Zippity Baskenridge Guida rapida
Check Box for These Contents
In the event of missing or defective parts please call our customer service department at
1 877 234 6196
(Mon. to Fri. 8:00 AM to 4:00 PM EST).
1.
Post Caps
(4)
2. Top & Bottom Rails
(
4) - 1½” x 1½“ x 41 7/8”
3.
Posts
(4) - 7/8“ x 1½” x 44”
4. Spindles (20) ¼” x 1½” x 31 ¼“
5.
Joiner Clips
(4)
6.
3/4”Self-Auguring Stainless Steel Screw
(16) (Bag A)
7.
1”Self-Tapping Stainless Steel Screw
(8) (Bag B)
8.
End Caps
(8) (4 are installed,4 are loose)
Tools You Will Need
• Cordless Drill
• Level
• Hammer
General Information
• Read Instructions through carefully before beginning assembly.
• When assembling components, place on a non-abrasive surface
(i.e.shipping box) to avoid scratching.
• We recommend an area approx 5’x 8’ for unobstructed assembling.
• You should not need to use excessive force when assembling components.
Baskenridge Vinyl Fence Kit
(42”W x 36”H)
Please read through before starting assembly.
ASSEMBLY INSTRUCTIONS
1
IMPORTANT: CHECK THE INSIDE OF THE LARGER PIECES IN YOUR BOX FOR OTHER MATERIALS
PACKED INSIDE.
Ver 1.0/122718
1
3
2
4
Ground
6
Not to Scale
5
THIS FENCE IS DESIGNED
FOR SEMI-PERMANENT
APPLICATIONS
8 1/2 in
42 in
36 in
1 1/8 in
1 in
36 3/4 in
38 1/4 in
31 1/2 in
2 1/4 in
7
8
2
Pressure fit an end cap to the end of the horizontal rails.
There will be a total of four end caps and four rails.
Slide the top rail up from the bottom of a post until the
pre-drilled hole on the rail aligns with the pre-drilled hole
at the top of the post.
Tip!
Shine an LED light from a smart phone or flashlight down
the end of the posts to help identify alignment of
pre-drilled holes if necessary.
Do the same with the other post.
Secure the rail to both sides of the posts using 3/4” screws
as illustrated.
1
2
STEP ONE
Baskenridge Vinyl Fence Instructions
1
Note: Align Holes
Note: Orientate the bottom of Posts as Illustrated
x4
3
4
4
2 & 3
Note: Spindle holes facing down
STEP TWO
Insert the spindles into the routed holes as illustrated.
Note: the tabs on the end of the spindles are intended to go
into the rail to lock spindles into place.
Push the posts and spindles down into the bottom rail as
illustrated.
1
3
Baskenridge Vinyl Fence Instructions
Note: Once inserted, the
spindles will lock into place.
To remove the spindle(s),
gently insert a butter knife
along the picket direction
as shown and slowly pull up
the spindle(s).
2
2
1
3
4Baskenridge Vinyl Fence Instructions
STEP TWO
Secure the rail to the posts with 3/4” screws on both sides of the
rail as illustrated.
3
x
x
STEP THREE
5
Install fence into Ground
1
2
4
3
Block of Wood
Baskenridge Vinyl Fence Instructions
1
Move the fence to its final location and identify the location
of posts.
Loosen the top 8” to 10” of the ground using a claw hammer
and screw driver (or something equivalent) as illustrated.
Add water to loosen soil.
Use a block of wood to the protect the top of the posts and
gently hammer each post into the ground equally.
2
3
4
x
x
x
x
6Baskenridge Vinyl Fence Instructions
1
If your ground is too hard, or you have more than three or four
panels to install, please consider:
Purchase a 1 3/4” diameter auger bit (commonly used for
planting tulips) as illustrated ($15-$20 on Amazon.com)
Drill a hole in the ground at the desired location only about
8” to 10” deep.
Fill the holes with water as illustrated.
Push fence posts into the holes as illustrated.
2
3
4
1
STEP THREE
OPTIONS IN HARD GROUND
3
2
4
Top Rail
Bottom
Rail
Top Rail
Bottom
Rail
STEP THREE
5
Install fence into Ground - Continued
Level the assembled unit and backfill and compact dirt around
the base of each post to strengthen the unit.
7
Baskenridge Vinyl Fence Instructions
5
Level
STEP FOUR
1
2
Fasten Joiner Clips
Fasten joiner clips by screwing into place on the top of the top
rail and top of the bottom rail as illustrated.
Use the 1” self-tapping screws.
Fasten the opposite end of the joiner clip as illustrated.
8
6935 Reames Rd. Ste. K. Charlotte, NC 28216
Toll Free Phone: 1 877 234 6196 Fax: 704 631 4685
www.zippity-outdoor.com
STEP FIVE
1
Post Caps Installation
Finish the assembly by pushing the post caps down over the
top of posts as illustrated. The post caps will lock into place.
7
OPTIONAL
Angled Installation
The fence panels can also be installed on an angle as shown.
90° Application
45° Application
Altri manuali per Baskenridge
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Zippity Recinzioni e cancelli
Zippity
Zippity ZP19055 Manuale utente
Zippity
Zippity Highland Manuale utente
Zippity
Zippity ZP19002 Manuale utente
Zippity
Zippity ZP19022 Manuale utente
Zippity
Zippity Huntersville ZP19036 Manuale utente
Zippity
Zippity Urban Escape Vinyl Fence Manuale utente
Zippity
Zippity ROGER RABBIT VINYL GARDEN FENCE KIT 3 PACK Manuale utente
Zippity
Zippity Baskenridge Vinyl Gate Kit w/ Fence Wings Manuale utente
Zippity
Zippity ZP19072 Manuale utente
Zippity
Zippity Highland Manuale utente
Zippity
Zippity KESWICK ZP19060 Manuale utente
Zippity
Zippity Manchester ZP19018 Manuale utente
Zippity
Zippity BURBANK Manuale utente
Zippity
Zippity ZP19019 Manuale utente
Zippity
Zippity ZP19062 Manuale utente
Zippity
Zippity ZP19056 Manuale utente
Zippity
Zippity ALL AMERICAN Manuale utente
Zippity
Zippity MANCHESTER VINYL PICKET FENCE KIT Guida rapida
Zippity
Zippity Newport Vinyl Picket Gate Manuale utente
Zippity
Zippity LIBERTY LATTICE ZP19053 Manuale utente
