Zte MF920 Manuale utente

4G/Wi-Fi hotspot “Beeline”

Internet at home and outdoor

Appearance and review of 4G/Wi-Fi hotspot

controls

Appearance

1. Micro U B connector for connection to computer or charger.

2. LED indicators.

3. Power button. Hold button to turn on/off the device.

4. WP button (Wi-Fi protected setup) and on/off Wi-Fi. Hold button for 5 seconds to activate

WP . hort press to turn on/off Wi-Fi function.

5. U IM card slot.Reset button to reset factory defaults.

LED indicators status description

Indicat

or Name tatus Description

Battery

Blinking red Critical battery level. Please, connect

charger.

olid red Low battery.

Blinking

green Charging battery.

olid green Middle battery level or battery is fully

charged.

Off

Device is turned off, in stand by mode

and not charging, or battery is

removed.

Network signal

olid red Error. No network or U IM card not

inserted.

olid green Registered in 2G/3G network.

Blinking gree

Registered in 2G/3G network and

connected to Internet. Data transfer is

active.

olid blue Registered in 4G network.

Blinking blue

Registered in 4G network and

connected to Internet. Data transfer is

active.

olid blue Unread M .

Blinking blue New M and shines for 10 seconds,

or Full M .

Off No unread M and no new M , or in

power saving mode.

Wi-Fi network olid blue Wi-Fi active.

Blinking blue WP active.

How to use device

To install the router, follow step-by-step instruction to make sure that you have done all correctly.

Getting started

tep 1. Installation of U IM card

1. Remove flip on side of the device.

2. Insert U IM card into the router in right direction. Make sure that U IM card is tightly inserted.

Attention: Correct work of router and software is guaranteed only with "Beeline" U IM.

3. To reset MF 920 to factory defaults press button as per picture below.

Note: You can write or remember network ID and password of Wi-Fi network. It will be need it if you

plan to connect to router via Wi-Fi.

tep 2. Power on

Hold power button on body of device and do not release, before LED indicators will be turned on.

tep3. Connection router with other devices

Connection via U B cable

Connect U B cable to router, then connect U B jack to any free U B port of PC.

Connection via Wi-Fi

1. Make sure that your router is turned on.

2. tart searching wireless networks on device, which you want connect to router.

Note: you must set automatically obtain IP address in device settings, which you are going to connect

with router.

3. In wireless networks list choose needed network name ( ID).Router have following name

format: Beeline_XXXX, where XXXX –number, which is unique for each router. Also you can find name

of network under back cover of your router in the top.

4. Password input will be required. You can find password under back cover of your router after

network name ( ID).

5. After successful connection with router you can open your WEB browser and enter to address

bar: http://m.home or http://192.168.8.1 to access to WEB UI of your router.

tep 4. Installing the application

If you connect your device with router via U B, installation of the "4G/Wi-Fi hotspot “Beeline”" application

starts automatically after a time. Wait installation program starts and follow its prompts. During installation

do not disconnect the router from PC.

PC’s with Microsoft® Windows® O

Installation of the 4G/Wi-Fi hotspot "Beeline" application starts automatically after a time. Wait installation

program starts and follow its prompts. During installation do not disconnect the router from PC. If automatic

installation fails to start, install it manually:

1. Open Computer. To make it, double click the icon Computer on the desktop. If there is no

icon Computer on the desktop, press simultaneously Windows key and E key on your keyboard

and select Beeline disc in the opened window.

2. In the Computer window open Beeline disc. On some PC due to security settings no disk

name can be seen. If no Beeline disk is found in Computer, open newly appeared external disk (e.g.

CD ROM (E:)).

3. In the appeared window find AutoRun.exe and run it.

4. Then follow the installation program prompts and do not disconnect the ruter from PC.

PC’s with Apple Mac O X

1. Open the disk Beeline, which appears on the desktop.

2. If there is no any Beeline disk on the desktop, then press keyboard keys simultaneously

and on the left side of the opened Devices window select Beeline disk.

3. In the opened window look for 4G-Wi-Fi router "Beeline" installation file and execute it.

4G/Wi-Fi hotspot “Beeline”

Internet at home and outdoor

Appearance and review of 4G/Wi-Fi hotspot

controls

Appearance

1. Micro U B connector for connection to computer or charger.

2. LED indicators.

3. Power button. Hold button to turn on/off the device.

4. WP button (Wi-Fi protected setup) and on/off Wi-Fi. Hold button for 5 seconds to activate

WP . hort press to turn on/off Wi-Fi function.

5. U IM card slot.Reset button to reset factory defaults.

LED indicators status description

Indicat

or Name tatus Description

Battery

Blinking red Critical battery level. Please, connect

charger.

olid red Low battery.

Blinking

green Charging battery.

olid green Middle battery level or battery is fully

charged.

Off

Device is turned off, in stand by mode

and not charging, or battery is

removed.

Network signal

olid red Error. No network or U IM card not

inserted.

olid green Registered in 2G/3G network.

Blinking gree

Registered in 2G/3G network and

connected to Internet. Data transfer is

active.

olid blue Registered in 4G network.

Blinking blue

Registered in 4G network and

connected to Internet. Data transfer is

active.

M olid blue Unread M .

Blinking blue New M and shines for 10 seconds,

or Full M .

Off No unread M and no new M , or in

power saving mode.

Wi-Fi network olid blue Wi-Fi active.

Blinking blue WP active.

How to use device

To install the router, follow step-by-step instruction to make sure that you have done all correctly.

Getting started

tep 1. Installation of U IM card

1. Remove flip on side of the device.

2. Insert U IM card into the router in right direction. Make sure that U IM card is tightly inserted.

Attention: Correct work of router and software is guaranteed only with "Beeline" U IM.

3. To reset MF 920 to factory defaults press button as per picture below.

Note: You can write or remember network ID and password of Wi-Fi network. It will be need it if you

plan to connect to router via Wi-Fi.

tep 2. Power on

Hold power button on body of device and do not release, before LED indicators will be turned on.

tep3. Connection router with other devices

Connection via U B cable

Connect U B cable to router, then connect U B jack to any free U B port of PC.

Connection via Wi-Fi

1. Make sure that your router is turned on.

2. tart searching wireless networks on device, which you want connect to router.

Note: you must set automatically obtain IP address in device settings, which you are going to connect

with router.

3. In wireless networks list choose needed network name ( ID).Router have following name

format: Beeline_XXXX, where XXXX –number, which is unique for each router. Also you can find name

of network under back cover of your router in the top.

4. Password input will be required. You can find password under back cover of your router after

network name ( ID).

5. After successful connection with router you can open your WEB browser and enter to address

bar: http://m.home or http://192.168.8.1 to access to WEB UI of your router.

tep 4. Installing the application

If you connect your device with router via U B, installation of the "4G/Wi-Fi hotspot “Beeline”" application

starts automatically after a time. Wait installation program starts and follow its prompts. During installation

do not disconnect the router from PC.

PC’s with Microsoft® Windows® O

Installation of the 4G/Wi-Fi hotspot "Beeline" application starts automatically after a time. Wait installation

program starts and follow its prompts. During installation do not disconnect the router from PC. If automatic

installation fails to start, install it manually:

1. Open Computer. To make it, double click the icon Computer on the desktop. If there is no

icon Computer on the desktop, press simultaneously Windows key and E key on your keyboard

and select Beeline disc in the opened window.

2. In the Computer window open Beeline disc. On some PC due to security settings no disk

name can be seen. If no Beeline disk is found in Computer, open newly appeared external disk (e.g.

CD ROM (E:)).

3. In the appeared window find AutoRun.exe and run it.

4. Then follow the installation program prompts and do not disconnect the ruter from PC.

PC’s with Apple Mac O X

1. Open the disk Beeline, which appears on the desktop.

2. If there is no any Beeline disk on the desktop, then press keyboard keys simultaneously

and on the left side of the opened Devices window select Beeline disk.

3. In the opened window look for 4G-Wi-Fi router "Beeline" installation file and execute it.

4. After that follow installation program prompts and do not disconnect the router from Mac.

WEB UI for 4G/Wi-Fi hotspot “Beeline”

Open WEB UI for 4G/Wi-Fi hotspot “Beeline”. To do it, find icon on Desktop (for Windows O ) and

double click on it, in Mac O - find icon in Dock station.

Attention: if there is no icon on Desktop by some reasons, you can open WEB UI using your Internet

browser. Input in your browser IP address: 192.168.8.1 or WEB address: http://m.home.

Authorization. To access 4G/Wi-Fi hotspot settings you need to enter a password on the login page.

Default password - admin. Enter your password and click "Login”.

Main page. Contain links to all sections, and also information about current router status, network

information etc. Using main page functions, you can establish Internet connection, check your current

balance and move to any section of WEB UI for 4G/Wi-Fi hotspot “Beeline”.

# Name Description

1tatus bar,

language bar

tatus bar displays current U IM

card status, current network type

and signal strength.

Language bar allows you to quickly

switch WEB UI language.

2 Wi-Fi Info

On click will open Wi-Fi settings

section, which allows you configure

Wi-Fi, check current list of

connected devices via Wi-Fi.

3 Connect tile

Allows you to establish connection

with Internet, also will display

current connections status and data

transfer rate. If connection to

Internet is not established, click on

this tile to establish connection. If

connection already established, on

click this connection will be closed.

4 Messages tile

On click will open Messages section,

for reading, sending and deleting

M . Also tile displays the last

incoming message, on click will

open directly this message text.

5 ettings tile On click will open ettings section

for modify current device settings.

6Personal

account

On click will open the

portalhttp://my.beeline.ru/ ,allows

you to manage services online.

7 Account status

On click will open the

portalhttps://balance.beeline.ru/ ,allow

ing to display the online account

balance.

8Manage

ervices tile

On click will open Manage ervices

section for sending U D

commands, for checking current

balance, phone number etc.

9 Help tile On click will open Help section with

information about device.

10 Check balance

tile

Allows you to check your current

balance.

Internal pages. All internal pages made using one template. Each page contain information and control

elements according with section name.

# Name Descrption

1 ection header

Displays current section

title. On click will open

main menu, which allows

you to move between

main sections of WEB UI.

2 Home button

On click will open main

page of WEB UI from any

section or subsection.

3tatus bar, language

bar

tatus bar displays current

U IM card status, current

network type and signal

strength.

Language bar allows you

to quickly switch WEB UI

language.

4 ection menu tile

Displays current section

menu. Allows you to

switch between

subsections of current

section.

5 ubsection header

Displays current

subsection title. If you see

nearby with subsection

name icon of drop down

menu , on click will

open 3rd level menu of

subsection. Use this menu

to switch between

functions of current

subsection.

6 ubsection content Display current

subsections content.

7 Connection status tile On click allows you to

connect/disconnect your

Indice

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza