Zip HydroTap Manuale utente
Your Zip HydroTap will notify you when the filter replacement is due. The change filter light will flash white once per
minute until the filter has been replaced, and the filter percentage will show 0% on the Home screen.
Step 1:
Grab an empty bucket or container to collect the water which will be flushed through the system and an old towel to
mop up any spills.
Step 2:
Open the filter access door on the front of the HydroTap Command Centre. You will see the filter cartridge in front of
you.
Step 3:
Reach to the rear right hand side of the cartridge and you’ll find a flush line (looks like a hose) which is around 60cm
long which will be sealed with a stop cock located in the centre of the hose. Place the free end of the flush
line into the empty bucket or container. Turn the stop cock quickly on then off to relieve system pressure.
Step 4:
Gently hold the filter cartridge then press the red lever at the top right of the unit and rotate the cartridge a quarter
turn to the left. The unit should detach and you should be able to pull it free in a downwards motion. Some water
may drip from the cartridge at this point. Be sure to keep the cartridge level to avoid spills
Step 5:
Place spent cartridge in the sink or other suitable container.
Step 6:
Unpack your replacement cartridge and remove the sanitary cap. Write today’s date where shown on the label.
Ensure you avoid touching the O-rings or filter opening as this can cause bacterial contamination of the cartridge.
Step 7:
Slightly moisten the O-rings with regular tap water and line up the front cartridge label to the left.
Step 8:
Gently but firmly push the cartridge up into the filter head and turn a quarter-turn to the right –as far as it will go
without forcing it. The cartridge should now be locked in position with the front label facing forward.
Step 9:
Press the [MENU] button to bring up the main menu on the screen.
Step 10:
Press the [Install] button and turn the stop valve ON by rotating the lever clockwise until it is in line with the hose
Step 11:
Press the [Filter Flush] button then press [Start] to begin the process. Ensure you run at least 10-litres of water
through to flush the filter of excess black carbon particles.
Step 12:
When the filter flush is finished, turn the stock valve OFF by rotating the lever anti-clockwise until it
is perpendicular to the hose.
Step 13:
Press [Stop] to end the filter flush process.
Step 14:
Press the [Home] button to return to the home screen.
Note: If you are carrying out this flush after the HydroTap’s initial installation, the unit will go directly into calibration
mode after the Filter Flush Mode is turned off. With any subsequent filter changes the system will automatically revert to
the main menu.
Step 15:
Dispose of used cartridge and packaging thoughtfully.
Altri manuali per HydroTap
1
Altri manuali Zip Sistema di filtraggio dell'acqua
Zip
Zip ChillTap Extra Manuale utente
Zip
Zip HydroTap G4 Manuale utente
Zip
Zip ZIP-B Manuale utente
Zip
Zip Elite HydroTap G4 range Manuale utente
Zip
Zip HydroTap G4 Manuale utente
Zip
Zip HydroTap G4 Manuale utente
Zip
Zip ChillTap CT1/140 Manuale utente
Zip
Zip 82341 Manuale utente
Zip
Zip HydroTap G4 Manuale utente
Zip
Zip HydroTap G4 Manuale utente
Zip
Zip HydroTap G4 Manuale utente
Zip
Zip HydroTap series Manuale utente
Zip
Zip HydroTap G5 Touch-Free Wave Manuale di istruzioni
Zip
Zip 803828 Manuale
Zip
Zip FL104 Manuale utente
Zip
Zip HydroTap G5 Touch-Free Wave Manuale di istruzioni
Zip
Zip Commercial HydroTap 86682 Manuale utente
Zip
Zip HydroTap G5 Touch-Free Wave Manuale di istruzioni
