ZKTeco DL30DB Manuale utente

Installation Guide

Version: 1.0

Date: July,2017

DL30DB Digital Lock with Voice Guide Feature

Before Installation

Diagram

1

A

B

C

C

D

F

EG

H

I

J

K

L

MN

56mm 6 4mm

25mm 35mm

20mm 30mm

Mounting Hardware Package Mounting Hardware Package

for door thickness of 30-38mm for door thickness of 39-46mm

A

H

E

L

M

J

H

E

L

M

J

G

FK

Packing List

D

CI

2

B

N

Door Preparation

Note: The standard lock includes 2 mounting hardware packages only, which are used for the door

thickness of 30-38mm and 39-46mm separately.

Note: Please refer to the above picture to adjust the direction of strike plate F and latch D.

1. Check the door thickness and prepare the corresponding mounting

hardware package.

2. Check door opening direction.

30~38 56 20 10 25

39~46 64 30 10 35

47~54 72 35 10 40

55~60 80 45 10 50

H Spindle Length

(mm)

J Screw Length

(mm)

M Screw Length

(mm)

L Screw Length

(mm)

Door Thickness

(mm)

3

Left inward Right inward

Left outward Right outward

F

FF

F

D

DD

D

4

3. Change latch (D) direction.

Fix the latch trim panel by using screws.

Remove screws from the latch trim panel with a

screwdriver and rotate the latch bolt at 180°.

Hexagon Screw

N

A

How To Use Mechanical Key And Change Handle Direction?

Remarks

1. New lock is configured to grant any password or card access.

2. The lock is equipped with mechanical keys for manual unlocking. Remove mechanical keys from the

package and keep them in a safe place.

3. To power up the lock, four alkaline AA batteries (not included) are required. Non-alkaline and

rechargeable batteries are NOT recommended.

4. The operation of lock setting has a stand-by time limit of 10 seconds; if there is no any activity, the lock

will shut off after 10 seconds.

5

Note 1: Align the template along the vertical center

line of the latch(D) at the desired handle height,

and tape it to the door.

Note 2: Mark the holes first, and then start drilling.

1. Drill holes on the door. 2. Install the latch (D).

E

E

D

center line of the

handle

desired handle

height

Installation

6

62mm

3. Install outdoor unit (B) with gasket (C) and spindle(H) on the door.

7

Correct Position: T he small triangle

must be vertically upward.

Incorrect position

H

B

C

4. Install mounting plate (I) with gasket (C) on the door.

J

5. Install indoor unit (K).

M

Note : Push cable into the hole first.

L

B

C

I

I

C

J

8

M

L

K

6. Insert batteries.

EG

F

7. Mark and drill holes for the strike.

8. Test the lock by rotating the back handle and using the mechanical

key (A).

Note : When the door is l ocked and the clutch is idle, the front handle

can be turned, but the door will remain locked.

9

[43/8"]

24 mm

[15/16"]

111 mm

22 mm

[55/64"]

29 mm

[19/64"]

3mm

[1/8"]

[43/8"]

72 mm

Indice

Altri manuali ZKTeco Serratura

Manuali Serratura popolari di altre marche

Magic

Magic 105 Manuale utente

Gantner

Gantner GAT NET.Lock 7020 System Guida rapida

Wittkopp

Wittkopp Insys 7202 Manuale utente

Dorma

Dorma Studio Classic Manuale utente

Securam

Securam ECSL-601 Manuale utente

Sudhaus

Sudhaus 3003 Manuale utente

Safety 1st

Safety 1st 48517 Manuale utente

Pado

Pado FDS-10 Manuale utente

Esco

Esco systeQ Series Manuale utente

COMPX

COMPX National D8951 Manuale utente

secureo

secureo Key Box Manuale utente

Stock Loks

Stock Loks C8713 Manuale utente

COMPX

COMPX 1T-058 Manuale del proprietario

Auslock

Auslock T11 Manuale utente

ELCOM

ELCOM 7205 Manuale utente

Stealth SAFES

Stealth SAFES ShadowVault Manuale utente

Knox

Knox KeySecure 5 Manuale utente

Kwikset

Kwikset 48334/01 Manuale utente