Yudo ACT-D800 Manuale utente

INSTRUCTION MANUAL
TYPE ACT-D800
Sequence Injection Controller
Version 5.5
Sequence Injection Controller

Thank you for using YUDO production
感谢贵公司使用YUDO产品
Contents
目录
1、Environments ……………………………………………………2
使用环境
2、Composition of Control Module ……… …………………………2
PCB 结构
3、Central Processing Unit ……………………………………………2
主要控制装置
4、Input ………………………………………………………………2
输入因素
5、Display ……………………………………………………………3
显示因素
6、Output ………………………………………………………………3
输出因素
7、Start to Run…………………………………………………………4
使用说明
8、Menu Setting………………………………………………………5
动态说明
9、Mode Specification ………………………………………………7
模式规格
10、System Application ………………………………………………8
系统应用程序
11、Wiring Specification………………………………………………9
外部线连接图
Before using the product ,please read this instruction manual carefully to
avoid any damage due to improper usage. If you have any questions, please do
not hesitate to contact our Head Office or YUDO Territory Sales Branch.
使用本产品前,敬请仔细阅读此手册,以免在操作过程中的失误。
如有任何疑问,敬请与柳道公司总部联系或柳道所在地分公司联系。
1

1、Environments 使用环境
1)Main Power Input:AC220V(50-60Hz)
启动电源:AC220V/50-60Hz
2)Signal Input Power:DC24V or AC220V
信号输入电源: DC24Vor AC220V
3)Solenoid Valve Output Power:DC24V(Less than 100mA pet GATE)or
AC220V(Total less than 1A)
螺旋管针阀输出电源: DC24V(每GATE100mA以下)或者AC220V(1A以下)。
2、Composition of Control Module PCB构成
1)CONTROLPCB:Power unit,MICOM, Input/output unit
控制器PCB:电源部,MICOM,输入输出部。
2)DISPLAY PCB : Display unit Switch.
显示器PCB:显示部,开关输入部。
3、Central Processing Unit 主要控制装置
1) S.M.P.S ①: To transform input AC220V to DC24V/1A,DC5V/1A.
S.M.P.S : 把AC220V电源转换成内部驱动电源DC24V/1A,DC5V/1A。
2) M.P.U : To control input/output and display.
微处理器:输出控制及显示器控制。
3) RELAY : Solenoid Valve running element (DC24V or AC220V output).
继电器:螺旋管针阀驱动元件(DC24V或者AC220V输出)
4、Input :
①S.M.P.S: Switching Mode Power Supply
2
①
②
③
④
⑤
⑥
⑦
⑧
SEQUENCE INJECTION CONTROLLER
GATE1 DEL OPEN
A
B
GATE2 DEL OPEN
A
B
GATE3 DEL OPEN
A
B
GATE4 DEL OPEN
A
B
GATE5 DEL OPEN
A
B
GATE6 DEL OPEN
A
B
GATE7 DEL OPEN
A
B
GATE8 DEL OPEN
A
B
DC24V
AC220V
SIGNAL
POWER
MODE
OPEN
ACT-D800
ENTER
USER’S MANUAL

a. To select motion mode ( mode A>mode B>gate off) for each gate.
设定各窗口的动作模式(MODE A >MODE B>GATE off)时使用。
b. To set unit of each gate(999/99.9/9.99).
设置各GATE的使用单位(999/99.9/9.99)时使用。
a. To open manually a gate or all gate.
各GATE或者全部GATE以手动OPEN时使用。
a. To move to gate for setting.
设定GATE时,来回移动时使用。
b. To set or to move
设定设置值或移动位置时使用。
a. To select gate for setting.
选定要设置的GATE时使用。
b. To finalize set or to exit the gate selected.
完成设置 或者从现在已选定的GATE中退出时使用。
a. To turn On/Off time.
对定时器进行ON/OFF时使用。
5、Display 显示因素
1)Display delay time and open time of each gate in display panel.
各GATE的延迟时间和OPEN时间显示在数码管上。
2)Display LED on while each gate opens.
各GATE的OPEN输出期间以LED显示。
3)Display MODE A or Bof each gate with LED.
各GATE的MODE A或者 MODE B以LED显示。
4)Display output voltage(DC240Vor AC220V)to Solenoid Valve with LED.
以指示灯LED表示螺旋管针阀输出,输出电压(DC24V或AC220V)。
5)Display LED on while signal is on.
SIGNAL输入时间期间以指示灯LED显示。
6、Output 输出因素
1)Put out DC24V or AC220V via relay for the open time of each gate.
各GATE的OPEN输出期间把DC24V或者AC220V通过RELAY接点输出。
①
②
③ ④
⑤
⑥
⑦
⑧
3
MODE
OPEN
POWER
ENTER

7、Start to Run 使用说明
1)Connect cables
输入及输出电源连接
Connect to main input power, signal input from injection machine, output to mold.
Make sure the main input voltage (see rear of time case), output voltage to mold.
按照时间控制器的电源式样(请参考外壳后部)连接电源线与输入,输出线。
2)Power LED is blinking while power on.
输入电源时POWER LED闪灯。
3)Switch between actions
工作状态转换
A. Press key.
按键启动电源。
a. POWER LED blinks.
POWER LED 闪灯。
b. Display delay time value and open time value at each display panel.
根据GATE的延迟时间及OPEN时间,把所设置标在GATE上。
4)Switch between MODE A/MODE B and gate off.
mode A/ mode B 及窗口off 转换。
A. Press for 4 seconds.
按4秒左右 键。
a. Buzzer rings and mode LED blinks.
响警告声,MODE LED 闪灯
b. MODE LED of 1st gate blinks.
1号GATE的MODE LED 闪灯
c. Hit , to switch MODE A/B and gate off.
MODE A/B及GATE OFF 的转换是利用 ,转换。
d. MODE A or B LED blinks,Both MODE A and B LED blink when gate off.
转换时相关MODE A/B 的LED 闪亮,GATE OFF 时MODE A/B全部闪亮。
e. Move using , between GATE.
GATE选择是利用 ,移动自己需要的GATE。
f. When move, MODE A or B LED is Blinking in the gate.
移动时相关GATE的MODE A或者MODE B LED闪灯。
4
POWER
POWER
MODE
MODE
USER’S MANUAL

g. Press to save, or keep idle for 4 seconds to automatic save.
按 完成设置,位置移动后过4秒后也会自动完成设置。
h. When gate off, all display is off (MODE A/B LED,DEL/OPEN display panel off)
OFF时,GATE A/B mode LED 和平DEL/OPEN 表示窗将灭灯。
5)Switch between units(999/99.9/9.99)
使用单位的(999/99.9/9.99)转换。
Move the gate using , , and press for 4 seconds to confirm.
使用方向键盘 , 选择相关GATE, 换4秒左右。
a. Buzzer rings and MODE LED Blinks.
响警告声,MODE LED 闪灯。
b. “Unl” displays in DEL panel and 999 “or 99.9/9.99” display in OPEN panel.
相关GATE的LED 显示窗口显示“Unl”, OPEN显示窗口显示(999/99.9/9.99)。
c. Switch units using , .
使用单位变更是利用 , 变更。
d. Move gate using , .
GATE移动是利用 , 来移动。
e. Hit to save, or keep idle for 4 seconds to automatic save.
按 完成设置,位置移动后过4秒后也会自动完成设置。
6)Manual open
手动OPEN输出
A:ALL OPEN
全部OPEN输出
a. It keep open while pressed.
按 期间输出OPEN
B:A gate OPEN
只对相关GATE进行OPEN输出。
a. Move using , , , to get gate.
利用方向键盘选择GATE
b. It keeps open the gate while pressed.
按 期间只对相关GATE进行OPEN输出。
4
ENTER
MODE
ENTER
MODE
POWER
POWER
OPEN
OPEN
OPEN
OPEN

8、Menu Setting 动态说明
1)MODEA 模式A
7)Set DET time:
DET时间设置:
Move using Direction Key to get gate and its DEL panel, to confirm.
使用方向键盘移动到相关GATE的DET显示窗口后按 。
a. Right digit in DEL panel blinks.
选择的GATE DEL 显示窗口,右边位置的设定值会闪亮 。
b. Set time using , .
时间设置利用 , 选定。
c. Move between digits using , ,
位数移动是利用 , 移动。
d. Hit to save, or keep idle for 4 seconds to automatic save.
按 完成设置,位置移动后过4秒后也会自动完成设置。
8)Set OPEN time
OPEN时间设定
Move using , , , to get gate and its OPEN panel,
to confirm.
使用 方向键盘移动到相关GATE 的OPEN 显示窗口后按 。
a. Right digit in OPEN panel blinks.
在选择的GATE的OPEN显示窗口上,右边位置的设定值会闪亮。
b. Set time using , .
设定值的变更是利用 , 选定变更。
c. Move between digit using , .
移到自己需要的位置时按 , 。
d. Hit to save, or keep idle for 4 seconds to automatic save.
按 完成设置,位置移动后过4秒后也会自动完成设置。
5
INJECTION
SIGNAL
DELAY
OPEN
Signal On Signal Off
MODE A动作
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
USER’S MANUAL

i) Example 例如:
a. In case injection signal =10sec and DEL time =4sec, then after DEL time, it
opens (Relay ON) for 6sec.
注塑时间:10秒, DEL 时间: 4秒,按到注塑信号过4秒后, GATE 以OPEN 状态维持6秒钟后
将自动关闭.。
b. For the delay time, it counts down and displays it in DEL display panel, and just
after DEL time, it opens (Relay ON).
把延迟的DEL时间倒数计秒(Down Count),标在DEL表示窗口, 在DEL时间完成后开始OPEN输出。
c. In case injection signal is off before delay time passed, it resets to set time.
如在延迟时间结束之前注塑信号先结束, 就开始设定时间初始化。
d. Even after DELAY time passed, injection signal is keeping on, it opens, and it counts
up the open time and displays it in OPEN display panel.
如在延迟时间结束之后注塑信号还在继续输入, 就继续输出OPEN。
e. When injection signal is off ,delay set time will be display in DEL display panel, and
OPEN display panel displays counted open time until next injection signal comes on.
如注塑信号结束,延迟设定时间就显示在DEL显示窗口, OPEN在下次注塑信号开始之前一直维
持Up Count 的OPEN 时间, 并将值显示在OPEN显示窗口。
5
2)MODE B 模式 B
INJECTION
SIGNAL
DELAY
OPEN
t1 Signal On t2 Signal Off
MODE B 动作
T
Example
a. In case injection signal=10sec, DEL time=4sec, and OPEN time=4sec, then when
injection signal comes on, after DEL time, it opens for OPEN time (4sec).
注塑时间:10秒, DEL 时间: 4秒, OPEN时间: 4 秒,按到注塑信号过4秒后, GATE 以OPEN 状态
维持4秒钟后将自动关闭。

b. For the delay time, it count down and displays it in DEL display panel, and just after
DEL time, it opens for OPEN time and it counts down from the OPEN set time and
displays it in OPEN display panel.
把延迟的DEL时间倒数计秒, 标在DEL表示窗口, 在DEL时间完成后开始OPEN时间期间,OPEN时
间从设定值开始倒数计秒, 并标示在OPEN显示窗口。
c. In case injection signal is off before delay time passed, it resets to set time.
如在延迟时间或OPEN时间结束之前, 注塑信号先结束, 就开始设定时间初始化。
d. In case injection signal is off before open time passed, it resets to set time.
OPEN时间终止前注塑信号终止时往设定时间初始化.
e. When injection signal is off, delay set time and open set time will be displayed
DEL display panel and OPEN display panel respectively.
注塑信号结束,延迟设定时间和OPEN 设定时间, 就标示在DEL 显示窗口和OPEN显示窗口。
6
3)MODE C 模式 C
INJECTION
SIGNAL Del1
Open1
t1 Signal On t2 Signal Off
MODE C 动作
Open2
Del2
T
Example
a. In case injection signal=10sec, DEL time Del1=2sec, OPEN time Open1=4sec, and
Del2=1sec and Open2=4Sec. then when injection signal comes on, after DEL time, it
opens for OPEN time (4sec).
注塑时间:10秒, Del1时间: 2秒, Open1时间: 3秒, Del2时间: 1秒, Open2时间:4秒。按到注塑信号
过2秒后, GATE 以OPEN 状态维持3秒输出动作自动关闭,然后保压1秒钟后, GATE 以OPEN
状态维持4秒钟后输出动作将自动关闭。
b. For the delay time, it count down and displays it in DEL display panel, and just after
DEL1 time, it opens for OPEN1 time and it counts down from the OPEN1 set time and
displays it in OPEN display panel.
把延迟的DEL1时间倒数计秒, 标在DEL表示窗口, 在DEL1时间完成后开始OPEN1时间,OPEN1时
间从设定值开始倒数计秒并标示在OPEN窗口输出动作。在Open时间完成后开始Del2时间,Del2
时间从设定值开始倒数计秒,标在DEL表示窗口。在DEL2时间完成后开始OPEN2时间,OPEN2
时间开始倒数,标在OPEN窗口并输出动作。
USER’S MANUAL

c. In case injection signal is off before delay time passed, it resets to set time.
如在延迟时间或OPEN时间结束之前, 注塑信号就开始设定时间初始化。
d. In case injection signal is off before open time passed, it resets to set time.
OPEN时间终止前注塑信号终止时往设定时间初始化.
e. When injection signal is off, delay set time and open set time will be displayed
DEL display panel and OPEN display panel respectively.
注塑信号结束,延迟设定时间和OPEN 设定时间, 就标示在DEL 显示窗口和OPEN显示窗口。
7
3)Other Menu
其它显示动态及功能
A: Output Voltage Indicator
标出输出电压
a. Select output voltage DC24V orAC220V in compliance with Solenoid valve.
输出电压是根据螺旋管针阀可选DC24V或者AC220V。
b. Display output voltage in DC24V LED or AC220V LED.
输出电压是根据螺旋管针阀可选DC24V或者AC220V。
B: Input ON/OFF Indicator
输入ON/OFF 标示
a. When input is on, SIGNAL LED is on.
输入ON/OFF 标示
b. When input is off, SIGNAL LED is off.
输入OFF-SIGNAL LED 关闭。
9、Mode Specification
◆ModeA
Selecting mode A: After the injection signal has
been received, the gate is continuously closed
during the DEL Time(t1),After the DEL time has
elapsed, the gate Opens and will remain opened
until the end of the injection signal.
选择模式A: 接收到注塑信号后, 在延迟时间内,浇口是关
闭的,在(DEL时间)消失后,浇口打开且一直保持开着状态,
直到注塑时间信号结束。
T t 1 3 sec 10sec
Signal ON Signal OFF
t1: Delay Time
Gate Open
Indice

















