Zephyr Essentials Modena ZMO-E30AS Guida all'installazione

Use, Care, and Installation Guide

www.zephyronline.com

Model number:

Serial Number:

MAY11.0201 © Zephyr Corporation

Modena Wall

ZMO-E30AS

ZMO-M90AS

www.zephyronline.com

SAFETY NOTICE ................................................................. 2-3

LIST OF MATERIALS....................................................... 4

INSTALLATION

Ducting Calculation Sheet....................................... 5

Mounting Height & Clearance................................ 6

Ducting Options ........................................................... 7

Hood Speciﬁcations ................................................... 8

Mounting the Range Hood...................................... 9

Ductless Recirculating .............................................. 10

FEATURES & CONTROLS

Touch Controls ............................................................. 11

User Interface............................................................... 12

MAINTENANCE

Hood and Filter Cleaning......................................... 13

TROUBLESHOOTING................................................................ 14

WIRING & FAN CURVE DIAGRAMS .................................. 15

LIST OF PARTS AND ACCESSORIES .............................. 16

Table of Contents

Important Safety Notice

READ AND SAVE THESE INSTRUCTIONS

www.zephyronline.com

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE.

WARNING

TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

a. Use this unit only in the manner intended by the manufacturer, if you have questions, contact the manufacturer.

b. Before servicing or cleaning unit, switch power off at service panel and lock panel to prevent power from being switched on accidentally.

When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service

panel.

CAUTION

For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. Take care when using cleaning

agents or detergents. Suitable for use in household cooking area.

WARNING

TO REDUCE THE RISK OF RANGE TOP GREASE FIRE:

a. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly

on low or medium settings.

b. Always turn hood ON when cooking at high heat or when ﬂaming food

c. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or ﬁlter.

d. Use proper pan size. Always use cookware appropriate for the size of the surface element.

e. Keep fan, ﬁlters and grease laden surfaces clean.

f. Use high setting on hood only when necessary.

g. Don’t leave hood unattended when cooking.

h. Always use cookware and utensils appropriate for the type of and amount of food being prepared.

WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP FIRE, OBSERVE THE FOLLOWING:

a. SMOTHER FLAMES with a close-ﬁtting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS.

If the ﬂames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.

b. NEVER PICK UP A FLAMING PAN – You may be burned.

c. DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.

d. Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate it.

2. The ﬁre is small and contained in the area where it started.

3. The ﬁre department is being called.

4. You can ﬁght the ﬁre with your back to an exit

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

a. Installation work and electrical wiring must be done by qualiﬁed person(s) in accordance with all applicable codes and standards.

Including ﬁre-rated construction.

b. Sufﬁcient air is needed for power combustion and exhausting of gases through the ﬂue (chimney) of fuel burning equipment to prevent

back-drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National

Fire Protection Association (NFPA) and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and

the local code authorities.

c. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

d. Ducted fans must always vent to the outdoors.

e. NEVER place a switch where it can be reached from a tub or shower.

f. Make sure the power is off before installing, wiring or maintenancing.

Important Safety Notice

WARNING

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

CAUTION

To reduce risk of ﬁre and to properly exhaust air outside - Do not vent exhaust air into spaces within walls, ceilings,

attics, crawl spaces or garages.

OPERATION

Always leave safety grilles and ﬁlters in place. Without these components, operating blowers could catch onto hair, ﬁngers

and loose clothing.

The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation,

maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due to

negligence and the warranty of the unit automatically expires due to improper maintenance.

*NOTE: Please check www.zephyronline.com for revisions before doing any custom work.

ELECTRICAL REQUIREMENTS

Important:

Observe all governing codes and ordinances.

It is the customer’s responsibility:

- To contact a qualiﬁed electrical installer.

- To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70

latest edition* or CSA standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and

all local codes and ordinances.

If codes permit and a separate ground wire is used, it is recommended that a qualiﬁed electrician determine that the

ground path is adequate.

Do not ground to a gas pipe.

Check with a qualiﬁed electrician if you are not sure the range hood is properly grounded.

Do not have a fuse in the neutral or ground circuit.

*National Fire Protection Association Batterymarch Park, Quincy, Massachusetts 02269

** CSA International 8501 East Pleasant Valley Road, Cleveland, Ohio 44131-5575

This appliance requires a 120V 60Hz electrical supply and connected to an individual properly grounded branch circuit

protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire with ground. Please also refer to

Electrical Diagram on product.

A cable locking connector (not supplied) might also be required by local codes. Check with local requirements, purchase

and install appropriate connector if necessary.

ZMO-E30AS & ZMO-M90AS - 215 Watts, 3.5 Amps

List of Materials

www.zephyronline.com

Wire Nuts (3)

M6 x 1-1/2” (3) M6 x 1” (2)

M3.5 x 8 (2)

PARTS NOT SUPPLIED

- Ducting, conduit and all installation tools

- Cable connector (if required by local codes)

- Duct cover extension accessory

- Recirculating kit accessory

HARDWARE PACKAGE CONTENTS

MODELS: ZMO-E30AS, ZMO-M90AS

PARTS SUPPLIED

1 - Hood with internal blower

1- Aluminum mesh filter

1 - Duct cover assembly (top and bottom)

1 - Duct cover wall bracket

4 - 3W LED light bulbs

1 - 8” round backdraft damper (pre-installed)

1 - Hardware package

ø12 OD / ø5 ID (1)

Washer

3/16 x 3/8 (2)

Duct pieces To t a l

Equivalent number

length x used =

3-1/ 4” x 10”

Rect.,

straight

1 Ft. x ( ) = Ft.

8” Round,

straight

1 Ft. x ( ) = Ft.

3-1/ 4” x 10”

Rect.900

elbow

15 Ft. x ( ) = Ft.

3-1/ 4” x 10”

Rect.450

elbow

9 Ft. x ( ) = Ft.

3-1/ 4” x 10”

Rect.900

flat elbow

24 Ft. x ( ) = Ft.

3-1/ 4” x 10”

Rect.

wall cap

with damper

30 Ft. x ( ) = Ft.

3-1/ 4” x 10”

Rect.to

6” round

transition

5 Ft. x ( ) = Ft.

3-1/ 4” x 10”

Rect.to

6” round

transition

900 elbow

20 Ft. x ( ) = Ft.

8” Round,

900 elbow

15 Ft. x ( ) = Ft.

8” Round,

450 elbow

9 Ft. x ( ) = Ft.

Ft.

7” Round,

straight

1 Ft. x ( ) = Ft.

Subtotal column 1 =

Duct pieces To t a l

Equivalent number

length x used =

6”- 8”Round

wall cap

with damper

30 Ft. x ( ) = Ft.

Round

wall cap

with damper

30 Ft. x ( ) = Ft.

7” or 8”

Round,

900elbow

15 Ft. x ( ) = Ft.

7” or 8”

Round,

450

elbow

9 Ft. x ( ) = Ft.

Ft.

6”- 8” Round,

roof cap

30 Ft. x ( ) = Ft.

7” or 8”

Round,

roof cap

30 Ft. x ( ) = Ft.

Subtotal column 2 =

Subtotal column 1 =

Total ductwork =

Maximum Duct Length: For satisfactory air movement,

the total duct lengthshould not exceed 100 equivalent feet.

6” round to

3-1/ 4” x 10”

rect.

transition

1 Ft. x ( ) = Ft.

6” round to

3-1/ 4” x 10”

rect.

transition

900 elbow

16 Ft. x ( ) = Ft.

7” round to

3 1/ 4” x 10”

rect.

transition

8 Ft. x ( ) = Ft.

7” round to

3-1/ 4” x 10”

rect.

transition

900 elbow

23 Ft. x ( ) = Ft.

Installation – Ducting Calculation Sheet

Installation – Mounting Height & Clearance

www.zephyronline.com

DUCTING

A minimum of 8” round duct is recommended to

maintain maximum air ﬂow efﬁciency.

Always use rigid type metal ducts only. Flexible

ducts could restrict air ﬂow by up to 50%.

Use calculation worksheet to compute total duct

work (Page 5).

ALWAYS, when possible, reduce the number of

transitions and turns. If a long duct run is required,

increase duct size from 8” to 10”.

If turns or transitions are required: Install as far

away from duct opening and as far apart between

the two transitions as possible.

Minimum mount height between range top to hood

bottom should be no less than 26”.

Maximum mount height should be no higher than

34”.

It is important to install the hood at the proper

mounting height. Hoods mounted too low could

result in heat damage and ﬁre hazard; while hoods

mounted too high will be hard to reach and will

loose its performance and efﬁciency.

If available, also refer to range manufacturer’s

height clearance requirements and recommended

hood mounting height above range. Always check

your local codes for any differences.

Duct cover extension kit available for ceiling

heights up to 12 feet. Turn to page 16 for part

number and ordering information.

DAMAGE-SHIPMENT / INSTALLATION:

• Please fully inspect unit for damage before

installation.

• If the unit is damaged in shipment, return the

unit to the store in which it was bought for

repair or replacement.

• If the unit is damaged by the customer, repair

or replacement is the responsibility of the

customer.

• If the unit is damaged by the installer (if other

than the customer), repair of replacement must

be made by arrangement between customer

and installer.

26” min.

34” max.

min. A

min. B

max. C

min. D

min. E

max. F

Standard Extension

Hood Heights Duct Cover Duct Cover

minimum ducted (A) 27” 41-1/2“

minimum recirculating (B) 31” 45-1/2“

maximum (C) 50” 80”

Ceiling Heights

minimum ducted (D) 89” (7’ 5”) 103-1/2“ (8‘ 7-1/2”)

minimum recirculating (E) 93” (7’ 9”) 107-1/2“ (8‘ 11-1/2”)

maximum (F) 120” (10’ ) 150” (12’ 6”)

36”

WARNING FIRE HAZARD

NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages.

All exhaust must be ducted to the outside, unless using the recirculating option.

Use single wall rigid Metal ductwork only.

Fasten all connections with sheet metal screws and tape all joints w/ certiﬁed Silver Tape or Duct Tape.

Some Ducting Options

Installation – Ducting Options

side wall cap

w/ gravity damper

Soffit or crawl space

Roof Pitch w/

Flashing & Cap

ductless

recirculating

side wall cap

w/ gravity damper

(blower

housing)

(blower

housing)

(blower

housing)

(blower

housing)

www.zephyronline.com

Installation – Hood Speciﬁcations

side of hood

front of hood

top of hood

7 15/16”

4 5/8”

5 1/16”

AC In

13 3/8”

29 15/16”, 35 7/16”

6 5/16”

16 15/16”

8 3/8”

STANDARD

min. ducted - 27”

min. recirc. - 31”

max. - 50”

Z1C-00MO

min. ducted - 41 1/2”

min. recirc. - 45 1/2”

max. - 80”

12 3/8”

22 1/8”

1 3/16”

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Zephyr Essentials Cappa di ventilazione

Zephyr Essentials

Zephyr Essentials Twister AK8000BS Guida all'installazione

Zephyr Essentials

Zephyr Essentials ZAN-E30CBS Guida all'installazione

Zephyr Essentials

Zephyr Essentials Europa Savona Series Guida all'installazione

Zephyr Essentials

Zephyr Essentials Power Vortex ES Series Guida all'installazione

Zephyr Essentials

Zephyr Essentials Siena Pro ZSP-E48AS Guida all'installazione

Zephyr Essentials

Zephyr Essentials Roma Wall ZRO-E30CS Guida all'installazione

Zephyr Essentials

Zephyr Essentials Verona Island Guida all'installazione

Zephyr Essentials

Zephyr Essentials Anzio Island ZAZ-M90CS Guida all'installazione

Zephyr Essentials

Zephyr Essentials Siena ZSI-E30AS Guida all'installazione

Zephyr Essentials

Zephyr Essentials Siena Pro Island Guida all'installazione

Zephyr Essentials

Zephyr Essentials Modena Island ZMD-M90AS Guida all'installazione

Zephyr Essentials

Zephyr Essentials Genova ZGE-E30AS Guida all'installazione

Zephyr Essentials

Zephyr Essentials Spruce AK9834AS Guida all'installazione

Zephyr Essentials

Zephyr Essentials Twister AK8000AS-ES Guida all'installazione

Zephyr Essentials

Zephyr Essentials Milano Wall Guida all'installazione

Zephyr Essentials

Zephyr Essentials Breeze I AK1100 Series Guida all'installazione

Zephyr Essentials

Zephyr Essentials ZAN-E30CS Guida all'installazione

Zephyr Essentials

Zephyr Essentials Tornado Mini AK8400AS Guida all'installazione

Zephyr Essentials

Zephyr Essentials Vortex AK9034AS-ES Guida all'installazione

Zephyr Essentials

Zephyr Essentials Breeze I Guida all'installazione

Zephyr Essentials

Zephyr Essentials Venezia Series Manuale utente

Zephyr Essentials

Zephyr Essentials Ravenna ZRV-E30AGC Guida all'installazione

Zephyr Essentials

Zephyr Essentials Pyramid ZPY-E30AB Guida all'installazione

Zephyr Essentials

Zephyr Essentials Monsoon Mini Guida all'installazione

Manuali Cappa di ventilazione popolari di altre marche

emmeti

emmeti RECUPA MED A-140 Guida

Nibe

Nibe F135 Manuale utente

Kuppersberg

Kuppersberg INTRO 60 Istruzioni di installazione e manutenzione

Zephyr

Zephyr Spruce AK9834BS Guida all'installazione

Hisense

Hisense MH6INBG Manuale utente

Miele

Miele DA 1255 Manuale utente

Broan

Broan 46000 Manuale utente

GE Profile PV977 Istruzioni originali

FALMEC

FALMEC FFRIA24W5FS Manuale utente

Whirlpool

Whirlpool RH2600XL-1 SERIES Manuale utente

Küppersbusch

Küppersbusch DX ISLA Manuale utente

ETNA

ETNA AV360RVS Manuale utente

JUNO

JUNO JDF603E6 Manuale utente

Miele

Miele DA 6708 D Manuale utente

Tricity Bendix

Tricity Bendix LE 150 Manuale

AEG

AEG X68163BV1 Manuale utente

AEG

AEG 125 D Manuale utente

Smeg

Smeg KSEV97X Manuale utente