YewdaleDefiant C20s Manuale utente

Fitting Instructions

for YewdaleDefiant® cassetted blinds

(C20s)

yewdale.co.uk

Fitting Instructions

YewdaleDefiant®cassetted blinds

(C20s)

Part no: 2000

YewdaleDefiant® fitting instructions Part no: 20002

Fitting Instructions

YewdaleDefiant®cassetted blinds (C20s)

Safety Instructions:

1.Loops in pull cords, chains, tapes and inner cords that operate the product

can cause strangulation

2. To avoid strangulation and entanglement, keep cords out of the reach of

young children. Cords may become wrapped around a child’s neck

3.Move beds, cots and furniture away from window covering cords

4. Do not tie cords together. Make sure cords do not twist and create a loop

N.B. For more information and child safety device ﬁtting instructions, see Point

13 on Page 5.

Call: +44 (0)1268 570900 Fax: +44 (0)1268 732509 Email: [email protected] Visit: www.yewdale.co.uk 3

Cassetted Blinds:

N.B. This blind should be installed by a person competent in DIY. If in doubt

please consult a professional.

1.Remove the two safety screws in the underside of the head box to enable the

cover to open (if sidewinder, also unscrew the chain guide).

2.Using the indents (see diagram below) within the head box, drill 3.8mm

ﬁxing holes either in the top or back depending on whether it is required to

be face or recess ﬁxed. Fixing holes should be equally spaced and no more

than 1m apart to ensure head box is ﬁxed completely level.

3.Lift the head box in to place. If you are ﬁtting it to steel or concrete, mark

where the holes need to be drilled so the hole can be plugged. Drill the

holes and lift the head box into place and ﬁx using the appropriate screws.

If ﬁtting it to timber, simply ﬁx the head box in place using the appropriate

screws.

NB. To operate correctly, complete blind MUST be level.

YewdaleDefiant® fitting instructions Part no: 20004

Fitting Instructions

YewdaleDefiant®cassetted blinds (C20s)

4.Insert the barrel and fabric into the head box. If it is spring controlled, go to

point 5 - 6 and then to point 11. If the blind is side winder controlled, go to

point 7- 9 and then to point 11. If the blind is crank controlled, go to point 9

and then to point 16. If it is electrically controlled, go to point 10 and refer to

motor instructions for setting limit stops.

5.Insert/click the blind on to the back bar into the head box. The spring must

be on the right-hand side unless fabric is reverse rolled.

6.The spring would have been tensioned during the manufacturing process

but the tension can be increased or decreased if required. If the fabric does

not wind up completely when the blind is operated, greater spring tension

can be applied as follows:

a) The spring would have been tensioned during the manufacturing process

but the tension can be increased or decreased if required. If the fabric

does not wind up completely when the blind is operated, greater spring

tension can be applied as follows:

b) Remove the blind and back bar from the head box.

c) Use a ﬂat head screwdriver through the hole in the bracket at the spring

end to either increase or decrease the tension as desired.

d) Insert/click the barrel and fabric back into the head box.

e) Attach the pull cord onto the bottom bar.

7.Fix the chain guide into position by threading the chain through the chain

guide. Ensure that the chain is not twisted.

8.Re attach the chain guide using the screws provided.

9.Insert the barrel and fabric into the head box.

10.Drill an exit hole for the electric cable and insert the fabric and barrel into

the head box, making sure the supply cable is carefully threaded through.

11.If side guiding is required, please follow the instructions overleaf. If not

required then click the cover back in place and secure using the 2 safety

screws previously removed.

12.Check the blind operates correctly.

Call: +44 (0)1268 570900 Fax: +44 (0)1268 732509 Email: [email protected] Visit: www.yewdale.co.uk 5

13.Ensure the relevant child safety device is used to comply with BS

EN13120:2009+A1:2014, BS EN16433:2014 and BS EN16434:2014 as

follows: *You will have been provided with either a chain tidy or easy

break chain connector (also see page 8 & 11)

Chain Tidy

The chain tidy will be attached to the chain

when the blind arrives. The chain tidy should

be at a maximum distance from the control

mechanism, keeping the chain taut (not

under excessive tension however as this

could negatively aect the longevity and

operation of the blind). Put the retaining

device on the wall, mark ﬁxing holes with a

pencil, drill the holes and screw the device

to the wall with suitable ﬁxings.

Easy Break Chain Connectors

Two easy break chain connectors are connected to the operating chain

200mm apart. This ensures that at least one of them will be in the vertical

position ensuring they perform as required. If excessive weight is applied

within the loop a connector will come apart. If a connector comes apart

and is undamaged then it will need to be re-connected by inserting the

last ball on the end of the chain into the hole in the connector and pushed

into place.

YewdaleDefiant® fitting instructions Part no: 20006

Fitting Instructions

YewdaleDefiant®cassetted blinds (C20s)

Side Guide Wires:

N.B. This blind should be installed by a person competent in DIY. If in doubt

please consult a professional.

1.Cutting two lengths of the steel wire, 918003S to length (Blind drop +

100mm), attach the 918011 guide wire clamp to one end of each of the

wires.

NB. By holding the 918011 with pliers, it is important that the screw in this

product is tightened ﬁrmly against the wire.

2.Thread the loose end of the wire through the transition plates from the top

(using the back hole provided).

3.Thread the steel wire through the guide holes in the bottom bar end caps,

938313W/B/S.

4.Unscrew both covers of the bezels.

5.Fix the bezels, 918008 directly below 918011W’s (if face ﬁx application us

the face ﬁx adaptor).

6.Thread the steel wire through the bezel cover (from the top).

7.Holding the covers in line with the home position, calculate the length of

the wire and trim to size.

8.Cut the wire to length and securely fasten 918011 wire clamps to the end of

the wire.

NB. By holding the 918011 with pliers, it is important that the screw in this

product is tightened ﬁrmly against the wire.

9.Screw the cover caps onto the bezels until the wire is taught.

10.For motor programming instructions, please refer to the enclosed leaﬂet.

NB. Ensure when the blind is travelling up or down, the cable/bottom bar are

not being pulled out of line.

11.If the blind is spring operated, attach the knot holder to the bottom bar

(along with pull cord and acorn). Attach the cleat to the cill to hold the blind

in the ‘Down’ position.

Call: +44 (0)1268 570900 Fax: +44 (0)1268 732509 Email: [email protected] Visit: www.yewdale.co.uk 7

Side Guide Wires:

918003S

Steel wire

918008

Bezel with face

ﬁx adaptor 9180011

Guidewire clamp

Diagram

Showing Wire

Connection

938311B/S/W

Tear drop

aluminium bottom bar

938312W/B/S End cap

+938313W/B/S Side

guiding adaptor

OPTIONAL

Side Guide

938314W

Lug

6200W

Aluminium

Channel

Yewdale, Enterprise Way,

Wickford, Essex SS11 8DH

Call +44 (0)1268 570900

Fax +44 (0)1268 732509

Email [email protected]

Visit yewdale.co.uk

For more information on all

Yewdale products, please call

the sales department.

Indice

Altri manuali YewdaleDefiant Tenda per finestra

YewdaleDefiant

YewdaleDefiant VL30 Single Draw R/H Control Manuale utente

YewdaleDefiant

YewdaleDefiant C40-60 Manuale utente

YewdaleDefiant

YewdaleDefiant F30 Manuale utente

YewdaleDefiant

YewdaleDefiant C40-90 Manuale utente

YewdaleDefiant

YewdaleDefiant C57-90T Manuale utente

YewdaleDefiant

YewdaleDefiant R20M Manuale utente

YewdaleDefiant

YewdaleDefiant C40-120T Manuale utente

YewdaleDefiant

YewdaleDefiant C40-120 Manuale utente

YewdaleDefiant

YewdaleDefiant C47-90 Manuale utente

YewdaleDefiant

YewdaleDefiant R20 Manuale utente

YewdaleDefiant

YewdaleDefiant VL31 Single Draw R/H Control Manuale utente

YewdaleDefiant

YewdaleDefiant R20 Manuale utente

YewdaleDefiant

YewdaleDefiant C40s Manuale utente

YewdaleDefiant

YewdaleDefiant C40-90T Manuale utente

YewdaleDefiant

YewdaleDefiant R42 Manuale utente

YewdaleDefiant

YewdaleDefiant C40-60T Manuale utente

YewdaleDefiant

YewdaleDefiant VL31 Split Draw Manuale utente

YewdaleDefiant

YewdaleDefiant R20B Manuale utente

YewdaleDefiant

YewdaleDefiant C20s Manuale utente

YewdaleDefiant

YewdaleDefiant C44-90 Manuale utente

YewdaleDefiant

YewdaleDefiant F30 Manuale utente

Manuali Tenda per finestra popolari di altre marche

Jysk

Jysk ROGEN Manuale utente

SOMFY

SOMFY 1241752 Manuale utente

Rollos

Rollos S-Nanorollo V2 Guida alla pianificazione

Teptron

Teptron Move Manuale utente

Renson

Renson Outdoor Loggia Guida di sicurezza

Project Source

Project Source CDLF2342W Manuale utente

Domondo

Domondo PureNight Manuale di istruzioni per l'installazione

rollease acmeda

rollease acmeda Easy Spring Air Guida all'installazione

IKEA

IKEA KADRILJ Manuale utente

Hallis Hudson

Hallis Hudson Rolls Super glide Manuale utente

Benthin

Benthin P1614 Manuale utente

MV LINE

MV LINE CLARA 015 Manuale di istruzioni

Current

Current E-WAND Guida

weinor

weinor VertiTex ZipR Manuale

Roto

Roto ZAR M R4/R7 Manuale utente

SOMFY

SOMFY Movelite WT Series Manuale utente

Acmeda

Acmeda RF400 Series Manuale utente

Motura

Motura Pli_353/3 Manuale utente