Zcom AG-623G2 Manuale utente

Z-Com AG-623G2

IEEE 802.11 a/b/g

Wireless Network Mini PCI

User’s Manual

V1.0 January 2010

Page 2

FCC Statement

Warning: Changes or modifications to this unit not expressly approved by the party

responsible for compliance could void the user authority to operate the equipment.

For product available in the USA/Canada market, only channel 1~11 can be operated.

Selection of other channels is not possible. This device is going to be operated in

5.15~5.25GHz frequency range, it is restricted in indoor environment only.

The device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation. The

user’s manual or instruction manual for an intentional or unintentional radiator shall caution the

user that changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment. NOTE: This equipment

has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures: Reorient or relocate the receiving antenna. Increase the

separation between the equipment and receiver. Connect the equipment into an outlet on a

circuit different from that to which the receiver is needed. Consult the dealer or an experienced

radio/TV technician for help.

Page 3

CAUTION:

To comply with FCC RF exposure compliance requirements, a separation distance of at least

20 cm must be maintained between the antenna of this device and all persons. This

Transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter This device is intended only for OEM integrators under the following conditions:

The antenna must be installed such that 20 cm is maintained between the antenna and users.

For laptop installations, the antenna must be installed to ensure that the proper spacing is

maintained in the event the users places the device in their lap during use (i.e. positioning of

antennas must be placed in the upper portion of the LCD panel only to ensure 20 cm will be

maintained if the user places the device in their lap for use) and The transmitter module may

not be co-located with any other transmitter or antenna. As long as the 2 conditions above are

met, further transmitter testing will not be required. However, the OEM integrator is still

responsible for testing their end-product for any additional compliance requirements required

with this module installed (for example, digital device emissions, PC peripheral requirements,

etc.).

LABEL OF THE END PRODUCT:

The final end product must be labeled in a visible area with the following " Contains TX FCC ID:

M4Y-AG623G2 ". If the size of the end product is larger than 8x10cm, then the following FCC

part 15.19 statement has to also be available on the label: This device complies with Part 15

of FCC rules. Operation is subject to the following two conditions: (1) this device may not

cause harmful interference and (2) this device must accept any interference received,

including interference that may cause undesired operation.

FCC NOTICE: To comply with FCC part 15 rules in the United States, the system must be

professionally installed to ensure compliance with the Part 15 certification. It is the

responsibility of the operator and professional installer to ensure that only certified systems

are deployed in the United States. The use of the system in any other combination (such as

co-located antennas transmitting the same information) is expressly forbidden.

Page 4

IC Statement :

This Class B digital apparatus complies with Canadian ICES-003.

Operation is subject to the following two conditions: (1) this device may not cause interference,

and (2) this device must accept any interference, including interference that may cause

undesired operation of the device.

Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.

For product available in the USA/Canada market, only channel 1~11 can be operated.

Selection of other channels is not possible.

This device and its antenna(s) must not be co-located or operation in conjunction with any

other antenna or transmitter.

To reduce potential radio interference to other users, the antenna type and its gain should be

so chosen that the equivalent isotropically radiated power (e.i.r.p) is not more than that

permitted for successful communication.

The device could automatically discontinue transmission in case of absence of information to

transmit, or operational failure. Note that this is not intended to prohibit transmission of control

or signaling information or the use of repetitive codes where required by the technology.

The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for

harmful interference to co-channel mobile satellite systems.

The maximum antenna gain permitted (for devices in the band 5725-5825 MHz) to comply with

the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate, as

stated in section A9.2(3).

Page 5

IMPORTANT NOTE:

IC Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with minimum

distance 20cm between the radiator & your body.

This module is intended for OEM integrator. The OEM integrator is still responsible for the IC

compliance requirement of the end product, which integrates this module.

20cm minimum distance has to be able to be maintained between the antenna and the users

for the host this module is integrated into. Under such configuration, the IC RSS-102 radiation

exposure limits set forth for an population/uncontrolled environment can be satisfied.

Any changes or modifications not expressly approved by the manufacturer could void the

user's authority to operate this equipment.

USERS MANUAL OF THE END PRODUCT:

In the users manual of the end product, the end user has to be informed to keep at least 20cm

separation with the antenna while this end product is installed and operated. The end user has

to be informed that the IC radio-frequency exposure guidelines for an uncontrolled

environment can be satisfied. The end user has to also be informed that any changes or

modifications not expressly approved by the manufacturer could void the user's authority to

operate this equipment. IC statement is required to be available in the users manual: This

Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

LABEL OF THE END PRODUCT:

The final end product must be labeled in a visible area with the following " Contains TX IC :

3195A-AG623G2”.

Page 6

1. Introduction

54Mbps IEEE802.11a/b/g Wireless Network Mini PCI Adapter is the perfect solution for

your wireless network applications based on the IEEE 802.11a/b/g standard offering a

data rate of 54Mbps in a wireless LAN environment. AG-623G2 is designed for Access

Point, Router, ATUR, Printer Server series, IP Camera series and Internet Video Server

gives you wireless access the web and network resource without the wire. AG-623G2

provides high-speed access to network resources and has built-in 40/64-bit, 128 bit and

256 bit of WEP (Wired Equivalent Privacy) data encryption. With Direct Spread Spectrum

Signaling (DSSS) and Orthogonal Frequency Division Multiplexing (OFDM), domain

access control, WEP encryption and group security, the modules will safeguard all your

wireless data transmissions from your nosy neighbors. AG-623G2 allows you to take full

advantage of your devices mobility with access to real-time information and online

services anytime and anywhere.

2. Features

1. Complies with IEEE 802.11a/b/g Standard for Wireless LAN.

2. Works withAll Existing Network Infrastructures.

3. Compatible with Wi-Fi Wireless Products and Services.

4. Capable of up to 256-Bit WEP Encryption.

5. Freedom to Roam While staying Connected.

6. Delivers data rate up to 54 Mbps in G mode and up to 108 Mbps in Turbo AG mode.

7. Two UF-L Connectors for External Antenna.

8. Support Antenna diversity for Better Sensitivity.

9. Lower Power Consumption.

Page 7

3. Hardware Installation

The following sections in this chapter describe how to install AG-623G2 Module

3.1. Installation Overview

AG-623G2 wireless module is design for Access Point, Router, ATU-R, Printer Server

series, IP Camera series and Internet Video Server only.

3.2. Safety Recommendations

The safety guidelines are as follows:

Keep the board area clear and dust-free before, during, and after installation.

Keep tools away from walk areas where you and others could fall over them.

Do not wear loose clothing or jewelry, such as earrings, bracelets, or chains that

could get caught in the board.

Wear safety glasses if you are working under any conditions that might be hazardous

to your eyes.

Do not perform any action that creates a potential hazard to people or makes the

equipment unsafe.

Never attempt to lift an object that is too heavy for one person to handle.

3.3. Maintaining Safety with Electricity Warning:

Before working on a board or working near power supplies, unplug the power cord on AC

units; on DC units, disconnect the power at the circuit breaker. Follow these guidelines

when working on equipment powered by electricity:

Do not work alone if potentially hazardous conditions exist anywhere in your work

space.

Never assume that power is disconnected from a circuit; always check the circuit,

extension cables, frayed power cords, and missing safety grounds.

If an electrical accident occurs, proceed as follows: – Use caution; do not become a

victim yourself. – Disconnect power from the system. – If possible, send another

Page 8

person to get medical aid. Otherwise, assess the condition of the victim and then call

for help. – Determine if the person needs rescue breathing or external cardiac

compressions; then take appropriate action.

3.4. Installing a AG-623G2

1. Remove the AG-623G2 module from its protective packaging.

2. Avoiding Electrostatic Discharge. Before you install the AG-623G2 module, ground

yourself by touching a piece of metal to avoid electrostatic discharge (ESD). You should

also take the following precautions to prevent damage to the AG-623G2 module:

Keep the AG-623G2 module in its antistatic-shielded bag until you are ready to install

it.

Handle the AG-623G2 module by its edges.

Ensure the connector is connected to above Model’s board tightly.

Indice

Altri manuali Zcom Router wireless

Zcom

Zcom XG-2000 Manuale utente

Manuali Router wireless popolari di altre marche

Milesight

Milesight UG67 Manuale utente

Airlogic

Airlogic AirSync Class 1 Manuale del proprietario

Samsung

Samsung WCH730B Manuale utente

TELEFONICA

TELEFONICA USB Adapter Manuale utente

NETGEAR

NETGEAR PowerLINE WiFi 1000 Series Manuale utente

Askey

Askey RAC2V1K Manuale utente

Alloy

Alloy WLF2454AP-S Manuale utente

TP-Link

TP-Link TL-WR542G Manuale utente

NETGEAR

NETGEAR WNR2000v4 Manuale utente

Hama

Hama 53120 Manuale utente

Intellinet

Intellinet 524582 Manuale utente

Asus

Asus RT-N10P Manuale utente

D-Link

D-Link DIR-506L Manuale utente

Sapido

Sapido GR297n Manuale utente

Asus

Asus DSL-N55U Manuale utente

AMTC

AMTC WR7502 Manuale utente

Compaq

Compaq CP-2W - iPAQ Connection Point Manuale utente

SMC Networks

SMC Networks WBR14-N2 FICHE Manuale utente