3idee De-se2417 Manuale utente

www.3idee.eu

de-se2417 VESA Adapter

Assembly instructions

The VESA adapter is compatible with the following products from Dell (dell.com):

S2216M, S2316H, S2316M, S2317HJ, S2416H, S2717Q, S2817Q, SE2216H,

SE2416H, SE2416HSC, SE2416HX, SE2716H, SE2716H, SE2717HR,

SE2717HX and SE2417HGX.

The VESA adapter allows you to conveniently mount your DELL brand monitor to a

monitor arm with a VESA hole pattern (75 x 75mm). Use the included screws and

nuts.

If you want to mount your VESA adapter directly to the wall, use suitable screws

and dowels (not included).

2

Assembly instructions

Assembly instruction

Step 1

Place your screen in a safe, soft place so that your screen

does not get damaged.

Remove the base of your monitor if it is already attached.

Use a screwdriver and press it into the white dot above the

base.

Figure

Step 2

Slide the VESA adapter into the screen as shown. (Figure 1)

When you hear a "click" sound, the adapter has successfully

snapped into place and is securely connected to the screen.

To check: Pull a little on your adapter to test if it is properly

engaged.

Figure 1

Step 3

Check again if the VESA adapter is firmly connected to the

monitor. (Figure 2)

Figure 2

3Assembly instructions

Step 4

Now hold the VESA adapter on your monitor arm and screw

it tight from behind with the other hand. (Figure 3)

Figure 3

Step 5

When fully assembled, it should now look as shown. (Figure

4)

Figure 4

4

Assembly instructions

Safety instructions

General notes

Make sure that all screws are tight and that the monitor audibly clicks into place during installation (if

available).

The material of the adapter is not heat resistant. Avoid direct heat around the adapter such as PC

exhaust or direct sunlight in summer.

PLA is UV resistant but not suitable for high temperatures.

Avoid jerky movements (pulling, tearing) on the PC monitor. This can affect the performance of the

VESA adapter.

Do not subject the PC monitor to excessive loads such as leaning or pushing. This can impair the

performance of the VESA adapter.

Material Notes

The adapter is made of high-quality polylactide (PLA) plastic. PLA is both a colorfast and UV-resistant

material and has low flammability. Polylactide has a low temperature resistance of approx. 45°C-55°C

and is therefore not suitable for use in the vicinity of direct heat and heat sources.

We wish you a lot of fun with your product.

Your 3idee Team

Responsible for this content:

3idee Technologies S.à r.l

5, ZA Um Lenster Bierg

L-6125 Junglinster

Luxembourg

Powered by TCPDF (www.tcpdf.org)

Indice

Altri manuali 3idee Adattatore

Manuali Adattatore popolari di altre marche

PCB Piezotronics

PCB Piezotronics 090B274 Manuale utente

Auvidea

Auvidea J20 Manuale del prodotto

Gossen MetraWatt

Gossen MetraWatt AT3-III E Manuale utente

Akribis

Akribis ITF-21-BISS-MIT Manuale utente

Tenda

Tenda W54U Manuale utente

ROHO

ROHO AGILITY Manuale utente

PROLiNK

PROLiNK WN2001 Manuale utente

Hawking

Hawking HUF2 Manuale utente

Airlink101

Airlink101 AWLC4030 Manuale utente

NETGEAR

NETGEAR XAV101v1 - Powerline AV Ethernet Adapter Manuale utente

Philips

Philips SWA4554S/10 Manuale utente

JVC

JVC TS-C9D2B Manuale di istruzioni

NETGEAR

NETGEAR A6100 Manuale utente

D-Link

D-Link DWA-121 Manuale utente

Philips

Philips SWA2037 Manuale utente

Basalte

Basalte 0610-20 Manuale utente

Yealink

Yealink EHS40 Manuale utente

Balluff

Balluff BIC 1B0-IT1A7-Q40KFU-SM4A4A Manuale utente