Zavio D8520 Manuale utente

0



86085A3000030

ZAVIOMotorizedOutdoorIRDome

QuickInstallationGuide

1



Quick Installation Guide

Please follow the installation steps below to set up your IP camera.

Check the package contents with the list below. See P.1

Physical overview. See P.2

I/O Terminal Block Circuit. See P.3

I/O Terminal Block Pin Definition. See P.3

LED Indicator Definition. See P.4

Power Mode. See P.4

Installation of hardware and connection of all cables. See P.4

Windows: Go to Zavio website and download Camera Installation Tool. See P.8

Access the IP Camera using Camera Installation Tool. See P.9

MAC OS: using Safari Browser. See P.11

Lighting environment. See P.13

Change language of the web interface. See P.13

Application of IP Camera. See P.14

Package contents

Camera IP camera

Quick Installation Guide Brief product information and quick installation

Accessory Mounting plate

Screw pack for wall and ceiling mounting

Alignment sticker

L-type hex key wrench

2pin I/O terminal block for power adaptor (12V DC)

Software

The following software and information are available online:

-Video Management Software

-Camera Installation Tool

-User manuals

-Camera Language Packs

Download the above at http://www.zavio.com/downloads.php or scan QR-Code.

ToactivateVideoManagementSoftware,pleaseenterthelicensekeybelow.

2



Dome bubble

Physical overview



Conduit hole

Network / PoE

Lens

SD card slot

Reset

Network Link status indicator

Power status indicator

DC 12V/1.5A

Light Sensor

IR LEDs (16units,

Distance 20m)

Fan

RCA

Smart focus

control

NTSC/ PAL

switch

SD Card status indicator

I/O Terminal Block:

1: Ground,

2: +12VDC,

3: Audio in,

4: Audio out,

5: Digital Output 1,

6: Digital Output 2,

7: Digital Input 1,

8: Digital Input 2

3



I/O Terminal Block Circuit

I/O Terminal Block Pin Definition

PIN Definition Description Max. V/A

1 Ground -

2 + 12VDC

12V DC

1.2 W

3 Audio In Unbalanced, 1.4Vp-p, 1Vrms, terminal block -

4 Audio Out Unbalanced, 1.4Vp-p, 1Vrms, terminal block -

5 Digital

Output 1

Uses an NPN transistor with the emitter connected

to the GND pin. If used with an external relay, a

diode must be connected in parallel with the load for

protection against voltage transients.

100 mA

24V

6 Digital

Output 2

Uses an NPN transistor with the emitter connected

to the GND pin. If used with an external relay, a

diode must be connected in parallel with the load for

protection against voltage transients.

100 mA

24V

7 Digital Input

1 Connected to GND to activate, or leave floating (or

unconnected) to deactivate. 30V DC

8 Digital Input

2 Connected to GND to activate, or leave floating (or

unconnected) to deactivate. 30V DC

DEVICE1

AUDIO_IN

AUDIO_OUT

DC 12V

GND

AUDIO_IN (+)

AUDIO_OUT (+)

DO-1

CAMERA

DI-2

DI-1

DO-2

DEVICE2

DIODE

RELAY 1

DIODE

RELAY 2

SW1

SW2

4



LED Indicator

LED Color Indication

Network Blue Solid blue when network is established.

Blink blue when there is network activity.

Power Red Solid red for booting up process

Blue Solid blue for booting up completion

Unlit When reset button pressed for at least 5 sec.to factory default

SD Card Yellow Solid yellow means SD card ready

Blink yellow while accessing SD card



Power Mode

PoE

Mode

at Power Requirement PoE (IEEE802.3at) with Class 4

Power Consumption 14.05 W, with max. IR (100%) and Fan on

af Power Requirement PoE (IEEE802.3af) with Class 3

Power Consumption 10.81 W, with max. IR (70%) and Fan on

Adaptor

Mode Power Requirement 12V/1.5A Adaptor

Power Consumption 14.26 W, with max. IR and Fan on

Note: Fan will activate when temparature is above 50ºC and turn off when drops under 45ºC.



Install the hardware and connect all cables

A. Hardware installation

a) Connect power adaptor to the supplied 2pin I/O terminal block. Make sure the red

wire of the power adapter is connected to the positive pole of the terminal block.

b) Loosen the tamper-proof screws using supplied L-type hex key wrench and

remove the dome cover. Be careful not to scratch the dome cover.

c) You may feed the cables through the upper conduit hole or the side conduit hole.

Please use the supplied blind pug to seal the unused conduit hole.

d) Side conduit hole installation: Disassemble the cable gland first and feed the

network and I/O cable through the sealing nut, claw and cable gland. Connect the

cables to the camera. Attach the cable gland to the conduit hole. Push the claw

into the cable gland and tighten the sealing nut to secure the cables.

5



B. Wall mounting and Ceiling mounting

a) Attached the alignment sticker to the wall. Drill five holes into the wall. Then hammer

the supplied plastic anchors into the screw holes and secure the mounting plate.

b) Attach the camera to the mounting plate and turn the camera clockwise until the clips

snap to the mounting plate.

c) Put the O-rings on the two supplied screws and fix the camera to the mounting plate

from inside with them to prevent unauthorized removal.



C. Connect all cables

C1. Without Power over Ethernet (PoE) connection

1. Connect the power adaptor to the IP Camera.

2. Use a standard RJ-45 network cable and connect the IP Camera to a

hub/switch/router.



C2. Power over Ethernet (PoE)

1. Use a standard RJ-45 network cable and connect the IP Camera to a PoE-enabled

hub/switch/router.



6



D. To adjust the view angle- 3 axis mechanism design

1. Turn the lens module right and left to your desired pan position.

2. Turn the lens module up and down to your desired tilt position.

3. Turn the lens module to adjust the image orientation to satisfied angle.



Important:

Make sure the IR LEDs are not blocked by the housing as it will affect the IR performance.

If the image is upside down, please use the image rotate function in Video Setting.



7



E. Completion

1. Clean the dome bubble to remove the dust and finger print.

2. Fix the tamper-proof screws using supplied hex wrench. Be careful do not

scratch the cover glass.

3. The installation is complete now.



Windows: Go to Zavio Website and download Camera Installation Tool

Please go http://www.zavio.com/softwaredownloads.php download “Camera

Installation Tool”. And follow the installation process to complete the installation.



8



Access the IP Camera using Camera Installation Tool

1. Please check two settings before using Camera Installation Tool.

a. Browser’s Internet Properties →Security→Default Level

b. Browser’s Internet Properties →Privacy →Uncheck Pop-up Blocker

9



2. Click the Camera Installation Tool Icon on your desktop. The main page will show

up listing all active camera and video server devices. Select the desired IP

cameras from the list and click Link to IE.

3. Enter Username and Password to login to the IP Camera.

(Default is admin / admin)



Altri manuali per D8520

Indice

Altri manuali Zavio Telecamera di sicurezza

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente