York YJ-30 Guida rapida

SPLIT-SYSTEM

AIR-COOLED CONDENSING UNITS

YJ-30, -40 & -50

30 THRU 50 NOMINAL TONS

628792-BTG-G-0418

TECHNICAL

GUIDE

TECHNICAL

GUIDE

Description

These units are completely assembled, piped and wired at the factory

to provide one-piece shipment and rigging. Each unit is pressurized

with a holding charge of Refrigerant R-410A for storage and/or ship-

ping.

The compact design, clean styling, low silhouette, and quiet operation

make these condensing units suitable for almost any outdoor location.

On rooftops . . . because they weigh much less than a single package

unit of similar capacity and are much easier to rig and support. At

ground level . . . because their ample sub-cooling capacity allows them

to be located three or more stories below the evaporator coil.

Every condenser coil is pressurized with air to 325 psig and leak

tested. After assembly, the unit is pressurized with a combination of

Refrigerant R-410A and nitrogen to 450 psig for pressure testing and

additional leak testing. During this pressure test, the operation of the

high pressure control is checked. As the unit is being evacuated and

dehydrated, the operation of the low pressure control is checked.

Every compressor, condenser fan motor, crankcase heater, and elec-

trical control circuit is checked to assure a trouble-free start-up and

years of reliable operation.

The condenser fan guards are vinyl-coated to provide additional rust

protection and to enhance the appearance of the unit.

Compressors are mounted on rubber isolators to reduce the transmis-

sion of vibration. Vertical discharge condenser fans direct sound

upward and away from any surrounding structures.

All sheet metal parts are constructed of commercial grade galvanized

steel. After fabrication, each part is thoroughly cleaned to remove any

grease or dirt from its surfaces. The external parts are coated with a

powder paint to assure a quality finish for many years. This UL

approved coating system has passed the 750-hour, 20% salt spray

test per ASTM Standard B117.

All models include a 1-year limited warranty on the complete unit. An

additional 4-year extended compressor warranty is available as an

option on all models.

A matching line of Evaporator Blower units is also offered to meet your

precise capacity and air handling requirements.

628792-BTG-G-0418

2Ducted Systems

Table of Contents

DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

CONDENSING UNIT ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

GUIDE SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

PHYSICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

UNIT LIMITATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

COOLING RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

CAPACITY PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

SOUND PERFORMANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

ELECTRICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

TYPICAL WIRING DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

WEIGHT AND DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

628792-BTG-G-0418

Ducted Systems 3

Product Nomenclature

Product Category

Y = Split System, Condenser, AC, R-410A

Product Identifier

J = Standard Efficiency, 4-Pipe, R-410A

Nominal Cooling Capacity - MBH

-30 = 30 Ton

-40 = 40 Ton

-50 = 50 Ton

C00 = Cooling Only

Product Options

Installation Options

A = None

T = 208/230-3-60

W = 460-3-60

X = 575-3-60

Configured Split Condenser Model Number Nomenclature

A = Standard Motor

Airflow

Product Generation

2 = Second Generation

Voltage

Heat Type & Nominal Heat Capacity

YJ-30 C00 A TAAA 2A

Product Style

A = Style A

1 = Disconnect

B = Option 1

Options

AA = None

TA = Technicoat Condenser Coil

628792-BTG-G-0418

4Ducted Systems

Condensing Unit Features and Benefits

• Meets or exceeds ASHRAE 90.1 standards.

• Scroll compressors provide both high efficiency and reli-

ability.

•Simplicity®SE Controls

• Dual refrigerant circuits.

• Condenser coils are constructed of copper tubes and

aluminum fins for durability and long lasting efficient

operation.

• Crankcase heaters that will be de-energized when the

compressor is operating.

• Both high and low pressure controls. Since these con-

trols are self-contained, there are no capillary lines to be

damaged.

• Solid state or internal line break compressor motor pro-

tection.

• Class 2, 24-volt thermostat control circuit.

• Factory installed service valves are standard.

• Two filter-driers are shipped in the unit's control box for

field installation in the liquid line near the condensing

unit.

• Copper stub-outs are factory mounted on the suction

and liquid line service valves to simplify the field piping

connections.

• Multiple controls to provide stable system operation at

ambient temperatures down to 40ºF with kits available

for operation to 0ºF.

• Capacity staging for more economical operation and

more even temperature levels within the conditioned

space.

• Alockout circuit to prevent the unit from cycling on safety

control.

• Pump-out on unit startup to prevent liquid refrigerant

returning to the compressor is standard on all models.

• Inherently protected condenser fan motors.

• V-Coil Design with exterior service port connections.

• Five-minute anti-short cycle timer and minimum com-

pressor run time.

• Factory installed disconnect and Technicoat coils option.

• Self contained high and low pressure controls.

Condensing Unit Accessories

• Low ambient VFD control to 0° F.

• Phase Monitors - Designed to prevent unit damage. The

phase monitor will shut the unit down and out-of phase

condition.

• Hot Gas Bypass Kit - That will provide a metered flow of

compressor discharge gas to the system’s evaporator

coil during reduced load operation.

• Optional skid for fork truck handling (requires 96” length

forks).

628792-BTG-G-0418

Ducted Systems 5

Guide Specifications

SPLIT SYSTEM COOLING ONLY CONDENSING

UNITS

MODELS YJ-30, -40 AND -50

THE INSTALLER SHALL:

• Furnish Ducted Systemsair-cooled condensing units or

equivalent in accordance with the performance schedule

shown on the plans, and

• Install each unit as shown on the plans in accordance

with:

• The manufacturers recommendations and

• All applicable national and local codes

EACH UNIT SHALL BE:

• CSA approved.

• Completely assembled for one-piece shipping and rig-

ging.

• Leak pressure and functionally tested at the factory to

assure a trouble-free start-up after installation.

• Covered by a 1-year limited parts warranty on the com-

plete unit.

• In current production with published literature available

to check performance, limitations, specifications, power

requirements, dimensions, operation and appearance.

EACH UNIT SHALL HAVE:

• A steel angle frame to provide the rigid support required

for shipping, rigging and years of dependable operation.

• Zinc-coated steel that has been finished by a powder

paint process to provide a long lasting, quality appear-

ance.

• Removable panels for easy access to all internal compo-

nents during maintenance and service.

THE DIMENSIONS OF EACH UNIT SHALL:

• Not exceed those specified on the plans.

EACH COMPRESSOR SHALL:

• Be mounted on isolators to minimize the transmission of

vibration.

ALL CONDENSER COILS SHALL:

• Be draw through design.

• Be constructed of copper tubes arranged in staggered

rows and mechanically expanded into aluminum fins.

THE CONDENSER FAN MOTOR(S) SHALL:

• Be directly connected to the condenser fans.

• Have permanently lubricated ball bearings.

• Have inherent overload protection.

• Motors shall be three phase.

• The propeller-type condenser fans shall be arranged for

vertical discharge of the condenser air.

THE WIRING FOR EACH UNIT SHALL INCLUDE:

• A crankcase heater (one per compressor)

• All 24-volt temperature control circuit.

• Both high and low pressure cutouts.

• Solid-state or internal line break compressor motor pro-

tection.

• Condenser fan motor control to assure stable operation

at ambient temperatures down to 40ºF.

THE REFRIGERANT PIPING of each system shall include:

• A filter-drier shipped for field installation.

628792-BTG-G-0418

6Ducted Systems

Physical Data

YJ-30 thru -50 Physical Data

Component Models

YJ-30 YJ-40 YJ-50

Nominal Tonnage 30 40 50

REFRIGERANT

Refrigerant type R-410A R-410A R-410A

Holding charge (lb)1

1Holding Charge is the amount in the unit as shipped from the factory.

1.0 1.0 1.0

Operating Charge (lb)2

2Includes matched evaporator unit with 25 ft of piping.

System #1 35.0 47.0 51.0

System #2 35.0 47.0 51.0

DIMENSIONS (inches)

Length 128.5 128.5 128.5

Width 88.5 88.5 88.5

Height 37.5 57.7 57.7

WEIGHTS (lb)

Shipping 1875 2315 2345

Operating 1895 2347 2381

COMPRESSORS

Type Tandem Scroll Tandem Scroll Tandem Scroll

Quantity 2 2 2

Cooling

Nominal Capacity (Tons) System #1 15 20 25

System #2 15 20 25

Capacity Stages System #1 2 2 2

System #2 2 2 2

SYSTEM DATA

No. Refrigeration Circuits 2 2 2

Suction Line OD (in.) 1 5/8 1 5/8 1 5/8

Liquid Line OD (in.) 7/8 7/8 7/8

OUTDOOR COIL DATA

Face area (Sq. Ft.) System #1 32.5 45.5 52.0

System #2 32.5 45.5 52.0

Rows 222

Fins per inch 16 16 16

Tube diameter (in.) 3/8 3/8 3/8

Circuitry Type Interlaced Interlaced Interlaced

Refrigerant Control --- --- ---

CONDENSER FAN DATA

No. Fans / Diameter (in.) 4/30 4/30 4/30

Type Axial Axial Axial

Drive type Direct Direct Direct

No. speeds 1 1 1

Number of motors System #1 2 2 2

System #2 2 2 2

Motor HP (ea.) 1 1/2 1 1/2 1 1/2

Rotation3

3When viewing the shaft end of the motor.

CW CW CW

RPM 1140 1140 1140

Nominal CFM System #1 15400 19400 19900

System #2 15400 19400 19900

628792-BTG-G-0418

Ducted Systems 7

Unit Limitations

Cooling Ratings

EER = Energy Efficiency Ratio at full load - the cooling capacity in Btu’s per hour (Btuh) divided by the power input in watts, expressed in Btuh per

watt (Btuh/watt).

EER; condensing unit only ratings based on 45º F SST and 95ºF entering outdoor air temperature.

LEGEND

EER = Energy Efficiency Ratio

SST = Saturated Suction Temperature

Condenser Unit limitations

Model Nominal

Tonnage Unit Voltage Applied Voltage1

1Rated in accordance with AHRI Standard 110, Range “A” Utilization Voltage.

Outdoor DB Temp Cooling (°F) Indoor DB Temp Cooling (°F)

Min2

2Low Ambient accessories are available to permit stable system operation at ambient temperatures down to 0°F.

Cooling Ratings

Max Max Min†Max Min

YJ-30 30 208/230-3-60 187 252 125 40 86 68460-3-60 432 504

575-3-60 540 630

YJ-40 40 208/230-3-60 187 252 125 40 86 68460-3-60 432 504

575-3-60 540 630

YJ-50 50 208/230-3-60 187 252 125 40 86 68460-3-60 432 504

575-3-60 540 630

Outdoor

Unit

Condensing Unit Only

Gross Capacity1

(MBH)

1Condensing unit only ratings are at 45 F SST and

95 F entering-air temperature.

kW EER

YJ-30 333 29.9 11.1

YJ-40 469 37.4 12.5

YJ-50 576 50.0 11.5

628792-BTG-G-0418

8Ducted Systems

Capacity Performance

Condenser Only Cooling Capacities

YJ-30 thru -50 Condenser Only Capacities

MODEL

Suction Press. &

Corresponding

Temp. @ Saturation

Temperature of Air on Condenser Coil, °F

65 75 85 95 105 115

PSIG °F MBH KW EER MBH KW EER MBH KW EER MBH KW EER MBH KW EER MBH KW EER

YJ-30

104 35 275.4 28.5 9.6 264.0 27.4 9.6 250.0 26.4 9.5 238.2 28.8 8.3 231.8 32.0 7.2 228.5 35.1 6.5

117 40 327.9 29.2 11.2 316.0 28.1 11.3 302.0 27.0 11.2 285.8 29.4 9.7 273.0 32.5 8.4 263.3 35.6 7.4

129 45 380.4 29.8 12.8 368.0 28.7 12.8 354.0 27.5 12.9 333.5 29.9 11.1 314.2 33.0 9.5 298.1 36.2 8.2

142 50 432.9 30.4 14.3 420.0 29.3 14.3 406.0 28.1 14.4 381.1 30.5 12.5 355.4 33.6 10.6 332.9 36.7 9.1

154 55 485.4 31.0 15.7 472.0 30.0 15.8 458.0 28.7 16.0 428.8 31.0 13.8 396.6 34.1 11.6 367.7 37.2 9.9

YJ-40

105 35 418.0 33.2 12.6 408.0 32.4 12.6 399.2 32.4 12.3 397.3 36.2 11.0 389.6 40.4 9.6 389.2 45.0 8.6

117 40 461.0 34.4 13.4 451.0 33.5 13.5 441.6 33.1 13.3 433.0 36.8 11.8 419.2 40.9 10.3 410.8 45.2 9.1

130 45 504.0 35.6 14.1 494.0 34.6 14.3 484.1 33.8 14.3 468.8 37.4 12.5 448.9 41.3 10.9 432.4 45.4 9.5

142 50 547.0 36.9 14.8 537.0 35.7 15.0 526.5 34.5 15.3 504.5 38.0 13.3 478.5 41.8 11.5 454.0 45.6 9.9

155 55 590.0 38.1 15.5 580.0 36.8 15.8 569.0 35.2 16.2 540.3 38.5 14.0 508.2 42.2 12.0 475.6 45.8 10.4

YJ-50

105 35 489.4 45.3 10.8 487.2 44.1 11.0 482.6 43.4 11.1 442.2 48.4 9.1 391.3 54.4 7.2 334.0 60.7 5.5

118 40 561.4 46.2 12.1 558.7 45.2 12.4 554.6 44.4 12.5 509.2 49.4 10.3 456.8 55.1 8.3 400.0 61.1 6.5

130 45 633.4 47.2 13.4 630.2 46.3 13.6 626.6 45.4 13.8 576.2 50.5 11.4 522.3 55.9 9.3 466.0 61.5 7.6

142 50 705.4 48.2 14.6 701.7 47.4 14.8 698.6 46.4 15.1 643.2 51.3 12.5 587.8 56.6 10.4 532.0 62.0 8.6

154 55 777.4 49.2 15.8 773.2 48.5 15.9 770.6 47.4 16.2 710.2 52.3 13.6 653.3 57.4 11.4 598.0 62.4 9.6

628792-BTG-G-0418

Ducted Systems 9

Sound Performance

Outdoor Sound Power Levels (dB), 60 Hz

Model Nominal

Tonnage dB(A)1

1Rated in accordance with AHRI 270 Standard.

Electrical Data

Octave Bands (Hz)

63 125 250 500 1000 2000 4000 8000

YJ-30 30 92 90 93 91 89 87 83 79 74

YJ-40 40 92 90 93 91 89 87 84 80 75

YJ-50 50 93 91 94 92 90 87 84 80 75

YJ-30 thru -50 Electrical Data

Model Compressors Outdoor Fan Motor Minimum

Circuit

Ampacity

Maximum

Fuse Size

(A)

Power

Supply Qty RLA

(each) MCC

(each) LRA

(each) Power

Supply HP Qty FLA

(each)

YJ-30

208/230-3-60 4 25.0 39 164 208/230-3-60 1 1/2 4 5.8 129.5 150

460-3-60 4 12.2 19 100 460-3-60 1 1/2 4 2.9 63.5 70

575-3-60 4 9.0 14 78 575-3-60 1 1/2 4 2.2 47.1 50

YJ-40

208/230-3-60 4 30.1 47 225 208/230-3-60 1 1/2 4 5.8 151.1 175

460-3-60 4 16.7 26 114 460-3-60 1 1/2 4 2.9 82.6 90

575-3-60 4 12.2 19 80 575-3-60 1 1/2 4 2.2 60.7 70

YJ-50

208/230-3-60 4 48.1 75 245 208/230-3-60 1 1/2 4 5.8 227.6 250

460-3-60 4 18.6 29 125 460-3-60 1 1/2 4 2.9 90.7 100

575-3-60 4 14.7 23 100 575-3-60 1 1/2 4 2.2 71.3 80

628792-BTG-G-0418

10 Ducted Systems

Typical Wiring Diagrams

Typical 208/230 Volt, YJ-30/-40/-50 Condensing Unit Wiring Diagram

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Pompa di calore popolari di altre marche

MICROWELL

MICROWELL HP 1000 GREEN Manuale utente

Sanyo

Sanyo SAP120FCH Manuale utente

Daikin

Daikin EHYHBH05AA Manuale utente

Panasonic

Panasonic WH-SDF03E3E5 Guida

Bryant

Bryant 544B Manuale utente

Airxcel

Airxcel 45000 Series Manuale

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Manuale utente

Dimplex

Dimplex LI 16I-TUR Guida utente

Carrier

Carrier WSHP Open v3 Guida rapida alla configurazione

TGM

TGM CTV14CN018A Manuale utente

Carrier

Carrier 38MGQ Series Manuale utente

Kokido

Kokido K2O K880BX/EU Guida alla risoluzione dei problemi

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Guida rapida

Carrier

Carrier 48EZN Manuale utente

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Istruzioni operative

Ariston

Ariston NIMBUS Manuale utente

Weishaupt

Weishaupt WWP L 7 Guida utente

GE Zoneline AZ85H09EAC Manuale utente