Zomoss DZS02 Manuale utente
ZOMOSS DZS02 Installation Guide
Detect door orientation
(Step 8-9)
Install the physical lock
(Step 1-7)
Change the default master code
(See Quick Set Up)
Customize setting
(See Quick Set Up)
Installation Overview
1
2
3
4
Read this manual carefully before installing and operating!
Important tips to ensure a successful installation:
* Always reset the lock after installation.
* Change the default master code before programming.
* Do not load batteries until lock is completely installed.
Latch
Battery Cover Interior Assembly
Screws
Latch & Strike
Screws
Mounting Plate
Screws
Strike Exterior Assembly Mounting Plate Interior Assembly
Reset Tool
A
F G x 2 H x 4 I x 2 K x 1
J x 1
B C D E
TOOL REQUIRED:
STEP
Installation
Contents
Prepare the door and check dimensions
USE OF A POWERED
SCREWDRIVER IS
NOT RECOMMENDED
A
H
H
C
Micro USB
Power Port
B
D
E
G
I
J
F
1
backset
60 or 70 mm
2-3/8" or 2-3/4"
t
35 mmto 50 mm
1-3/8" o 2"
54 mm
2-1/8"
1"
25 mm
Hold the latch in front of the door
hole, with the latch face flush
against the door edge.
Is the slotted hole centered in the door hole?
Slotted hole is
NOT centered.
Slotted hole is centered.
Rotate and pull the latch
as shown to extend latch.
NO
YES
.Noadjustment is required
Proceedto next step.
2Determine backset and adjust the latch
Do not overtighten screws.
Actual Size
Chiseled
Install the latch
3
STEP
1
1
φ2-3/4"
(70mm)
2
2
4
STEP Install strike and test alignment
IMPORTANT: Make sure hole in
door frame is drilled a minimum
of 1" (25 mm) deep.
1. With the door closed, use
a flat-head screwdriver to
test if deadbolt works
smoothly.
2. Check alignment between
the latch and the strike,
making sure when the
deadbolt is extended, it is
going into the bolt hole and
not hitting the deadbolt
strike or door frame.
H
B
A5Install exterior assembly
STEP
IMPORTANT: Keep metal tailpiece horizontal.
1. Before installation, make sure the latch
is fully retracted (in the unlocked position) .
2. Route the cable below the latch.
unlocked
IMPORTANT: Do not load batteries until lock is completely
installed.
6
STEP
Secure the mounting plate with the screws I.
Do not overtighten screws.
Press the battery cover and pull the
cover up.
Remove battery cover
B
5
STEP
Install interior
assembly
A7
STEP
B7
STEP
Insert the cable connector to
the socket. Push the connector
in firmly until it is completely
seated.
Rotate the thumbturn and
keep it in a vertical position.
Make sure the latch is still
fully retracted (unlocked).
Vertical
unlocked
C
7
STEP
IMPORTANT: Test the thumbturn
for smooth rotation.
If thumbturn doesn’t rotate:
(a) Repeat step 7B, making sure the
thumbturn is vertical with bolt retracted;
(b) Rotate it with much more strength.
Attach Interior assembly to Mounting
Plate and tighten 3 screws.
Actual Size
Press the Reset button first
and keep holding it while
you place the 4th battery
Do not release
the reset button
keep holding the reset button,
until the latch bolt extends.
Door handing
STEP
8A
STEP
8B
reset
bu on
While the door is OPENED and UNLOCKED
(latch retracted), load 3 AA batteries into
the battery compartment.
IMPORTANT: Always run this step after installation.
The motor will not operate before completing the step.
IMPORTANT: If the latch doesn’t extend within 10 seconds, repeat
step 7B and 8A, making sure the thumbturn is always vertical and
latch is always retracted.
unlocked
Ver cal
It’s a factory reset to detect left-hand or
right-hand door orientation.
NOTE:
For best results, use new, non-rechargeable
Alkaline batteries only. Do not mix old and
new batteries.
Test the lock
STEP
9
Unlock
Hit any button to activate keypad
Lock
Press and hold any button for 2 seconds.
Enter default master code 12345678
Hit once
Test with the door open to avoid an accidental lockout.
How to Use
C.
LOCK & UNLOCK from inside
Rotate dial knob to locked and unlocked position
B. LOCK the door from outside
Auto Lock Mode
The bolt will automatically extend
in 30 seconds after unlocking.
You need to enable this feature by
programming.
Press any button on keypad
for 2 seconds
Manual Mode
A. UNLOCK the door from outside
Touch and hold the
sensor with your finger.
Hit any button to activate keypad
hit once
enter master code or user code
d. Contain existing code sequence is an existing code
c. Repeat number sequence
b. Backward number sequence
a. Forward number sequence 123456789
12345
6789
222222222
9467
If
Then
and
94 2467
15 9467
B.
Code is 4-10 digits.
Both master code and user code do not support the following sequence.
Code Format
A.
The default master code is 12345678. This code must be changed
prior to programming the lock.
The Master Code is used for programming and for feature setting.
It will also unlock the lock.
Master Code
Each lock only has one Master Code.
Programming Basic
READ this before proceeding to programming.
C. Micro USB Power Port
There’s a Micro USB charging port under the exterior keypad.
When locked out, or keypad no response, or dead batteries, use a Micro
USB cable to connect a portable phone charger/power bank, it can supply
power for keypad or reboot keypad.
D. Low Battery Indicator
If you see 10 red flashes after pressing any key or lock and unlock the door,
that's an indication that the batteries need to be replaced soon. Please
replace with 4 new AA alkaline batteries and do not mix old and new batteries.
All settings are retained in the memory when the batteries are removed
and replaced.
F. Wrong Entry Limit
After 10 unsuccessful attempts at entering an unauthorized PIN code
or fingerprint, the unit will shut down for 3 minutes.
715 59472 48176
password
Random digits
E. Unlock with Fake code
User can prevent pin code exposure from strangers by entering random
digits before or after pin code.
C.Delete User Code
Master Code Unwanted User Code
You can register 20 fingerprints by this step.
Add User Fingerprint
4
Master Code Scan Fingerprint 5 Times
D
.
B.
You can create 20 sets user codes by this step.
Add User Code
Enter the New User Code Again
Master Code New User Code
Enter New Master Code Again
Current Master Code
Quick Set Up
IMPORTANT: Hit next key within 10 seconds during programming,
otherwise green light goes off then you have to start over.
A. Change Master Code
The default Master Code is 12345678. It is required that you change it
to a code of your own before programming.
New Master Code
Indice
Altri manuali Zomoss Serratura della porta
