ZyXEL Communications Q1000z Manuale utente

www.zyxel.com

802.11n VDSL2 4 GE Port USB

Router over POTS

Firmware v1.00

Edition 1, 5/2010

Q1000z

DEFAULT LOGIN DETAILS

IP Address: http://192.168.0.1

ZyXEL Communications Corporation

Device Panels

LINE (DSL) POWER

PHONE ETHERNET

LEDs (Lights)

RESET

Introduction

Q1000Z is a VDSL2 router that provides super high-speed Internet

access through a telephone line. It allows you to enjoy high-bandwidth

applications, such as video streaming, on-line gaming and peer-to-peer

(P2P). You can also set up a secure wireless network connection using

the WPS button. Additionally, you can connect your telephone to the

Q1000Z and make/receive PSTN calls.

Before You Begin

Make sure you have the following things before you set up your Q1000Z.

• Internet access - account information provided by your ISP, such as

user name, password, and so on.

• Internet Explorer 6.0, Firefox 3.6, Safari: 4.0.5, Opera: 10.51 or

Chrome 4.1.249.1064 as well as later versions of all these

browsers, with JavaScript enabled.

Hardware Connections

This section shows you how to set up your Q1000Z.

1. LINE: Use a telephone wire to connect this port to the telephone jack

or wall outlet.

2. PHONE: Use another telephone wire to connect this port to your

telephone.

3. ETHERNET: Use an Ethernet cable to connect a computer to this port

for initial configuration and/or Internet access.

4. Use the power adaptor provided with your Q1000Z to connect an

appropriate power source to this socket.

As of writing, the USB port is reserved for future use.

Checking the LEDs (Lights)

Look at the LEDs (lights) on the top panel of the Q1000Z.

• The POWER light blinks during start-up and is green once the

Q1000Z is ready.

• The DSL light is green if a physical DSL connection exists and

blinks when transmitting data.

• The INTERNET light is green when Internet access is available.

• The ETHERNET light turns on if the ETHERNET port is properly

connected. The light blinks when the Q1000Z is sending or

receiving data through the ETHERNET port.

• The WIFI light turns on when the wireless network is enabled.

 If none of the LEDs (lights) are on, check your connections.

Make sure that you have the power adaptor connected to the

Q1000Z and plugged in to an appropriate power source.

Make sure the power source is turned on. Turn the Q1000Z

off, wait for a few seconds and turn it back on. If the LEDs

are still off, contact your local vendor.

As of writing, the USB LED is reserved for future use.

Testing Internet Connection

After you have connected the hardware and turned on the Q1000Z, open

a web browser on your computer and go to any web site (for example,

www.zyxel.com) to test your Internet connection.

If you are prompted for a user name and password, enter the account

information as given by your Internet service provider (ISP).

If the INTERNET light is off but the DSL light is on, go to the Initial

Configuration section to configure your Internet access settings.

Initial Configuration

1. Open your browser and enter http://192.168.0.1 (the Q1000Z's

default IP address) as the address.

2. The main screen displays.

 If the main screen does not display, make sure your

computer is set to get an IP address automatically from a

DHCP server.

Click Quick Setup from the main screen. Follow the instructions in

the screen and enter the Internet access information exactly as given

to you by your ISP and click Apply.

3. If your ISP didn’t provide you a username and password, click the

Advanced IP Configuration button. Configure your Q1000Z for

Internet access according to instructions provided by your ISP. Make

sure you enter the correct information.

When your Internet connection is set up correctly, the DSL and

INTERNET lights should be green.

Set Up a WPS Connection

Press the WPS button on the Q1000Z’s front panel for more than 5

seconds to turn the WPS function on.

Follow these steps to add a WPS-enabled device to the wireless network

using the WPS button.

Wall-mounting

Take the following steps to hang your Q1000Z on a wall.

1. Select a position free of obstructions on a sturdy wall.

2. Drill two holes for the screws, exactly 110 mm apart.

Place the devices you want to connect

near one another.

Press the WPS button on the Q1000Z.

The WPS light blinks.

Press the WPS button on a compatible

device within 2 minutes of pressing the

button on the Q1000Z.

The WPS light on the Q1000Z shines

steadily when connected.

3. Be careful to avoid damaging pipes or cables located inside the wall

when drilling holes for the screws.

4. Do not insert the screws all the way into the wall. Leave a small gap of

about 0.5 cm between the heads of the screws and the wall.

5. Make sure the screws are snugly fastened to the wall. They need to

hold the weight of the Q1000Z with the connection cables.

6. Align the holes on the back of the Q1000Z with the screws on the

wall. Hang the Q1000Z on the screws.

Customer Information Statement

The information informing the user of his and the telephone company's

rights and obligations is outlined on the following pages. This information

will be included in the final version of the manual.

1. This equipment complies with Part 68 of the FCC rules and the

requirements adopted by the ACTA. On bottom of this equipment is

a label that contains, among other information, a product identifier of

QWEST Q1000Z. If requested, this number must be provided to the

telephone company.

2. If this equipment DL causes harm to the telephone network, the

telephone company will notify you in advance that temporary

discontinuance of service may be required. But if advance notice isn’t

practical, the telephone company will notify the customer as soon as

possible. Also you will be advised of your right to file a complaint with

the FCC if you believe it is necessary.

3. The telephone company may make changes in its facilities,

equipment, operations or procedures that could affect the operation

of the equipment. If this happens, the telephone company will provide

advance notice in order for you to make necessary modification to

maintain uninterrupted service.

4. If you experience trouble with this equipment, you disconnect it from

the network until the problem has been corrected or until you are sure

that the equipment is not malfunctioning.

5. Please follow instructions for repairing if any (e.g. battery replacement

section); otherwise do not alternate or repair any parts of device

except specified.

Indice

Altri manuali ZyXEL Communications Router di rete

ZyXEL Communications

ZyXEL Communications VMG8825-T50 Manuale utente

ZyXEL Communications

ZyXEL Communications ES-2024 Series Manuale utente

ZyXEL Communications

ZyXEL Communications PRESTIGE 334 Manuale utente

ZyXEL Communications

ZyXEL Communications Prestige 650H-E Series Manuale utente

ZyXEL Communications

ZyXEL Communications ZyXEL EES-1024AF Manuale utente

ZyXEL Communications

ZyXEL Communications VMG8623-T50B Manuale utente

ZyXEL Communications

ZyXEL Communications P-660RU-T1 v3 Manuale utente

ZyXEL Communications

ZyXEL Communications P-791R V2 Manuale

ZyXEL Communications

ZyXEL Communications P-2812HNUL-F1 Manuale utente

ZyXEL Communications

ZyXEL Communications G-120 Manuale utente

ZyXEL Communications

ZyXEL Communications P-791R V2 Manuale utente

ZyXEL Communications

ZyXEL Communications P-335WT Manuale utente

ZyXEL Communications

ZyXEL Communications Dimension ES-3024 Manuale utente

ZyXEL Communications

ZyXEL Communications P-663H-51 Manuale utente

ZyXEL Communications

ZyXEL Communications P-2812HNU-51c Manuale utente

ZyXEL Communications

ZyXEL Communications Dimension ES-124P Guida di riferimento

ZyXEL Communications

ZyXEL Communications Prestige 650HW Manuale utente

ZyXEL Communications

ZyXEL Communications P-791R V2 - V3.40 Manuale utente

ZyXEL Communications

ZyXEL Communications MS-7206 Manuale utente

ZyXEL Communications

ZyXEL Communications PRESTIGE 335 Manuale utente

ZyXEL Communications

ZyXEL Communications P-861H-G2 Manuale utente

ZyXEL Communications

ZyXEL Communications NBG-420N Manuale utente

ZyXEL Communications

ZyXEL Communications Prestige 971M Manuale utente

ZyXEL Communications

ZyXEL Communications P8701T Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza