ZipRip UC5E Manuale utente
Priport Controller
UC5E
Service Manual
(Revision 1-3)
2UC5e SM (Rev1-3) May 2001
Table of Contents
SAFETY INFORMATION .....................................................................3
GENERAL REMARKS .........................................................................4
1. OVERALL INFORMATION.............................................................5
1.1 HOST SYSTEMS ........................................................................................ 5
1.2 BASIC SPECIFICATION ............................................................................. 5
1.3 FONT INFORMATION .................................................................................. 5
1.4 VIDEO INTERFACE KITS ........................................................................... 6
2. BASIC FUNCTION .........................................................................7
2.1 BASIC CONFIGURATION ........................................................................... 7
2.2 SPECIFICATIONS AND CONFIGURATIONS OF I/O PORTS ....................... 8
3. VIDEO I/F INSTALLATION PROCEDURES ..................................9
3.1 VIDEO I/F KIT TYPE 10 PARTS LIST ........................................................ 10
3.2 INSTALLATION PROCEDURES FOR INTERFACE KITS .......................... 10
4. OPERATION VERIFICATION...................................................... 10
4.1 TOOLS ...................................................................................................... 10
4.2 TESTS ...................................................................................................... 10
5. TROUBLES OOTING ................................................................ 12
5.1 BASIC STEPS FOR TROUBLESHOOTING .............................................. 12
5.2 TROUBLESHOOTING FLOW .................................................................... 14
5.3 PRIPORT/UC5E FAILURE IDENTIFICATION............................................. 15
5.4 SUBASSEMBLY TROUBLESHOOTING ................................................... 16
5.5 MEMORY TROUBLESHOOTING .............................................................. 17
5.6 LED STATUS LIGHT SEQUENCE AND CONDITIONS.............................. 17
5.7 DIAGNOSTIC TEST PAGE CONTENTS ................................................... 19
5.8 CHECKING PRINTER DRIVER OPERATION ............................................ 20
5.9 COLLECTING INFORMATION FOR A PROBLEM REPORT ..................... 21
6. DISASSEMBLY / ASSEMBLY .................................................... 22
6.1 REQUIRED TOOLS AND PRECAUTIONS ................................................ 22
6.2 ZIPRIP FOR MODEL C237 ....................................................................... 23
6.3 ZIPRIP FOR MODEL C235........................................................................ 29
6.4 UPGRADING UC5E FIRMWARE .............................................................. 34
6.5 MEMORY REPLACEMENT ...................................................................... 35
7. PARTS LIST ................................................................................ 36
7.1 UC5E FOR MODEL C235 (DIAGRAM) ..................................................... 36
7.2 UC5E FOR MODEL C237 (DIAGRAM) ..................................................... 37
PARTS LIST C235 AND C237 .................................................................. 38
7.3 PC CONTROLLER I/F KIT TYPE 10 .......................................................... 39
3
UC5e SM (Rev1-3) May 2001
IMPORTANT SAFETY NOTICES
PREVENTION OF P YSICAL INJURY
1. Before disassembling or assembling parts of the printer and peripherals, make sure
that the power cord is unplugged.
2. The wall outlet should be near the UC5E and easily accessible.
3. If any adjustment or operation check has to be made with exterior covers off or open
while the main switch is turned on, keep hands away from electrified or mechanically
driven components.
OBSERVANCE OF ELECTRICAL SAFETY STANDARDS
The UC5E must be installed and maintained by a customer service representative who has
completed the training course on those models.
SAFETY AND ECOLOGICAL NOTES FOR DISPOSAL
Dispose of replaced parts in accordance with local regulations.
Safety Information
This equipment must be connected to SELV circuits of other equipment complying with the
requirements of SELV circuits as defined in the standards EN60950,IEC950 and
CSAC22.2 N0. 950, UL 1950.
Renseignements de sécurité
IL est absolunent nécessaire d’ interconnecter cet équipment dux circuits SELV de tout
équipment qui se conforme dux besoirs des circuits SELV comme précisés dux standards
EN60950, IEC950 et CSAC22.2 NO. 950, UL 1950
Diese Ausrüstung muß zur SELV Schaltungen von anderen Ausrüstungen, die mit den
Forderungen von SELV Schaltungen die in den Standards EN60950, IEC950 und
CSAC22.2 N0 950, UL1950 definiert werden, nach kommen.
Sicherheit-Auskünfte
4UC5e SM (Rev1-3) May 2001
General Remarks
The following table shows the conversion of the model names for each manufacturer:
Model Code Company Model Name
C237 Ricoh JP1210/1230/1250
Gestetner 5308/5308L/5308B
RexRotary 1225/1225L/1225B
Nashuatec CP308/CP308L/CP308B
Sa in 3150eDNP
Standard SD330
C235 Ricoh JP8000
Gestetner 5490
RexRotary 1395
Nashuatec CP490
Sa in 3450DNP
Standard SD630
5
UC5e SM (Rev1-3) May 2001
1. OVERALL INFORMATION
1.1 HOST SYSTEMS
UC5E is an embedded GDI raster image processor for PRIPORTs. The following are the
target computer hosts for this UC5E.
Target Host Computer Systems
• IBM PC/AT compatible PC with Windows 3.11 for workgroups, ME, 2000, 95 with
Internet Explorer 4.01 SP1, Windows 98, or Windows NT4.0 with SP3 operating
systems.
There are no minimum system hardware requirements, other than those imposed by the
operating systems.
1.2 BASIC SPECIFICATION
Contents Description
Configuration Internal embedded controller
Priport Models C235 and C237
I/O Interfaces Host:
• Parallel I/F
( ECP/EPP Bi directional)
Video:
RSVI Interface
Fonts True Type
Image Resolution 300 dpi, 600 dpi
RAM Standard:16MB, (72 pin 60ns EDO
SIMM, non parity, at 5 volts with 2K
maximum refresh rate)
Paper Size A3, A4, B4, B5, A5,
Custom size (Operating System
Depending), US Letter, US Legal,
US Tabloid
Table 1.2. Basic UC5E Specifications.
1.3 FONTS
All fonts reside with in the host computer. Systems fonts are all True Type Fonts.
6UC5e SM (Rev1-3) May 2001
1.4 VIDEO INTERFACE KITS
Description Contents
PC Controller I/F Kit Type 10 For the connection to Model C235
and Model C237
Table 1.4. Interface Kits for use with the UC5E.
7
UC5e SM (Rev1-3) May 2001
2. BASIC FUNCTION
2.1 BASIC CONFIGURATION
2.1.1. MAIN BOARD SPECIFICATIONS
Main Printed Circuit Board specifications are listed in the table below.
Description UC5E Controller
CPU A.D.S.P. CHIP
RAM 16MB (SIMM)
Flash ROM 1Mb Programable Eprom
Table 2.1. Main Boar Specifications.
2.1.2. MAIN BOARD LAYOUT
Figure 2.1.2. Main Boar Layout
1Mb Eprom
16Mb SIMM RAM
LED & Button pins Ribbon cable sockets
Power cable socket
ADSP chip
8UC5e SM (Rev1-3) May 2001
2.2 SPECIFICATIONS AND CONFIGURATIONS OF I/O PORT
The ZipRip UC5E Controller supports connection to a computer for printing
from the following port: • Parallel Port (IEEE 128 , ECP/EPP Bi directional)
2.2.1 PARALLEL MINI CENTRONICS INPUT PORT
2.2.1.1 DESCRIPTION
The high performance parallel input/output port on the UC5E utilizes the IEEE 1284 –
1994 design, for high speed communication between the computer and UC5E. Be sure to
use a cable conforming to this design standard to realize the full data speed benefit from
this interface.
2.2.1.2 IEEE 1284 PARALLEL PORT CHARACTERISTICS
Maximum data speed: 2 MBytes/sec.
Maximum cable length: 1 metre (3.5 feet).
Chassis connector type: IEEE 1284 Type B (Centronics).
Design standard: IEEE 1284 – 1994 .
To use this interface at the highest data rate, the parallel port (e.g., LPT1:) on the user’s
computer must be configured as an ECP or ECP/EPP (not EPP) Printer Port.
2.2.1.3 IEEE 1284 PARALLEL PORT PIN OUT
IEEE 1284 Type B Centronics
<= in => out DB25pin Cent Signal Name of Bit Reg Function Notes
=> 1 1 -Strobe C0- Set Low pulse >0.5 us to
send
=> 2 2 Data 0 D0 Set to least significant data
=> 3 3 Data 1 D1
=> Data 2 D2
=> 5 5 Data 3 D3
=> 6 6 Data D
=> 7 7 Data 5 D5
=> 8 8 Data 6 D6
=> 9 9 Data 7 D7 Set to most significant data
<= 10 10 -Ack S6+ IRQ Low Pulse ~ 5 uS, after
accept
<= 11 11 +Busy S7- High for Busy/Offline/Error
<= 12 12 +PaperEnd S5+ High for out of paper
<= 13 13 +SelectIn S + High for printer selected
=> 1 1 -AutoFd C1- Set Low to autofeed one line
<= 15 32 -Error S3+ Low for Error/Offline/
PaperEnd
=> 16 31 -Init C2+ Set Low pulse > 50uS to init
=> 17 36 -Select C3- Set Low to select printer
== 18-25 19-30 Ground
33,17, Ground
16 Ground
9
UC5e SM (Rev1-3) May 2001
3. VI EO I/F INSTALLATION PROCE URES
3.1 VIDEO I/F KIT TYPE-10 PARTS LIST
No. Description Qty.
32 Interface Board 1
33 Relay Harness 1
3 Stepped Screw – M2.6 2
35 Tapping Screw – M3 x 6 2
Table 3.2.1. Vi eo I/F kit Type-10.
3.2 INSTALLATION PROCEDURES FOR INTERFACE KITS
NOTE: 1) The UC5E Controller is designed for the Model C237 and Model C235
range of Digital Duplicators.
2) Numbers in parentheses ( ) in the installation procedures correspond to
the part numbers in Tables 3.1.
3.2.1 MODEL C237
1. Turn off the main switch and unplug the power cord.
2. Remove the upper rear cover.
3. Remove the MPU cover.
4. Connect CN102 of the printed circuit board (32) to CN110 of the MPU board and
secure it using two screws (35).
5. Connect the harness (33) to CN101 of the printed circuit Board, and
secure it to the connector bracket using two stepped screws (34).
6. Remove the communications port cover plate (blinding cover) from the upper rear
cover.
7. Reinstall the MPU cover.
8. Reinstall the upper rear cover.
NOTE: The On line key on the operation panel is enabled automatically when the
UC5E and interface kit are installed.
10 UC5e SM (Rev1-3) May 2001
4. OPERATION VERIFICATION
Operation verification of the UC5E consists of using the UC5E with a computer and a
PRIPORT to verify that all I/O ports function properly.
4.1 TOOLS
The following items are needed to perform an operational verification of the UC5E.
1) A Priport
2) A UC5E and all items parts
3) A PC running any of the specified operating systems listed in 1.1. of this manual.
4.2 TESTS
Verification of correct operation of all ports and status lights verifies that the UC5E is
operating normally. Refer to Activity Indicator in the Installation manual.
4.2.1PRELIMINARY VERIFICATION OF PRIPORT AND VIDEO INTERFACE
OPERATION
1) Verify that the following parts are properly connected:
a) I/F Board to the Priport Main Board (IPU Board), Model C237 only
b) Shielded Cable to the I/F Board, Model C237 only
c) All other parts of the I/F Kit. Model C237 only
2) Turn the Priport on and, while it is offline (i.e., Online OFF is selected), verify
that,
a) It can produce a good master from a scanned original, and
b) It can print from the master made of the scanned original.
3) Enable the “Online Mode” while the Priport is in the SP MODE, and verify
that the
a) The Online LED illuminates when the Online Key is pressed, and
b) No error is displayed on LCD of Priport. If so, recover from the error.
4.2.2PROCEDURE TO VERIFY UC5E POWER ON SEQUENCE AND PRIPORT
INTERFACE
1) This verification can only be done once installation is complete.
2) Put the Priport ONLINE.
3) Wait while the UC5E conducts its turn on self diagnostic test (takes about
6 seconds.)
4) Check the UC5E LED status lights:
a) The right red light stays on when the power on switch is processed.
Altri manuali per UC5E
2
Indice
