ZyXEL Communications Network Device NXC-8160s Manuale utente
ENGLISH
1
Overview
The NXC-8160 is a Power over Ethernet (PoE) WLAN controller that supplies power to the
attached access points (APs) via an Ethernet cable. You can connect up to eight APs to
extend your wireless network. You configure all wireless and wireless security settings on
the NXC-8160. The NXC-8160 provides wireless connectivity to your wired network
through the APs. The APs need no configuration and act as an antenna on the NXC-8160.
This guide shows you how to:
1Make initial hardware connections
2Access the web configurator
3Configure the wireless and wireless security settings
4Deploy the NXC-8160 in your network
ENGLISH
ENGLISH
2
1 Make Initial Hardware Connections
Follow the steps below to connect your NXC-8160 for initial configurations.
1Connect an AP(s) to the WLAN port(s) using the included Ethernet cable. At the time of
writing, you can connect only the NWA-8500 model to the WLAN port.
2Connect your computer to the LAN port using an Ethernet cable.
3Connect the power socket on the rear panel to a power source using the included
power cord.
After you have connected the power and turned on the power source, check the LEDs
(lights) on the front panel. The POWER LED turns on. The LINK/ACT and LINK LEDs turn
on when the corresponding ports are connected properly.
1
2
3
ENGLISH
3
VIf none of the LEDs are on, check your connections, and inspect your
cables for damage. Make sure that you have the power cord connected to
the NXC-8160 and plugged in to an appropriate power source. Make sure
the power source is turned on. If the LEDs are still off, contact your local
vendor.
2 Accessing the Web Configurator
To configure your NXC-8160, you need to access it using the web configurator. Use
Internet Explorer 6.0/Netscape 7.0 or a later version.
1Make sure your computer is in the same subnet as the NXC-8160 and connected to the
LAN port.
"The NXC-8160’s default IP address is 192.168.1.10.
2Open your web browser. Enter https://192.168.1.10 as the address.
3When you see the security screens, click OK or Yes to continue.
ENGLISH
4
4The login screen displays. Enter admin as the user name and default as the password
and click OK.
VIf you cannot access the web configurator, make sure your computer is in
the same subnet as the NXC-8160 and the URL you entered in your web
browser begins with “https”.
You may also need to check your browser’s security settings and make
sure your computer’s Ethernet card is installed and functioning properly
5The initial main screen displays as shown.
3 Configure the Wireless and Wireless Security Settings
The NXC-8160 allows two radios (using separate channels and SSIDs). The two radios
can be in either the same or different IEEE 802.11 mode. You can assign up to 16 SSIDs to
each radio. By default, the wireless security is disabled.
ENGLISH
5
If you want to change the SSID(s), allow either IEEE 802.11a and/or IEEE 802.11b/g
compatible wireless clients to access the network behind the NXC-8160, or enable
wireless security, follow the steps below.
1Click WLAN on the navigation panel
to open the WLAN Configuration
screen.
2Select the radio which you want to
configure.
3Specify the 802.11 mode and
channel number.
4Create and/or assign a SSID to the
radio.
5Click Rename SSIDs to change the
SSID.
• You cannot assign the same SSID to
different radios.
• If there is no SSID assigned to a
radio, the radio will be deactivated.
6Click SSID & Security at the
bottom of the WLAN
Configuration screen or on the
navigation panel.
7Select the SSID for which you
want to configure wireless
security settings.
8Select a security mode and
configure the related fields. The
screen changes according to the
security mode you selected. See
the User’s Guide for more
information on wireless security.
VIf a wireless client cannot access the network or the Internet wirelessly,
make sure both the NXC-8160 and the client have the same wireless
settings (such as SSID, channel and IEEE 802.11 standard) and wireless
security settings.
ENGLISH
6
4 Deploy the NXC-8160 in Your Network
After you finish the SSID and wireless security settings, use this section to configure the
NXC-8160’s IP address and connect it to your network.
The NXC-8160’s default IP address is 192.168.1.10 and the subnet mask is
255.255.255.0. If your network is in another subnet or someone in your network is using
this IP address, you need to set the NXC-8160 to another IP address.
1Click LAN on the navigation panel
of the web configurator.
2Give the NXC-8160 an available
static IP address which is in the
same subnet as your network.
3Enter the gateway’s IP address.
4Click Apply and log out of the
web configurator.
5Disconnect the NXC-8160 from
the computer and connect the NXC-8160 to a modem, router or switch in your network.
"To configure the NXC-8160 again, you need to use the new IP address to
access the web configurator.
Procedure to View a Product’s Certification(s)
1Go to www.zyxel.com.
2Select your product from the drop-down list box on the ZyXEL home
page to go to that product's page.
3Select the certification you wish to view from this page.
DEUTSCH
7
Übersicht
Der NXC-8160 ist ein PoE-WLAN-Controller, der die angeschlossenen Access-Points
(APs) über ein Ethernet-Kabel mit Strom versorgt. Sie können Ihr Drahtlosnetzwerk um bis
zu acht APs erweitern. Alle Einstellungen für die Drahtlosverbindungen und alle
Sicherheitseinstellungen werden auf dem NXC-8160 konfiguriert. Der NXC-8160
ermöglicht über die APs den Zugriff auf das kabelgebundene Netzwerk. Die APs müssen
nicht konfiguriert werden, und sie funktionieren wie Antennen am NXC-8160.
Dieses Benutzerhandbuch enthält die folgenden Kapitel:
1Anschließen der Hardware
2Zugreifen auf den Web-Konfigurator
3Konfigurieren der Drahtloseinstellungen und der Drahtlossicherheitseinstellungen
4Benutzen des NXC-8160 im Netzwerk
DEUTSCH
DEUTSCH
8
1 Anschließen der Hardware
Führen Sie die unten beschriebenen Schritte aus, um den NXC-8160 für die
Erstkonfiguration anzuschließen.
1Schließen Sie einen oder mehrere APs mit dem mitgelieferten Ethernet-Kabel an die
WLAN-Ports an. Zum Zeitpunkt der Druckstellung kann nur das Modell NWA-8500 an
den WLAN-Port angeschlossen werden.
2Schließen Sie Ihren Computer mit einem Ethernet-Kabel an den Anschluss LAN an.
3Verbinden Sie den Netzanschluss an der Rückseite des Geräts mit dem mitgelieferten
Stromkabel an das Stromnetz an.
Schalten Sie das Gerät ein, und prüfen Sie die LED-Anzeigen an der Vorderseite des
Geräts. Die POWER LED leuchtet auf. Die LED-Anzeigen LINK/ACT und LINK beginnen
zu leuchten, wenn die Anschlüsse verbunden sind.
1
2
3
DEUTSCH
9
VWenn keine der LEDs leuchtet, prüfen Sie noch einmal alle
Kabelverbindungen. Stellen Sie sicher, dass das Netzkabel richtig an den
NXC-8160 und an eine Netzsteckdose angeschlossen wurde. Stellen Sie
sicher, dass die Stromquelle eingeschaltet ist und richtig funktioniert. Wenn
die LED-Anzeigen weiterhin nicht leuchten, wenden Sie sich an Ihren
Händler.
2 Zugriff auf den Web-Konfigurator
Um den NXC-8160 zu konfigurieren, müssen Sie zunächst mit dem Web-Konfigrator
darauf zugreifen. Verwenden Sie Internet Explorer 6.0/Netscape 7.0 oder neuere
Versionen davon.
1Stellen Sie sicher, dass sich der Computer im selben Subnetz wie der NXC-8160
befindet und an den LAN-Port angeschlossen ist.
"Die Standard-IP-Adresse des NXC-8160 ist 192.168.1.10.
2Starten Sie Ihren Webbrowser. Geben Sie als Adresse https://192.168.1.10 ein.
3Wenn die Sicherheitsfenster angezeigt werden, klicken Sie auf OK oder Yes (Ja).
Questo manuale è adatto per i seguenti modelli
1
Indice
Lingue:
Altri manuali ZyXEL Communications Controllori
ZyXEL Communications
ZyXEL Communications NXC2500 Manuale utente
ZyXEL Communications
ZyXEL Communications NXC-8160 Manuale di istruzioni
ZyXEL Communications
ZyXEL Communications NXC5500 Manuale utente
ZyXEL Communications
ZyXEL Communications NXC2500 Manuale utente
ZyXEL Communications
ZyXEL Communications NXC-8160 Manuale utente
ZyXEL Communications
ZyXEL Communications NXC2500 Manuale utente
ZyXEL Communications
ZyXEL Communications NXC Series Manuale utente
ZyXEL Communications
ZyXEL Communications NXC-8160 Manuale utente
ZyXEL Communications
ZyXEL Communications NXC5500 Manuale utente
ZyXEL Communications
ZyXEL Communications NXC2500 Manuale utente
