Zanflare F1 Manuale utente

F1 Flashlight
zanflare Manual
Congratulaons for purchasing our zanflare flashlight. You have chosen a high quality product
designed from the latest technology. For the best use of our products, please read the instrucon
manual carefully.
Spezifikaonen
Features
Cree XP-L (V6) LED with a lifespan of 50,000 hours.
Maximum output of 1240 lumens.
High efficiency circuit board provides up to 550 hours runme on moonlight, delivers constant
current to the LED regardless.
Boasts a peak beam intensity of 16650cd; throw distance up to 252 meters; light angle reached 60°.
‘Crystal Coang Technology’ combined with ‘Precision Digital Opcs Technology’ provide
extreme reflector performance.
Toughened ultra-clear mineral glass with an-reflecve coang.
Distance 252m
Beam intensity 16650cd
Special mode SOS, Strobe
Impact 1.5m
LED Cree XP-L(V6)
Baery (not included) CR123A * 2; RCR123 * 2; 18650 * 1
Package contents
96gWeight
Light angle 60°
Waterproof IPX-8, 2m
Quality holster, lanyard, clip, manual, spare O-ring(baery not included)
Dimensions Length:136mm Head:28mm Tail:26.5mm
Mode Mid Low MoonlightFlare High
Output 50lm 1lm290lm1240lm 590lm
30s 2h 30min 6h 22h 550hRunme

Made of light weight, high strength aero grade aluminum, alloy with HAIII military grade
hard-anodized finish.
High-efficiency regulaon circuit provides unwavering output.
Reverse polarity protecon guards against improper baery installaon.
Low-voltage warning funcons remind you to replace the baery. When the voltage was under
2.6V, the LED would blink 3 mes and then turn off.
Intelligent memory funcon.
Mode switch interface provides one-handed operaon and easily access to all funcons.
Machined from a solid aluminum bar give F1 its superior shock and impact resistance.
All metal outer appearance and metal nut provide IPX-8 highest grade waterproof and weather
two meters submersible adventure.
Micro USB charging port and indicator; fully charging me is 4 hours.
Stainless steel tanium-plated clip include.
Tail stand capability, an-roll, slip-resistant body design.
Tail safety hammer.
Tail on/off switch.
Baery specificaons
Type Dimensions Nominal voltage Recommended
Rechargeable baery(Li-ion)
Rechargeable baery(Li-ion)
Non-rechargeble baery(Lithium)
18650*1
RCR123*2
CR123A*2
3.7V
3V
3.7V
√
√
Baery installaon
Insert one 18650 baery or two CR123 baeries with the posive pole poinng forward the light
head.
Unscrew the tail switch cap and inset.
Ensure baeries are inserted with the posive (+) end poinng to the head. The F1 will not
operate with incorrectly inserted baeries.
Baeries are not included.
PLZ note: If the tail cap is not ghtened snugly, the flashlight will not turn on.

General operaon
Press the tail switch to turn the light on; press again to turn the light off.
With the light turned on, press the mode switch in quick succession to cycle through the
following brightness levels: Moonlight Low Mid High
Double click the mode switch to enter into Flare mode.
With the light turned on, press and hold the mode switch for 2s to acvate Strobe mode. Press
again to cycle through SOS or Strobe mode.
→ → →
Turn on/off
Press to cycle
through: Moonlight
→ Low → Mid → High
Double-click to
enter Flare mode
Hold on for 2s to acvate strobe
→ Press again and hold on for 3s
to acvate SOS

Power ps
The indicator turned red: in charging
The indicator turned green: finished charging
The LED blink: remind you of changing the baery or recharging
When the voltage was under 2.8V, the LED would blink once per minute.
When the voltage was under 2.6V, the LED would blink 3 mes and then turn off.
Plz note: Twist the protecve ring around the USB and indicator, in order to prevent water or dust.
Maintenance
Do not disassemble the sealed head. Doing so can cause damage to the flashlight and will void
the warranty.
Use high-quality baeries or you run the risk of the flashlight being damaged by electrolyte
leakage or baery breakage.
If the flashlight will not be used for a long me, remove the baeries to avoid damage caused
from baery leakage.
Every 6 months, threads should be wiped with a clean cloth followed by a thin coang of
silicon-based lubricant.
Garane
3 Days DOA warranty: If the product you purchased becomes defecve within 3 days of receipt,
we will replace the item free of charge.
30 Days free return: Any item can be returned to get refund within 30 days of receipt in new
condion if you don't like it.
3 years free repair/replacement: Any lighng product sold by zanflare direct at Amazon Stores
which is found to be defecve under normal use and service within 3 years and more than 30
days counng from the date of purchasing with proof of purchase can be replaced with new
ones freely.
Lifeme limited warranty: For items purchased aer 3 years, we will sll provide warranty service,
but the cost of labor costs and maintenance with the exclusion of accessories or replacement
parts will be paid by the customers.
For the latest informaon on zanflare® products and services, please go to: www.zanflare.com
Hold the mode switch again for 2s to exit SOS or Strobe mode.
F1 automacally memorizes the last brightness level used aer turning on.
Plz note: In order to prevent overheang, F1 automacally access a lower brightness mode.
Indice
Altri manuali Zanflare Torcia elettrica


















