Zcom ZCN-1523H-5-16 Manuale utente
IEEE 802.11a/n Wireless Outdoor CPE
Quick Installation Guide
V 2.0 July 2010
Copyright
Copyright © 2010 all rights reserved. No part of this publication may be reproduced, adapted,
stored in a retrieval system, translated into any language, or transmitted in any form or by any
means without the written permission of the supplier.
About the Quick
Installation Guide
This Quick Installation Guide is intended to guide professional installer to install the IEEE
802.11a/n Wireless Outdoor CP. It covers procedures to assist you in avoiding unforeseen
problems.
Conventions
This sign indicates a warning or caution that you have to abide.
This sign indicates an important note that you must pay attention to.
Note:
Warning:
Chapter 1 Introduction Page 3
Chapter 1 Introduction
Introduction
The IEEE 802.11a/n Wireless Outdoor CPE is a multi-mode last-mile broadband solution for
customers like wireless ISP (WISPs) and system integrators. By the nature of complying with
the IEEE802.11n standard and featuring high power output, the IEEE 802.11a/n Wireless CPE
supports higher bandwidth of up to 300Mbps with longer range for outdoor applications.
The IEEE 802.11a/n Wireless Outdoor CPE can be used as the access point, the customer
premises equipment (CPE), the WDS or the AP Repeater. While being as the access point, it
can be deployed outdoors to provide outdoor wireless internet service. In the other way to be
as the outdoor CPE, it can receive wireless signal over the last mile, helping WISPs deliver
internet service to the new residential and the business customer where wired broadband
internet service, such as cable and DSL, can not serve in. In addition, the easy-to-install
Wireless Outdoor CPE covers 5GHz bands, which features outstanding throughput
performance and a cost-effective design that allows users to have the reliable outdoor
equipment at the affordable price.
Chapter 2 Preparation before Installation Page 4
Chapter 2 Preparation before Installation
This chapter describes safety precautions and product information you have to know. Please
check this chapter before installing the CPE.
Professional Installation Required
Please seek assistance from a professional installer who is well trained in the RF installation
and knowledgeable in the local regulations.
Safety Precautions
To keep you safe and install the hardware properly, please read and follow these safety
precautions.
1. If you are installing the IEEE 802.11a/n Wireless Outdoor CPE for the first time, for your
safety as well as others’, please seek assistance from a professional installer who has
received safety training on the hazards involved.
2. Keep safety as well as performance in mind when selecting your installation site,
especially where there are electric power and phone lines.
3. When installing the CPE, please note the following things:
♦Do not use a metal ladder;
♦Do not work on a wet or windy day;
♦Wear shoes with rubber soles and heels, rubber gloves, long sleeved shirt or jacket.
4. When the system is operational, avoid standing directly in front of it. Strong RF fields are
present when the transmitter is on.
Chapter 2 Preparation before Installation Page 5
Installation Precautions
To keep the CPE well while you are installing it, please read and follow these installation
precautions.
1. Users MUST use a proper and well-installed surge arrestor with the IEEE 802.11a/n
Wireless Outdoor CPE; otherwise, a random lightening could easily cause fatal damage to
the unit. EMD (Lightning) DAMAGE IS NOT COVERED UNDER WARRNTY.
2. Users MUST use the “Power cord & PoE Injector” shipped in the box with the CPE. Use of
other options will cause damage to the unit.
3. Users MUST power off the CPE first before connecting the external antenna to it. Do not
switch from built-in antenna to the external antenna from WEB management without
physically attaching the external antenna onto the CPE; otherwise, damage might be
caused to the unit itself.
Product Package
The product package you have received should contain the following items. If any of them are
not included or damaged, please contact your local vendor for support.
IEEE 802.11a/n Wireless Outdoor CPE ×1
Pole Mounting Ring ×2
Power Cord & PoE Injector ×1
Product CD ×1
Product CD contains Quick Installation Guide and User Manual!
Note:
Chapter 2 Preparation before Installation Page 6
Pole Mounting Ring
- Power cord & PoE Injector
Users MUST use the “Power cord & PoE Injector” shipped in the box with the CPE
.
Use of other options will cause damage to the unit.
Warning:
Chapter 3 System Installation Page 7
Chapter 3 System Installation
Connect up
1. The bottom of IEEE 802.11a/n wireless outdoor CPE is a movable cover. Loosen the
screw with a Philips screwdriver. Grab the cover and pull it back harder to take it out as
the figure shown below.
2. Plug a standard Ethernet cable into the RJ45 port labeled “LAN 1”. Do not plug the
cable into the RJ45 port labeled “LAN 2”.
Chapter 3 System Installation Page 8
The secondary Ethernet port (labeled LAN 2) is for IP video integration. To use it you
need to enable the secondary port in advance before connecting with the IP camera
from the CPE’s Web Management as shown below.
3. Take out the power cord and PoE injector from the gift box, and plug the power cord into
the DC port of the PoE injector as the below picture shows.
4. Put what in the Step.2 and Step.3 together by plugging the other side of the Ethernet
cable in the Step.2 into the PoE port of the PoE injector in the Step.3. When you finish
the Step.4, the set will be like the following picture:
Chapter 3 System Installation Page 9
5. Press the black PWR button beside the LAN 1 Ethernet port.
6. Attach and fasten the removable cover to the bottom of the unit with the screw.
7. Power on the IEEE 802.11a/n Wireless Outdoor CPE by plugging the power adapter to
the power socket.
Chapter 3 System Installation Page 10
Using the External Antenna
The IEEE 802.11a/n Wireless Outdoor CPE provides two reverse SMA antenna connectors if
you prefer to use the external antenna for your application instead of the built-in directional
antenna, please follow the steps below.
1. Remove the two plugs as circled below:
2. Connect your external antenna to the SMA-type connectors at the bottom of the CPE.
Users MUST power off the CPE first
before connecting the external antenna to
it. Do not switch from built-in antenna to the external antenna from WEB
management without physically attaching the external antenna onto the CPE
;
otherwise, damage might be caused to the unit itself.
Follow the steps described in Connect Up to finish the installation.
Warning:
Indice
Manuali Hardware di rete popolari di altre marche
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuale utente
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuale utente
Yudor
Yudor YDS-16 Manuale utente
D-Link
D-Link ShareCenter DNS-320L Manuale utente
Samsung
Samsung ES1642dc Istruzioni per l’uso
Honeywell Home
Honeywell Home LTEM-PV Istruzioni per il montaggio
