Z-CAM K1 Pro Manuale utente
Z CAM™ K1 Pro
User Manual (Draft)
v1.0
1. INTRODUCTION
Camera Introduction
Display Information
LED Indicator Status
• Green: When the camera is turned on with SD card in the slot.
• Red: When the camera is turned on but no SD card in the slot or the SD.
• Flashing Green: When the camera is recording, LED indicator will flash every second.
• Flashing Red (normal): When the SD card memory is full, LED indicator will flash every
500ms.
• Flashing Red (fast): When the camera is overheated, LED indicator will flash every
200ms.
2. CAMERA SETUP
2.1. Install / Take Out Memory Cards
1) Insert 2 SD cards into the slots with correct direction (indicated by the icon beside the slot)
2) To take out the SD card, press down the SD card and it will eject from the slot.
* It is highly recommended to use SanDisk Extreme PRO® SDXC UHS-I memory cards. (Note that the camera
supports SDXC memory cards up to 128GB capacity.)
2.2. Power On / Off The Camera
1) Connect the LEMO power cable to the camera.
2) Connect the D-TAP connector to the LEMO power cable. *
3) Connect the D-TAP connector to the AC/DC power adapter, and select the proper AC
power cable to plug to a power socket, the camera will be powered on automatically when
the power is connected for the 1st time.
* Please note that with LEMO power cable you can also connect to a battery or external power supply with D-TAP
socket, and hot swap is supported.
4) To power off the camera, long-press the Power button until the LED indicators are off.
2.3. Camera with PoE (Power over Ethernet)
To us e Po E as po we r s up pl y f or th e c am er a, yo u w ou ld ne ed a r ou ter o r sw it ch * with PoE
function, with output power not less than 15.4W for each port, and the output voltage should be
48V for each port.
* Please note that a switch with PoE can only used for power supply, and you would need a
router with PoE if need control and live viewing with the camera.
2.4. Ethernet Connection (to Computer)
With Ethernet connection to a computer (PC/Mac), you can control the camera and download
files with Z CAM™ Controller (4. CAMERA CONTROL), and do live streaming with Z CAM™
WonderLive (8. LIVE STEAMING, PC only).
There are 2 ways of connection: Direct Mode & Router Mode.
Direct Mode (default)
Connect the camera to the computer directly with an Ethernet cable. It’s default setting of the
camera.
Router Mode
1) Change the “Network” setting to “Router” in Z CAM Controller (PC / Mac) or Z CAM VR
app (mobile device).
2) Connect the camera to a router with an Ethernet cable, and then connect the router to the
computer via Ethernet network or WiFi.
2.5. WiFi Connection (to Mobile Device)
With WiFi connection to a mobile device (iPhone/iPad/Android device), you can control the
camera with Z CAM VR app installed on the mobile device (7. REMOTE CONTROL). Here are
the steps to set up WiFi connection.
1) Make sure the WiFi is activated (a WiFi icon on the display). If not, long press the Info
Button for 5 seconds, then there will be a WiFi icon on the display, which means WiFi of
the camera is activated.
2) Connect the mobile device to the camera with correct WiFi ID (start with ZCAM-K1P),
and default password is 12345678. You can change the password in the Z CAM VR app.
* Please note that the camera has built-in antenna, and would suggest to have external antenna installed as to get
better WiFi coverage and signal.
2.6. Camera Reset
If you want to reset the camera, long press the Record button for 5 seconds, then the camera
will restart with all the settings back to factory setting.
3. RECORDING
3.1. Before Recording
Please do the following check before recording:
1) Check the Aperture of both lens and make sure they are aligned. You can turn the
Aperture Ring to adjust it and make sure it’s in the right position (with the white line on
the Aperture Ring pointing to the number).
2) Format both SD cards with Z CAM™ Controller on a PC (4. CAMERA CONTROL) or
with Z CAM VR app on a mobile device (5. REMOTE CONTROL).
3) Make sure the camera is in a horizontal position.
3.2. Start / Stop Recording
1) Press the Record button to start recording. Time of recording will be indicated on the
displays.
2) While it’s recording, press the Record button again to stop recording.
4. REMOTE CONTROL (with Z CAM VR app)
Z CAM VR is a mobile app (iOS only for now) to control the camera through WiFi connection.
You can download it from Apple’s App Store.
4.1. Connect to The Camera
1) Make sure the mobile device is connected to the camera through WiFi, please refer to 2.5
WiFi Connection.
2) Open the Z CAM VR app, and there will be a list of the camera connected. Select the
camera and it will come into the main screen. You can select one of the camera (lens) or
All Cameras (both lenses) from the top menu.
4.2. SD Cards Format
Tap the Setting button and select Format card, there will be a pop-up window to confirm the
formatting. Tap Format if you want to format the cards.
Please note that all the data will be erased from the cards after formatting!
4.3. Recording
Tap t he Record button to start recording, and Tap Stop button to stop it.
4.4. Timelapse (Video)
1) Swap to select Timelapse mode and tap Record button to start recording.
2) Timelapse interval can be modified in the Settings.
4.5. Camera Settings
There are 3 tabs at the bottom of the main screen including: Settings, White Balance,
Exposure, which you can change the settings of the camera*. Please check the User Manual
of Z CAM VR for more details.
* We would suggest to keep Coordination of White Balance & Exposure as Enable as to get
a good result of video footage.
5. CAMERA CONTROL (with Z CAM™ Controller)
Z CAM™ Controller (PC & Mac) is a software that provides basic control features of all Z
CAM™ VR cameras. Ethernet or WiFi connection is required for camera control.
Altri manuali per K1 Pro
1
Indice
Altri manuali Z-CAM Macchina fotografica digitale
