YASKAWA Smart Series Manuale utente
Part Number: 188791-1
Revision: 0
YASKAWA SMART SERIES
HC10DT COLLABORATIVE ROBOT
QUICK START GUIDE
WITH SMART PENDANT AND YRC1000micro
Upon delivery of the product and prior to operation, read all included instructions thoroughly, and
retain for future reference.
ii
188791-1
188791-1
Copyright
Smart Series HC10DT
Collaborative Robot
Copyright
Copyright © 2019, YASKAWA America, Inc.
Terms of Use and Copyright Notice
All rights reserved. This manual is freely available as a service to
YASKAWA customers to assist in the operation of the Motoman robots,
related equipment and software This manual is copyrighted property of
YASKAWA and may not be sold or redistributed in any way. You are
welcome to copy this document to your computer or mobile device for
easy access but you may not copy the PDF files to another website, blog,
cloud storage site or any other means of storing or distributing online
content.
Printed in the United States of America
First Printing, 2019
YASKAWA America, Inc.
Motoman Robotics Division
100 Automation Way
Miamisburg, OH 45342
Phone: 937-847-6200
www.motoman.com
Notes for Safe Operation
Read all included manuals carefully before installing, operating,
maintaining, or inspecting the system.
In this instruction, Safe Operations are classified as “DANGER”,
“WARNING”, “CAUTION” or “NOTICE”.
Registered Trademark
In this manual, names of companies, corporations, or products are
trademarks, registered trademarks, or bland names for each company or
corporation. The indications of ® and TM are omitted.
DANGER Indicates an imminently hazardous
situation which, if not avoided, WILL
result in death or serious injury.
WARNING Indicates a potentially hazardous
situation which, if not avoided, MAY
result in death or serious injury.
CAUTION Indicates a hazardous situation,
which if not avoided, MAY result in
minor to moderate injury.
CAUTION Indicate a situation which if not
avoided may result in equipment
damage.
NOTICE Indicates practices not related to
personal injury.
1-1
188791-1
188791-1
1 General Information
1.1 Introduction
Smart Series HC10DT
Collaborative Robot
1 General Information
1.1 Introduction
This is a YASKAWA Smart Series HC10DT Collaborative Robot Quick
Start Guide for Robots that have Smart Pendant Version 1.3.5 and newer.
This document is intended to guide the user through a basic installation
and setup of the Robot and the user to perform basic moves to confirm
setup was successful. A complete set of manuals is provided and are to
be reviewed by all working with or near the Robot.
1.2 Safety
Before installing and powering on the Robot, be sure to read and
understand all safety information. Refer to the safety sections of all
included manuals. All YASKAWA manuals are included on a USB.
1.3 Robot Assembly
Fig. 1-1: Robot Assembly Includes:
1.4 Training
YASKAWA recommends users complete the free online courses listed
below before proceeding to the next sections:
– HC10 w/wo DT YRC1000micro Controller w/ Smart Pendant
– Intro to Robotics
– Yaskawa Safety Principles
1.4.1 How to Access Free Online Training
1. Go to “YASKAWA Academy Catalog”
https://yaskawaacademy.myabsorb.com/#/catalog/
2. Press the {$0.00} located underneath each of the desired courses to
add them to the “Cart”
3. Review the items in the Cart and press {Proceed to Checkout}
4. Follow instructions to “Sign In” or “Sign Up”
• An activation link is sent to the email address on file, if signing up for
the first time
5. Enrolled courses can be found in “My Courses” on the dashboard, or
at https://yaskawaacademy.myabsorb.com/#/courses
6. Use {Start} to begin the course
Smart Pendant
Manipulator
YRC1000micro
USB
Ｒｏｂｏｔ Ｍａｎｕａｌ
READ ONLY MEMORY
Ｒ
ｂ
Ｍ
ｌ
Ｒｏｂｏｔ Ｍａｎｕａｌ
Ｒ
ｂ
ｔ
Ｍ
ｌ
Base I/O
Cable
25
13
14
1
1 2 3 4 5 6 7 8 9 10 11 12 13
XXXXXX
CN3
3
1 2 3 4 5 6 7 8 9 1011 12 13 14 15 16 17 18 2021 22 23 24
XXXXXX
2526
CN4
3
Terminal Blocks for Safety I/O (Left)
General Purpose I/O (Right)
CN3 Safety Cable
CN4 GPIO Cable
Switch/Lamp
Cable
Torque Sensor
Cable
Manipulator
Cable
2-1
188791-1
188791-1
2 Setup HC10DT Smart Series Robot
2.1 Transportation
Smart Series HC10DT
Collaborative Robot
2 Setup HC10DT Smart Series Robot
2.1 Transportation
.
2.1.1 Manipulator
2.1.1.1 Using Crane
Remove the plastic cover between the R and U axis to install the included
hardware to lift and transport.
Refer to Chapter 2 Transporting in the MOTOMAN-HC10DT
INSTRUCTIONS, for transportation instructions.
Fig. 2-1: Lift Connections with Crane
2.1.2 Controller
The Controller can be moved manually with a forklift or a platform truck.
Refer to Chapter 3 Installation in the YRC1000micro INSTRUCTIONS, for
detailed instructions for transporting.
CAUTION
• Use at least two people to transport and unpack the Manipulator
and Controller to the installation location
• Do not transport the Manipulator and Controller at the same time.
Not following these CAUTIONs can result in injury and/or equipment
damage.
Factory setting for angle and pulse of each axis
Axis
Angle
Pulse
S
0°
0
L
0°
0
U
0°
0
R
0°
0
B
0°
0
T
0°
0
indicates the position of
the center of gravity.
Hexagon socket head cap screw M8
(length: 25 mm)(2 screws)
Conical spring washer M8 (2 washers)
Tightening torque: 24.5 N•m (2.5 kgf•m)
(130)
(454)
(34)
(541)
(301)
HW1307411-1 (shipping bolts and brackets)
(265)
Casing cover
Screw (provided with the cover)
Tightening torque:
1.2 N•m (0.12 kgf•m)
(1125)
CAUTION
• Hold the Controller firmly from the bottom if moving manually.
Not holding the Controller firmly from the bottom can damage the
Controller.
2-2
188791-1
188791-1
2 Setup HC10DT Smart Series Robot
2.2 Manipulator Installation
Smart Series HC10DT
Collaborative Robot
2.2 Manipulator Installation
Attach the Manipulator base to the baseplate using four hexagon socket
head cap screws M12 (Tensile strength: 1200 N/mm2 or more,
recommended length: 45 mm) by tightening to 84 Nm. The hexagon
socket head cap screws and the anchor bolts must be tightened firmly so
they do not loosen over time.
Refer to section 3.2 Mounting Procedures for Manipulator Base in the
MOTOMAN-HC10DT INSTRUCTIONS.
Fig. 2-2: Installing Manipulator Base and Baseplate
Anchor bolt (M12 or larger)
Baseplate
67.5 ±0.1
195 ±0.1
67.5 ±0.1
97.5 ±0.197.5 ±0.1
195 ±0.1
(Reference hole)
Baseplate
8 dia. (2 holes)
+ 0.015
0
14 dia. hole for mounting (4 holes)
1632 or longer
Hexagon socket head cap
screw M12 (4 screws)
Conical spring washer
Washer
measurements in mm
2-3
188791-1
188791-1
2 Setup HC10DT Smart Series Robot
2.3 Controller Installation
Smart Series HC10DT
Collaborative Robot
2.3 Controller Installation
The Controller can be installed in a 19 inch server rack with compatible
hardware (not included).
Refer to chapter 3 Installation in the YRC1000micro INSTRUCTIONS for
detailed instructions on Controller installation.
Fig. 2-3: Controller Dimensions
CUSTOMER
SUPPORT
(Back View) (Front View)
(Top View)
425W x 188H x 405D
2-4
188791-1
188791-1
2 Setup HC10DT Smart Series Robot
2.4 Wiring Robot
Smart Series HC10DT
Collaborative Robot
2.4 Wiring Robot
2.4.1 Reference Material
Refer to the following manuals for detailed wiring instructions:
–READ FIRST!! YRC1000micro GPIO and Direct IN Connections
–Section 1.5.2 Connecting to the YRC1000micro of the YRC1000/
YRC1000micro INSTRUCTIONS FOR Smart Pendant
–Chapter 2 Connections of the YRC1000micro SUPPLEMENTARY
INSTRUCTIONS FOR HC10/HC10DT
–Chapter 4 Wiring of the MOTOMAN-HC10DT INSTRUCTIONS
2.4.2 Basic Wiring Overview
Fig. 2-4: Basic Wiring
2-5
188791-1
188791-1
2 Setup HC10DT Smart Series Robot
2.4 Wiring Robot
Smart Series HC10DT
Collaborative Robot
2.4.2.1 Controller Detailed Connectors
– The Pendant connects to the bottom section of the Controller as shown
in Fig. 2-4.
– General Purpose I/O (GPIO) connects to the top section of the
Controller and the Safety I/O connects to the bottom section of the
Controller (see Fig. 2-4). Refer to the READ FIRST!! YRC1000micro
GPIO and Direct IN Connections for more details.
Fig. 2-5: Controller Connections
2.4.2.2 Manipulator Detailed Connectors
– Uses four cables:
• 1BC - encoder and axis (Manipulator) cable.
• SW - switch/lamp (collaborative button power & signal) cable.
• TQ - torque sensor (Torque sensor power & data) cable.
• S - Base I/O (using I/O through the arm) cable. For more information,
refer to Fig. 2-7.
Fig. 2-6: Manipulator Connections
SW
1BC TQ
S
2-6
188791-1
188791-1
2 Setup HC10DT Smart Series Robot
2.4 Wiring Robot
Smart Series HC10DT
Collaborative Robot
Fig. 2-7: Base I/O Cable Assembly
WIRE SIDE SHOWN
2:1
18
19
20
1
2
14
11
12
13
3
4
10
17
16
15
56
9
8
7
XXXXXX
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16 16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
WHT22
RED22
ORN22
BLK22
BRN22
BLK22
YEL22
BLK22
BLU22
BLK22
GRN22
BLK22
WHT22
BLK22
RED22
BLK22
2-7
188791-1
188791-1
2 Setup HC10DT Smart Series Robot
2.5 Power ON
Smart Series HC10DT
Collaborative Robot
2.5 Power ON
The main power supply is turned ON when the Controller’s [POWER]
switch is flipped to the “ON” position. After a few seconds, the startup
screen appears on the Pendant.
Fig. 2-8: Controller Power Switch
Fig. 2-9: Pendant Startup Screen
If the Pendant does not complete the startup sequence due to an error
(e.g. Controller Software incompatibility), an {Export Logs} button
appears. Use the {Export Logs} button to save internal logs to a USB
storage device that is inserted in the Smart Pendant to aid with
troubleshooting by Customer Support.
WARNING
• Perform a risk assessment of the Robot and application before
powering ON the Robot.
Not performing a risk assessment before Powering ON the Robot may
result in death or serious injury.
Altri manuali per Smart Series
1
Questo manuale è adatto per i seguenti modelli
1
Altri manuali YASKAWA Robotica
YASKAWA
YASKAWA YYR-1-06VXH25-A10 Istruzioni operative
YASKAWA
YASKAWA Motoman DX200 Manuale utente
YASKAWA
YASKAWA MOTOMAN-MC2000 II Manuale utente
YASKAWA
YASKAWA Motoman ArcWorld IV-6300 XHD TR3C Guida utente
YASKAWA
YASKAWA MOTOMAN-HP20D Manuale utente
YASKAWA
YASKAWA MOTOMAN-VA1400 Manuale utente
YASKAWA
YASKAWA MOTOMAN-VS100 Manuale utente
YASKAWA
YASKAWA MOTOMAN DX100 Manuale utente
YASKAWA
YASKAWA MOTOMAN-MPX2600 Manuale utente
YASKAWA
YASKAWA MOTOMAN-MH50 Manuale utente
YASKAWA
YASKAWA MOTOMAN FS100 Manuale utente
YASKAWA
YASKAWA MOTOMAN-HP20 Manuale utente
YASKAWA
YASKAWA MPL500-J00 Istruzioni operative
YASKAWA
YASKAWA MH180 Istruzioni operative
YASKAWA
YASKAWA MOTOMAN DX100 Manuale utente
YASKAWA
YASKAWA MOTOMAN MYS450L Manuale
YASKAWA
YASKAWA MOTOMAN-MH600 Manuale utente
YASKAWA
YASKAWA MA1440 Istruzioni operative
YASKAWA
YASKAWA MOTOMAN MPL80 II Manuale utente
YASKAWA
YASKAWA MH50II Istruzioni operative
