Yongnuo YN560 Manuale utente
I
.
Warning
To avoid fire or electrical shock, do not expose this product to rain or moisture.
Do not flash at high level output continuously for over 15 times.
To avoid short circuit, make sure the batteries are securely packed
so that the contacts
do not touch each other and take care not to short circuit the batteries
when handling
them.
Please place the batteries and any other small parts that
can be swallowed mistakenly
away from children. Contact a doctor immediately if this happens.
To avoid possible injury to eyes, do not use the flash light close to the eyes.
Do not use the flash light on the people who
have medical conditions that might be
aggravated by this without first consulting a doctor.
Please remove the batteries from the flash light and stop using immediately in case of:
●It is dropped or otherwise seriously damaged so that inner components are revealed.
●If the battery leaks corrosive liquids or chemicals
, please take out the battery with
gloves.
●The product gives off strange smell, smokes or becomes very hot.
Do not disassemble or maintain this product. Touching the internal high voltage circuits
will cause serious electrical shock.
II
. Features
YN560 is a new flash specially designed for professional creative photography.
Compared with YN460-II and YN460, it has the following new features:
New appearance: The new flash looks more stylish, impressive, easy to use
and
professional.
New power zoom function: Set by using buttons on the flash, giving the flash a
focal
length coverage ranging from 24 to 105mm.
GN58 @ ISO100, 105mm: YONGNUO has designed the YN560 with a higher
guide
number, to match the mainstream professional hot shoe flashes.
The improved wireless triggering sensor: YONGNUO improves the wireless
triggering sensor for YN560, with S1 and S2 modes that can also be used outdoors, with
a wireless triggering distance of up to 15m.
Sound signal: When the YN560 is fully charged, the flash will give a ready
sound, so
you may concentrate on the creati
ve process. (Note: the sound can be disabled).
New charging socket for external power pack: YN560 has the addition of
a
charging socket for an external power pack, to meet the need for a faster
charging
recycle.
New PC synchronous port: YN560 adds a standard screwlock
PC synchronous port,
which makes it
easier to use PC
synchronous cables
.
Super fast recharging cycle: It only takes as little as 3 seconds to recharge
after full
power flash. Even without new batteries, the recharge cycle should need
only needs 4~5
seconds; significantly reducing the inconvenience of having to wait
for charging. In
addition, you can use an external power pack to accelerate the recharging speed.
Supporting high-speed continuous shooting: With power settings of 1/8 or below, the
YN560 can support the 8FPS high-speed continuous shooting.
Improved power saving mode: YONGNUO has re-designed
the power saving mode
for YN560. In the power saving mode, the flash will automatically
shutdown sooner;
and the user can select a non-saving mode, where
it will take a long time before
automatic shutdown.
The more fine tuned output control: The output control of YN560 is more
accurate
selectable, ranging from 1/128 to 1/1 and each step has 8 smaller fine tuning steps
;
Coupled with the zoom flash head, YN560 gives you precise control to
achieve your
desired lighting effect.
Automatic setting saving: YN560 automatically saves your current setting
when
powered off.
III
.
Parts
(
Please read
this
section
carefully,
to
familiar
ize
yourself with the product)
1. Built-in bounce card
2. Built-in wide-fl ash adapter
3. Flash light’s head
4. External power pack socket
(It can be connected to
the SF-18C or SF-17C
external power pack)
5. Screwlock PC port (for input)
6. Port cover
7. Battery bay cover
8. Optical control sensor
9. Locking ring
10. Hot shoe stand
11. Hot shoe pin
12. Mode indicator (M, S1, and S2): Indicates the current flash mode.
13
.
Output
level
indicator
:
Set
the output power by button; there are 8
level
s for
output level adjustment. Indicates the output power and the fine-tuning; it also
indicates
the current focal length when adjusting the zoom.
14. The sound switch: A short press will enable or disable the ready sound; hold
down
the button for longer to turn on/off the power saving mode.
15. Mode switch button: Change the mode of the flash light
; it will cycle through
M/S1/S2 for each press.
16. Charging indicator / Test button: The red light will glow when the
charging
process is complete and the flash light can be used; it will glow green to show
that it is
charging or the batteries are low on power
; alternate flashing of red and green light
shows overheat protection cutout. If you press the test button (PILOT), the flash
will
give a test flash.
17. Power Save indicator: When power saving mode is disabled,
the indicator is lit for
a long period; when the power saving mode is enabled, the light is off. When the
flash
enters sleep mode, the indicator will flash.
18．Flash head manual motor zoom: You can adjust the zoom setting by pressing the
[＋] and [－] keys (24, 28, 35, 50, 70, 80, 105mm).
19
．
Power switch
:
Switch t
he flash light
on/off
by
holding
this button
down
for 2
seconds.
20．Power adjustment button: Adjust the power output major steps by
pressing the
[LEFT] [RIGHT] buttons of the main control, and make fine tune power changes by
pressing [UP] [DOWN] and then press [OK] in the middle to set fine tune setting.
I
V
. Installation Instruction
1. Install Batteries
Slide the battery bay cover in the direction of the arrows to open.
Insert the batteries, with polarity according to the label inside battery
bay. Make sure the battery polarity is correct.
Close the battery bay cover in the direction of the arrows.
2. Mount the flash light on your camera
Loosen the locking ring by turning it in the direction
of the arrow. Slip the flash light hot shoe stand into
the camera hot shoe stand until it stops. Turn the
locking ring in the direction of the arrow tighten. To
detach the flash light, loosen the locking ring by
turning it in the opposite direction.
V
. Basic Functions
1. Basic Operations
Operation of the buttons:
Component Operation
[Power Switch] Power switch for the flash light. The flash light
can be switched
on/off by pressing this button for 2 seconds.
It is recommended that the batteries be removed from the
battery bay only after the flash light is switched off using this
button.
[Mode Switch
Button] The trigger mode of the flash light can be cycled through
M/S1/S2 by pressing.
[Sound Switch] Pressing can enable or disable the ready sound signal. Holding
this button down for 2 seconds will enable or disable the
power
saving mode.
[LEFT] and [RIGHT]
button The output power of the flash light can be adjusted in major
steps through these buttons.
[UP] and [DOWN]
button and [OK] You can make fine tune power changes by pressing these
buttons and then press [OK] to set the fine tune setting.
[－] ZOOM [＋]
button By pressing these buttons, the head focal length of the flash
head can be cycled through (24 / 28 / 35 / 50 / 70 / 80 / 105).
[Pilot Button] Press to test the flash at the current output level.
Altri manuali per YN560
1
Indice
Altri manuali Yongnuo Flash della fotocamera
Yongnuo
Yongnuo RF605 Manuale utente
Yongnuo
Yongnuo YN-568EX II Manuale utente
Yongnuo
Yongnuo YN510EX Manuale utente
Yongnuo
Yongnuo YN862V Manuale utente
Yongnuo
Yongnuo YN968EX-RT Manuale utente
Yongnuo
Yongnuo YN560-III Manuale utente
Yongnuo
Yongnuo YN560 Manuale utente
Yongnuo
Yongnuo YN-568EX II Manuale utente
Yongnuo
Yongnuo YN300W Manuale utente
Yongnuo
Yongnuo YN686EX-RT Manuale utente
