Zhejiang NVR300 Series Manuale utente

NVR300 Series

Network Video Recorders

Quick Guide

Manual Version: P102-20140526

No part of this manual may be reproduced or transmitted in any form or

by any means without prior written consent of Zhejiang Uniview

Technologies Co., Ltd.

Notice

The information in this manual is subject to change without notice.

Every effort has been made in the preparation of this manual to ensure

accuracy of the contents, but all statements, information, and

recommendations in this manual do not constitute the warranty of any

kind, express or implied.

Environmental Protection

This product has been designed to comply with the requirements on

environmental protection. For the proper storage, use and disposal of

this product, national laws and regulations must be observed.

Preface

Audience

This manual is intended for:

Surveillance system planners

Field technical support and servicing engineers

Software installation, configuration, and servicing administrators

Product users

Precautions

If this equipment is used in a domestic environment, radio

disturbance may arise. When such trouble occurs, you might be

required to take corrective actions.

Do not remove the dismantlement-preventive seal from the chassis

cover of the device without permission. If you want to open the

chassis, contact the local agent of our company for help. Otherwise,

we shall not be held liable for any consequence caused thereby.

Make sure the device is sturdy and well grounded and meets heat

dissipation and lightning protection requirements. Avoid vibration

when using the device.

Provide a stable and compliant power supply before powering on

the device.

Before performing the verification (refer to section “Check Before

Power-On”), make sure that the power is disconnected, for fear of

bodily injury or equipment damage caused by incorrect cable

connection.

Power interruption may cause hard disk damage or abnormal

functions. To shut down the device, strictly follow the instructions.

If power interruption often occurs, configure an uninterrupted

power supply (UPS).

Safety and Compliance Information

Conventions Used Symbol

The symbols in this chapter are shown in the following table. They are

used to remind the reader of the safety precautions during equipment

installation and maintenance.

Safety

Symbol

Description

Generic alarm symbol: To suggest a general safety concern.

ESD protection symbol: To suggest electrostatic-sensitive

equipment.

Electric shock symbol: To suggest a danger of high voltage.

Safety Information

WARNING!

Installation and removal of the unit and its accessories must be carried

out by qualified personnel. You must read all of the Safety Instructions

supplied with your equipment before installation and operation.

Warnings:

If the product does not work properly, please contact your dealer

or the nearest service center. (We shall not assume any

responsibility for problems caused by unauthorized repair or

maintenance.)

To reduce the risk of fire or electrical shock, do not expose this

product to rain or moisture.

This installation should be made by a qualified service person and

should conform to all the local codes.

Please install blackouts equipment into the power supply circuit for

convenient supply interruption.

The separate earthing terminal must be permanently connected to

earth.

For AC supplied model: The plug-socket combination must be

accessible at all times as it serves as the main disconnecting device.

Before the power cable is installed or removed, the power must be

turned off.

To avoid heat accumulation, good ventilation is required for a

proper operating environment.

Improper use or replacement of the battery may result in hazard of

explosion. Please use the manufacturer recommended battery

type.

Caution: Fiber optic ports –optical safety.

Never look at the transmit laser while the power is on. Never look

directly at the fiber ports and the fiber cable ends when they are

powered on.

Caution: Use of controls or adjustments to the performance or

procedures other than those specified herein may result in hazardous

laser emissions.

Regulatory Compliance

FCC Part 15

This equipment has been tested and found to comply with the limits for

digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the instruction manual, may

cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in

which case the user will be required to correct the interference at his

own expense.

This product complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including

interference that may cause undesired operation.

LVD/EMC Directive

This product complies with the European Low Voltage Directive

2006/95/EC and EMC Directive 2004/108/EC.

WEEE Directive–2002/96/EC

The product this manual refers to is covered by the Waste Electrical &

Electronic Equipment (WEEE) Directive and must be disposed of in a

responsible manner.

Contents

1 Overview..............................................................................................1

2 Mounting .............................................................................................1

Installation Check..........................................................................................1

Installing Hard Disks......................................................................................1

NVR308-48/24/32/16-IN ......................................................................1

NVR308-32L/16L/09L-IN.......................................................................5

Installing the Equipment ...............................................................................9

Mounting to the Workbench..............................................................10

Mounting into a Cabinet.....................................................................10

3 Appearance........................................................................................11

Front View...................................................................................................11

Indicators ....................................................................................................11

Panel buttons..............................................................................................13

Rear View ....................................................................................................16

Interfaces ....................................................................................................17

4 Connecting Cables ..............................................................................19

Connecting to Alarm Input/Output Device .................................................19

Connecting to a Third-Party Device ............................................................21

RS485 Serial Cables.............................................................................21

Connecting to a third-party device via RS485 interface .....................21

Connecting using an audio/video cable ......................................................23

Connecting RS232 Serial And Network Cables............................................24

Connecting a GroundCable .........................................................................25

Connecting a Power Cable ..........................................................................26

5 Switching On/Off the Device ...............................................................26

Check Before Power-On..............................................................................26

Turning on the Device.................................................................................26

Soft Off........................................................................................................26

Soft Off Using the POWER ON/OFF Button ........................................27

Soft Off Through Man-Machine Interface ..........................................27

Soft Off Through Web Interface .........................................................27

6 Common Configurations .....................................................................27

Man-Machine Interface ..............................................................................27

About the Interface ............................................................................27

Menu Structure ..................................................................................28

Initial Configuration ....................................................................................28

Quickly Adding IPC ......................................................................................35

Preview .......................................................................................................38

Pane Toolbar on the Preview Interface ..............................................38

Preview Status ....................................................................................39

Right-click Context Menu ...................................................................40

Recording ....................................................................................................41

Playback ......................................................................................................42

Backup.........................................................................................................42

Prerequisites.......................................................................................42

Procedure ...........................................................................................43

Web Interface .............................................................................................45

7 Specifications .....................................................................................46

8 HDD Storage Calculation Chart............................................................47

1 Overview

As our new-generation network video recorders, the NVR300 series

incorporates a wide range of features such as audio and video

decoding, data transmission, and storage, and provides a rich set of

input and output interfaces to meet various business needs.

The NVR300 can connect to coding devices such as IP cameras (IPCs) to

form a separate network or to a central server platform for central

networking to support a diverse range of video surveillance

applications.

2 Mounting

Installation Check

Open the packing box and check the equipment model, accessory

types and quantities to ensure all the components are available. For

equipment model, accessory types and quantities, please refer to the

packing list.

Installing Hard Disks

For supported hard disk types, consult our authorized sales or technical

support staff. The following examples illustrate how to install hard disks

on a workbench. The installation process may varies according to

conditions.

The following tools are required for installation: flat-head and Phillips

screwdrivers.

NVR308-48/24/32/16-IN

The hard drive interface is located inside the device. You need to

remove the front panel to install the hard disk. The hard disks are

hot-swappable and support mixed insertion. The disks can be powered

on in order to minimize the impulse current produced during the

power-on process.

WARNING!

The hard disk can be hot-plugged only when no data is read

or written. The indicator of hard disk is not blinking when no data is

processed.

Wear anti-static gloves when installing a hard disk.

Insert hard disks into the slots of a running device at an interval of

at least six seconds.

Install a hard disk into the NVR308-48/24-IN as follows:

1. Fix the hard disk with screws to the handle bar on the correct

side.

2. Press the buckles on both sides of the front panel and remove the

panel. Note that the front panel is connected to the device body

through an adapter cable and safety rope. Turn over the removed

front panel and place it on the chassis.

Indice

Altri manuali Zhejiang Hardware di rete

Zhejiang

Zhejiang NVR200 series Manuale utente

Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor

Yudor YDS-16 Manuale utente

D-Link

D-Link ShareCenter DNS-320L Manuale utente

Samsung

Samsung ES1642dc Istruzioni per l’uso

Honeywell Home

Honeywell Home LTEM-PV Istruzioni per il montaggio

evertz

evertz 7700 Series Manuale utente

D-Link

D-Link ShareCenter DNS-343 Manuale utente

Asante

Asante AsanteBridge 1012 Manuale utente

FireBrick

FireBrick FB2700 Manuale utente

Audiovox Electronics

Audiovox Electronics ARWH2T Manuale utente

ADC

ADC DSX-1 Manuale

NetComm

NetComm NF2 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 5620 Manuale utente

Dell EMC

Dell EMC XC6420 Series Manuale utente

Lanner

Lanner NCA-1020A Manuale utente

Allied Telesis

Allied Telesis AT-TN121-A Manuale utente

Arista

Arista CCA-ETM-Q12 Manuale utente