Herzogenaurach, Germany
Fax: +49 9132 744 29 1204
Email: [email protected]
Contact your local representative of YASKAWA Europe GmbH if you encounter problems
or have questions regarding the product. If such a location is not available, you can reach
the YASKAWA customer service via the following contact:
YASKAWA Europe GmbH,
European Headquarters, Hauptstraße 185, 65760 Eschborn, Germany
Tel.: +49 6196 569 500 (hotline)
Email: [email protected]
Document support
Technical support
VIPA System MICRO General
Copyright © YASKAWA Europe GmbH
HB400 | PS | M07-2BA00 | en | 20-02 5
1.2 About this manual
The manual describes the power supply (PS) that can be used in the VIPA System
MICRO. Described are construction, application and technical data.
Product Order no. as of HW state:
PS M07 DC24V, 1.5A_AC120V-240V M07-2BA00 01
The manual is targeted at users who have a background in automation technology.
The manual consists of chapters. Every chapter provides a self-contained description of a
specific topic.
The following guides are available in the manual:
nAn overall table of contents at the beginning of the manual
nReferences with page numbers
The manual is available in:
nprinted form, on paper
nin electronic form as PDF-file (Adobe Acrobat Reader)
Important passages in the text are highlighted by following icons and headings:
DANGER!
Immediate or likely danger. Personal injury is possible.
CAUTION!
Damages to property is likely if these warnings are not heeded.
Supplementary information and useful tips.
Objective and contents
Target audience
Structure of the manual
Guide to the document
Availability
Icons Headings
VIPA System MICRO
General
About this manual
HB400 | PS | M07-2BA00 | en | 20-02 6
1.3 Safety instructions
DANGER!
There is a warning symbol on the housing of the power supply. This indi-
cates that all safety instructions listed in this manual must be observed
before commissioning!
DANGER!
Failure to comply with the specification may affect the protective functions
of the system!
The power supply is constructed and produced for:
nthe DC 24V supply of components.
noperation within the environmental conditions specified in the technical data
nthe installation on a 35mm mounting rail in a control cabinet, which provides protec-
tion against fire, environmental influences and mechanical impact
nindustrial applications
DANGER!
This device is not certified for applications in
– in explosive environments (EX-zone)
The manual must be available to all personnel in the
nproject design department
ninstallation department
ncommissioning
noperation
CAUTION!
The following conditions must be met before using or commis-
sioning the components described in this manual:
– Hardware modifications should only be carried out when the system
has been disconnected from power!
– Installation and hardware modifications only by properly trained per-
sonnel.
– The national rules and regulations of the respective country must be
satisfied (installation, safety, EMC ...)
National rules and regulations apply to the disposal of the unit!
Warning symbol on the
housing
Intended use
Documentation
Disposal
VIPA System MICRO General
Safety instructions
HB400 | PS | M07-2BA00 | en | 20-02 7
2 Basics and mounting
2.1 Safety information for users
VIPA modules make use of highly integrated components in MOS-Technology. These
components are extremely sensitive to over-voltages that can occur during electrostatic
discharges. The following symbol is attached to modules that can be destroyed by elec-
trostatic discharges.
The Symbol is located on the module, the module rack or on packing material and it indi-
cates the presence of electrostatic sensitive equipment. It is possible that electrostatic
sensitive equipment is destroyed by energies and voltages that are far less than the
human threshold of perception. These voltages can occur where persons do not dis-
charge themselves before handling electrostatic sensitive modules and they can damage
components thereby, causing the module to become inoperable or unusable. Modules
that have been damaged by electrostatic discharges can fail after a temperature change,
mechanical shock or changes in the electrical load. Only the consequent implementation
of protection devices and meticulous attention to the applicable rules and regulations for
handling the respective equipment can prevent failures of electrostatic sensitive modules.
Modules must be shipped in the original packing material.
When you are conducting measurements on electrostatic sensitive modules you should
take the following precautions:
nFloating instruments must be discharged before use.
nInstruments must be grounded.
Modifying electrostatic sensitive modules you should only use soldering irons with
grounded tips.
CAUTION!
Personnel and instruments should be grounded when working on electro-
static sensitive modules.
Handling of electrostatic
sensitive modules
Shipping of modules
Measurements and altera-
tions on electrostatic sen-
sitive modules
VIPA System MICRO
Basics and mounting
Safety information for users
HB400 | PS | M07-2BA00 | en | 20-02 8
2.2 System conception
The System MICRO is a modular automation system for assembly on a 35mm mounting
rail. By means of periphery modules this system may be adapted matching to your auto-
mation tasks. In addition, it is possible to expand your CPU by appropriate interfaces. The
wiring complexity is low, because the DC 24V electronic section supply is integrated to
the backplane bus and this allows replacement with standing wire.
nCPU
nExtension module
nPeriphery module
With the CPU electronic, input/output components and power supply are integrated to
one casing. In addition, up to 8 periphery modules of the System MICRO can be con-
nected to the backplane bus. As head module via the integrated power module for power
supply CPU electronic and the I/O components are supplied as well as the electronic of
the periphery modules, which are connected via backplane bus. To connect the power
supply of the I/O components and for DC 24V electronic power supply of the periphery
modules, which are connected via backplane bus, the CPU has removable connectors.
By installing of up to 8 periphery modules at the backplane bus of the CPU, these are
electrically connected, this means these are assigned to the backplane bus and con-
nected to the DC 24V electronic power supply.
By using extension modules you can extend the interfaces of the CPU. The attachment to
the CPU is made by plugging on the left side of the CPU. You can only connect one
extension module to the CPU at a time.
Overview
Components
CPU
Extension module
VIPA System MICRO Basics and mounting
System conception
HB400 | PS | M07-2BA00 | en | 20-02 9
The power supply is mounted on the left side from the DIN rail with the System MICRO
modules. It serves for electronics and power supply.
By means of up to 8 periphery modules, you can extend the internal I/O areas. The
attachment to the CPU is made by plugging them on the right side of the CPU.
2.3 Dimensions
Dimensions in mm
Power supply
Periphery module
Dimensions CPU M13C
VIPA System MICRO
Basics and mounting
Dimensions
HB400 | PS | M07-2BA00 | en | 20-02 10
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali YASKAWA Alimentazione elettrica
YASKAWA
YASKAWA U1000 Series Manuale utente
YASKAWA
YASKAWA PS-A10LB Manuale utente
YASKAWA
YASKAWA PS 307-1BA00 Manuale utente
YASKAWA
YASKAWA JEPMC-PSD3012-E Manuale utente
YASKAWA
YASKAWA SGMJ Series Manuale utente
YASKAWA
YASKAWA PS-A10L Manuale utente
YASKAWA
YASKAWA VIPA System 300S Manuale utente
YASKAWA
YASKAWA PS-A10HB Manuale utente
